View BT136S-600E_1202596.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

?2002 teccor electronics i http://www.teccor.com thyristor product catalog +1 972-580-7777 thyristor product catalog teccor electronics 1800 hurd drive irving, texas 75038 united states of america phone: +1 972-580-7777 fax: +1 972-550-1309 website: http://www.teccor.com e-mail: power.techsales@teccor.com
http://www.teccor.com ii ?2002 teccor electronics +1 972-580-7777 thyristor product catalog teccor electronics reserves the right to make changes at any time in order to improve designs and to supply the best products p ossible. the information in this catalog has been carefully checked and is believed to be accurate and reliable; however, no liability o f any type shall be incurred by teccor for the use of the circuits or devices described in this publication. furthermore, no license of an y patent rights is implied or given to any purchaser . teccor electronics is the proprietor of the quadrac? trademark. is a registered trademark of underwriters laborato- ries, inc. all other brand names may be trademarks of their respective companies. to conserve space in this catalog, the trademark sign (?) is omitted.
?2002 teccor electronics iii http://www.teccor.com thyristor product catalog +1 972-580-7777 contents product selection guide product descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vi circuit requirement diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vii product packages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - viii description of part numbers- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - x quality and reliability assurance - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - xii standard terms and conditions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - xiv data sheets v-i characteristics of thyristor devices - - - - - - - - - - - - - - - - - - - - - - - - e0-2 electrical parameter terminology - - - - - - - - - - - - - - - - - - - - - - - - - - - - e0-3 electrical specifications sensitive triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e1 triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e2 quadracs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e3 alternistor triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e4 sensitive scrs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e5 scrs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e6 rectifiers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e7 diacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e8 sidac - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e9 mechanical specifications package dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - m1 lead form dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - m2 packing options - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - m3 application notes fundamental characteristics of thyristors - - - - - - - - - - - - - - - - - - - an1001 gating, latching, and holding of scrs and triacs - - - - - - - - - - - - - an1002 phase control using thyristors- - - - - - - - - - - - - - - - - - - - - - - - - - - an1003 mounting and handling of semiconductor devices - - - - - - - - - - - - - an1004 surface mount soldering recommendations - - - - - - - - - - - - - - - - - an1005 testing teccor semiconductor devices using curve tracers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - an1006 thyristors used as ac static switches and relays - - - - - - - - - - - - an1007 explanation of maximum ratings and characteristics for thyristors - an1008 miscellaneous design tips and facts - - - - - - - - - - - - - - - - - - - - - - an1009 thyristors for ignition of fluorescent lamps - - - - - - - - - - - - - - - - - - an1010 appendix cross reference guide - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - a1 part numbers index- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - a27
http://www.teccor.com iv ?2002 teccor electronics +1 972-580-7777 thyristor product catalog
?2002 teccor electronics p - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 product selection guide product descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - p 2 circuit requirement diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - p 3 product packages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - p 4 description of part numbers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - p 6 quality and reliability assurance - - - - - - - - - - - - - - - - - - - - - - - - - p 8 standard terms and conditions - - - - - - - - - - - - - - - - - - - - - - - - - p 10
http://www.teccor.com p - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog(972) 580-7777 product descriptions thyristors a thyristor is any semiconductor switch with a bi-stable action depending on p-n-p-n regenerative feedback. thyristors are nor- mally two- or three-terminal devices for either unidirectional or bi- directional circuit configurations. thyristors can have many forms, but they have certain commonalities. all thyristors are solid state switches that are normally open circuits (very high impedance), capable of withstanding rated blocking/off-state voltage until trig- gered to on state. when triggered to on state, thyristors become a low-impedance current path until principle current either stops or drops below a minimum holding level. after a thyristor is triggered to on-state condition, the trigger current can be removed without turning off the device. thyristors are used to control the flow of electrical currents in applications including: ? home appliances (lighting, heating, temperature control, alarm activation, fan speed) ? electrical tools (for controlled actions such as motor speed, sta- pling event, battery charging) ? outdoor equipment (water sprinklers, gas engine ignition, elec- tronic displays, area lighting, sports equipment, physical fitness) sensitive triacs teccor's sensitive gate triacs are ac bidirectional silicon switches that provide guaranteed gate trigger current levels in quadrants i, ii, iii, and iv. interfacing to microprocessors or other equipment with single polarity gate triggering is made possible with sensitive gate triacs. gate triggering currents of 3 ma, 5 ma, 10 ma, or 20 ma may be specified. sensitive gate triacs are capable of controlling ac load currents from 0.8 a to 8 a rms and can withstand operating voltages from 200 v to 600 v. triacs teccor's triac products are bidirectional ac switches, capable of controlling loads from 0.8 a to 35 a rms with 10 ma, 25 ma, and 50 ma i gt in operating quadrants i, ii and iii. triacs are useful in full-wave ac applications to control ac power either through full-cycle switching or phase control of current to the load element. these triacs are rated to block voltage in the ?off? condition from 200 v minimum with selected products capable of 1000 v operation. typical applications include motor speed con- trols, heater controls, and incandescent light controls. quadrac quadrac devices, originally developed by teccor, are triacs and alternistor triacs with a diac trigger mounted inside the same pack- age. these devices save the user the expense and assembly time of buying a discrete diac and assembling in conjunction with a gated triac. the quadrac is offered in capacities from 4 a to 15 a rms and volt- ages from 200 v ac to 600 v ac. alternistor triacs the teccor alternistor is specifically designed for applications required to switch highly inductive loads. the design of this special chip effectively offers the same performance as two thyristors (scrs) wired inverse parallel (back-to-back). this new chip construction provides the equivalent of two electri- cally-separate scr structures, providing enhanced dv/dt charac- teristics while retaining the advantages of a single-chip device. teccor manufactures 6 a to 40 a alternistors with blocking voltage rating from 200 v to 1000 v. alternistors are offered in to-220, to-218, and to-218x packages with isolated and non-isolated versions. sensitive scrs teccor's sensitive gate scrs are silicon-controlled rectifiers repre- senting the best in design, performance, and packaging techniques for low- and medium-current applications. anode currents of 0.8 a to 10 a rms can be controlled by sensitive gate scrs with gate drive currents ranging from 12 a to 500 a. sensitive gate scrs are ideally suited for interfacing to integrated circuits or in applications where high current load requirements and limited gate drive current capabilities exist. examples include igni- tion circuits, motor controls, and dc latching for alarms in smoke detectors. sensitive gate scrs are available in voltage ratings to 600 v ac. scrs teccor's scr products are half-wave, silicon-controlled rectifiers that represent the state of the art in design and performance. load current capabilities range from 1 a to 70 a rms, and voltages from 200 v to 1000 v may be specified to meet a variety of appli- cation needs. because of its unidirectional switching capability, the scr is used in circuits where high surge currents or latching action is required. it may also be used for half-wave-type circuits where gate-con- trolled rectification action is required. applications include crow- bars in power supplies, camera flash units, smoke alarms, motor controls, battery chargers, and engine ignition. surge current ratings are available from 30 a in the to-92 packag- ing to 950 a in the to-218x package. rectifiers teccor manufactures 15 a to 25 a rms rectifiers with voltages rated from 200 v to 1000 v. due to the electrically isolated to-220 package, these rectifiers may be used in common anode or com- mon cathode circuits using only one part type, thereby simplifying stock requirements. diacs diacs are trigger devices used in phase control circuits to provide gate pulses to a triac or scr. they are voltage-triggered bidirec- tional silicon devices housed in do-35 glass axial lead packages and do-214 surface mount packages. diac voltage selections from 27 v to 45 v provide trigger pulses closely matched in symmetry at the positive and negative break- over points to minimize dc component in the load circuit. some applications include gate triggers for light controls, dimmers, power pulse circuits, voltage references in ac power circuits, and triac triggers in motor speed controls. sidacs sidacs represent a unique set of thyristor qualities. the sidac is a bidirectional voltage triggered switch. some characteristics of this device include a normal 95 v to 330 v switching point, negative resistance range, latching characteristics at turn-on, and a low on- state voltage drop. one-cycle surge current capability up to 20 a makes the sidac an ideal product for dumping charged capacitors through an inductor in order to generate high-voltage pulses. applications include light controls, high-pressure sodium lamp starters, power oscillators, and high-voltage power supplies.
?2002 teccor electronics p - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 circuit requirement diagram bilateral voltage switch rectifier reverse blocking thyristor bidirectional thyristor bilateral voltage trigger sidac * rectifier * diac * gate control diac trigger direct gate current 12-500 a 10-50 ma scr * scr (sensitive) * quadrant operation (see quadrant chart on data sheet) i i i i i i i i i i i i i v gate current 10-100 ma gate current 3-20 ma sensitive triac * triac * options internal external diacs * quadrac * alternistor triac * * for detailed information, see specific data sheet in product catalog.
http://www.teccor.com p - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog(972) 580-7777 product packages * no center lead on to-92 sidacs. package code isolated mounting tab gy s c e l k j p product type current (amps) do-15 do-35 do-214 compak to-92 * to-220 to-218 to-218x to-3 fastpak sensitive triac 0.8 ? ? 1 ? ? 4 ? 6 ? 8 ? triac 0.8 ?? 1 ?? 4 ? 6 ? 8 ? 10 ? 15 ? 25 ? 35 ? quadrac 4 ? 6 ? 8 ? 10 ? 15 ? alternistor 6 ? 8 ? 10 ? 12 ? 16 ? 25 ??? 30 ? 35 40 ?? sensitive scr 0.8 ? ? 1.5 ? 4 6 ? 8 ? 10 ? scr 1 ?? 6 ? 8 ? 10 ? 12 15 ? 16 20 ? 25 ? 35 ?? 40 55 65 ?? 70 rectifier 15 ? 20 ? 25 ? diac ?? sidac ? ? ? *
?2002 teccor electronics p - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 product packages non-isolated mounting tab package code frmwdvn to-202 to-220 to-218 to-218x to-252 d-pak to-251 v-pak to-263 d 2 pak current (amps) product type 0.8 sensitive triac 1 ? ? ? 4 ? ? 6 ? ? 8 0.8 triac 1 ? ?? 4 ?? ? 6 ?? ? 8 ?? ? 10 ? ? 15 ? ? 25 35 4 quadrac 6 8 10 15 ? ??? 6 alternistor ? ??? 8 ? ? 10 ? ? 12 ? ? 16 ? ? 25 30 ? 35 40 ? 0.8 sensitive scr ? 1.5 ? ? ? ? 4 ? ? ? ? 6 ? ? ? ? 8 ? ? ? ? 10 1 scr ? ?? 6 ?? ?? 8 ?? ?? 10 ??? 12 15 ? ? 16 20 ? ? 25 35 ? ? 40 ??? ? 55 65 ? 70 15 rectifier 20 25 diac ? sidac
http://www.teccor.com p - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog(972) 580-7777 description of part numbers sensitive triac quadrac sensitive scr triac and alternistor l 20 04 f5 12 device type l = sensitive triac voltage rating 20 = 200 v 40 = 400 v 60 = 600 v current rating package type blank = compak (surface mount) d = to-252 (surface mount) e = to-92 (isolated) f = to-202 (non-islolated) l = to-220 (isolated) v = to-251 (non-islolated) gate variations 3 = 3 ma (q i, ii, iii, iv) 5 = 5 ma (q i, ii, iii, iv) 6 = 5 ma (q i, ii, iii) 6 = 10 ma (q iv) 8 = 10 ma (q i, ii, iii) 8 = 20 ma (q iv) lead form dimensions to-202 to-220 to-92 x special options v = 4000 v isolation (to-220 package only) x8 = 0.8 a n = 1 a 01 = 1 a 04 = 4 a 06 = 6 a 08 = 8 a q2004 l t 52 device type q = quadrac voltage rating 20 = 200 v 40 = 400 v 60 = 600 v current rating 04 = 4 a 06 = 6 a 08 = 8 a 10 = 10 a 15 = 15 a package type l = to-220 (isolated) gate variation t = internal diac trigger lead form dimensions to-220 x special options v = 4000 v isolation (to-220 package only) h alternistor q 20 04 f3 1 device type q = triac or alternistor voltage rating 20 = 200 v 40 = 400 v 60 = 600 v 80 = 800 v k0 = 1000 v current rating x8 = 0.8 a 01 = 1 a 04 = 4 a 06 = 6 a 08 = 8 a 10 = 10 a 12 = 12 a 15 = 15 a 25 = 25 a 30 = 30 a 35 = 35 a 40 = 40 a gate variation dh3 and vh3 = 10ma (q i, ii, iii) 3 = 10 ma (q i, ii, iii) h3 = 20ma (q i, ii, iii) 4 = 25 ma (q i, ii, iii) h4 = 35 ma (q i, ii, iii) * 5 = 50 ma (q i, ii, iii) h5 = 50 ma (q i, ii, iii) * 6 = 80 ma (q i, ii, iii) * 7 = 100 ma (q i, ii, iii) * lead form dimensions to-202 to-220 to-92 to-218x to-218 x special options v = 4000 v isolation (to-220 package only) package type d = to-252 (surface mount) e = to-92 (isolated) f = to-202 (non-isolated) j = to-218x (isolated) k = to-218 (isolated) l = to-220 (isolated) n = to-263 (surface mount) p = fastpak (isolated) r = to-220 (non-isolated) v = to-251 (non-isolated) w = to-218x (non-isolated) * note: alternistor device; no quadrant iv operation s 20 06 fs2 21 device type s = sensitive scr voltage rating 20 = 200 v 40 = 400 v 60 = 600 v current rating x8 = 0.8 a n = 1 a 06 = 6 a 08 = 8 a 10 = 10 a package type blank = compak (surface mount) d = to-252 (surface mount) f = to-202 (non-islolated) l = to-220 (isolated) v = to-251 (non-islolated) gate variations s1 = 50 a s2 = 200 a s3 = 500 a lead form dimensions to-202 to-220 x special options v = 4000 v isolated (to-220 package only) ec 103 d 1 75 device type tcr = to-92 (isolated) ec = to-92 (isolated) t = to-202 (non-isolated) 2n = jedec (isolated) voltage rating for tcr -4 = 200 v -6 = 400 v -8 = 600 v current rating for tcr 22 = 1.5 a lead form dimensions to-92 to-202 current rating for ec 103 = 0.8 a current rating for t 106 = 4 a (i gt = 200 a) 107 = 4 a (i gt = 500 a) current rating for 2n 5xxx = 0.8 a gate current (for ec series only) none = 200 a 1 = 12 a 2 = 50 a 3 = 500 a voltage rating for ec and t b = 200 v d = 400 v m = 600 v voltage rating for 2n 5064 = 200 v 6565 = 400 v
?2002 teccor electronics p - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 description of part numbers scr rectifier diac sidac s 20 08 f12 device type s = non-sensitive scr voltage rating 20 = 200 v 40 = 400 v 60 = 600 v 80 = 800 v k0 = 1000 v current rating 01 = 1 a 06 = 6 a 08 = 8 a 10 = 10 a 12 = 12 a 15 = 15 a 16 = 16 a 20 = 20 a 25 = 25 a 35 = 35 a 55 = 55 a 65 = 65 a 70 = 70 a package type d = to - 252 (surface mount) e = to - 92 (isolated) f = to-202 (non-isolated) j = to-218x (isolated) k = to-218 (isolated) l = to-220 (isolated) m = to-218 (non-isolated) n = to-263 (surface mount) r = to-220 (non-isolated) v = to - 251 (non-isolated) w = to-218x (non-isolated) lead form dimensions to - 202 to - 220 to - 92 to - 218x to - 218 x special options v = 4000 v isolation (to-220 package only) d 20 15 l55 device type d = rectifier voltage rating 20 = 200 v 40 = 400 v 60 = 600 v 80 = 800 v k0 = 1000 v current rating 15 = 15 a 20 = 20 a 25 = 25 a package type l = to-220 (isolated) lead form dimensions to-220 v special options v = 4000 v isolation ht 32 91 device type ht = diac trigger in do-35 st = diac trigger in do-214 lead form dimensions do-35 voltage rating 32 = 27 v to 37 v 35 = 30 v to 40 v 40 = 35 v to 45 v 32a / 5761 = 28 v to 36 v 32b / 5761a = 30 v to 34 v 34b = 32 v to 36 v 36a / 5762 = 32 v to 40 v 36b = 34 v to 38 v k 105 0 e70 device type k = sidac voltage rating 105 = 95 v to 113 v 110 = 104 v to 118 v 120 = 110 v to 125 v 130 = 120 v to 138 v 140 = 130 v to 146 v 150 = 140 v to 170 v 200 = 190 v to 215 v 220 = 205 v to 230 v 240 = 220 v to 250 v 250 = 240 v to 280 v 300 = 270 v to 330 v current rating 0 = 1 a package type e = to-92 (isolated) f = to-202 (non-islolated) g = do-15x (isolated) s = do-214 (surface mount) lead form dimensions to-202 to-92
http://www.teccor.com p - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog(972) 580-7777 quality and reliability it is teccor?s policy to ship quality products on time. we accom- plish this through total quality management based on the funda- mentals of customer focus, continuous improvement, and people involvement. in support of this commitment, teccor applies the following princi- ples: ? employees shall be respected, involved, informed, and qualified for their job with appropriate education, training, and experience. ? customer expectations shall be met or exceeded by consistently shipping products that meet the agreed specifications, quality levels, quantities, schedules, and test and reliability parameters. ? suppliers shall be selected by considering quality, service, deliv- ery, and cost of ownership. ? design of products and processes will be driven by customer needs, reliability, and manufacturability. it is the responsibility of management to incorporate these principles into policies and systems. it is the responsibility of those in leadership roles to coach their people and to reinforce these principles. it is the responsibility of each individual employee to follow the spirit of this statement to ensure that we meet the primary policy ? to ship quality products on time. quality assurance incoming material quality teccor ?vendor analysis? programs provide stringent require- ments before components are delivered to teccor. in addition, purchased materials are tested rigidly at incoming inspection for specification compliance prior to acceptance for use. process controls from silicon slice input through final testing, we use statistical methods to control all critical processes. process audits and lot inspections are performed routinely at all stages of the manufac- turing cycle. parametric testing all devices are 100% computer tested for specific electrical char- acteristics at critical processing points. final inspection each completed manufacturing lot is sampled and tested for compliance with electrical and mechanical requirements. reliability testing random samples are taken from various product families for ongoing reliability testing. finished goods inspection product assurance inspection is performed immediately prior to shipping. design assurance the design and production of teccor devices is a demanding and challenging task. disciplined skills coupled with advanced com- puter-aided design, production techniques, and test equipment are essential elements in teccor's ability to meet your demands for the very highest levels of quality. all products must first undergo rigid quality design reviews and pass extensive environmental life testing. teccor uses statistical process control (spc) with associated control charts throughout to monitor the manufacturing processes. only those products which pass tests designed to assure tec- cor's high quality and reliability standards, while economically satisfying customer requirements, are approved for shipment. all new products and materials must receive approval of qra prior to being released to production. the combination of reliability testing, process controls, and lot tracking assures the quality and reliability of teccor's devices. since even the best control systems cannot overcome measure- ment limitations, teccor designs and manufactures its own com- puterized test equipment. teccor's reliability engineering group conducts ongoing product reliability testing to further confirm the design and manufacturing parameters.
?2002 teccor electronics p - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 quality and reliability reliability stress tests the following table contains brief descriptions of the reliability tests commonly used in evaluating teccor product reliability on a peri- odic basis. these tests are applied across product lines dependi ng on product availab ility and te st equipment ca pacities. other tests may be performed when appropriate. flammability test for the ul 94v0 flammability test, all expoxies used in teccor encapsulated devices are recognized by underwriters laboratories test type typical conditions test description standards high temperature ac blocking t a = 100 c to 150 c, bias @ 100% rated v drm , t = 24 hrs to 1000 hrs evaluation of the reliability of product under bias conditions and elevated temperature mil-std-750, m-1040 high temperature storage life t a = 150 c, t = 250 to 1000 hrs evaluation of the effects on devices after long periods of storage at high temperature mil-std-750, m-1031 temperature and humidity bias life t a = 85 c to 95 c, rh = 85% to 95% bias @ 80% rated v drm (320 vdc max) t = 168 to 1008 hrs evaluation of the reliability of non- hermetic packaged devices in humid environments eia / jedec, jesd22-a101 temperature cycle [air to air] t a = -65c to 150c, cycles = 10 to 500 evaluation of the device?s ability to withstand the exposure to extreme temperatures and the forces of tce during transitions between temperatures mil-std-750, m-1051, eia / jedec, jesd22-a104 thermal shock [liquid to liquid] t a = 0 c to 100 c, t txfr = 10 s, cycled = 10 to 20 evaluation of the device?s ability to withstand the sudden changes in temperature and exposure to extreme temperatures mil-std-750, m-1056 autoclave t a = 121 c, rh = 100%, p = 15 psig, t = 24 hrs to 168 hrs accelerated environmental test to evaluate the moisture resistance of plastic packages eia / jedec, jesd22-a102 resistance to solder heat t a = 260 c, t = 10 s evaluation of the device?s ability to withstand the temperatures as seen in wave soldering operations mil-std-750, m-2031 solderability steam aging = 1 hr to 8 hrs, t solder = 245 c, flux = r evaluation of the solderability of device terminals after an extended period mil-std-750, m-2026, ansi-j-std-002
http://www.teccor.com p - 10 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog(972) 580-7777 standard terms and conditions supplier shall not be bound by any term proposed by buyer in the absence of written agreement to such term signed by an autho- rized officer of supplier. (1) price: (a) supplier reserves the right to change product prices at any time but, whenever practicable, supplier will give buyer at least thirty (30) days written notice before the effective date of any price change. unless supplier has specifically agreed in writing, signed by an authorized officer of supplier, that a quoted price shall not be sub- ject to change for a certain time, all products shipped on or after the effective date of a price change may be billed at the new price level. (b) whenever supplier agrees to a modification of buyer's order (which modification must be in writing and signed by an authorized officer of supplier), supplier reserves the right to alter its price, whether or not such price was quoted as ?firm.? (c) prices do not include federal, state or local taxes, now or hereafter enacted, applicable to the goods sold. taxes will be added by supplier to the sales prices whenever supplier has legal obligati on to collect them and will be paid by buyer as invoiced unless buyer provides sup- plier with a proper tax exemption certificate. (2) production: supplier may, at its sole discretion and at any time, withdraw any catalog item from further production without notice or liability to buyer. (3) interest: (a) all late payments shall bear interest thirty (30) days after the due date stated on the invoice until paid at the lower of one and one-half percent per month or the maximum rate permitted by law. all interest becoming due shall, if not paid when due, be added to principal and bear inter- est from the due date. at supplier's option, any payment shall be applied first to interest and then to principal. (b) it is the intention of the parties to comply with the laws of the jurisdiction governing any agreement between the parties relating to interest. if any construction of the agreement between the parties indicates a different right given to supplier to demand or receive any sum greater than that permissible by law as interest, such as a mistake in calculation or wording, this paragraph shall override. in any contingency which will cause the inter- est paid or agreed to be paid to exceed the maximum rate permitted by law, such excess will be applied to the reduction of any principal amount due, or if there is no principal amount due, shall be refunded. (4) title and delivery: title to goods ordered by buyer and risk of loss or damage in transit or thereafter shall pass to buyer upon supplier's delivery of the goods at supplier's plant or to a common carrier for shipment to buyer. (5) contingencies: supplier shall not be responsible for any failure to perform due to causes reasonably beyond its con- trol. these causes shall include, but not be restricted to, fire, storm, flood, earthquake, explosion, accident, acts of public enemy, war rebellion, insurrection, sabotage, epidemic, quarantine restrictions, labor disputes, labor shortages, labor slow downs and sit downs, transportation embargoes, failure or delays in transportation, inability to secure raw materials or machinery for the manufacture of its devices, acts of god, acts of the federal government or any agency thereof, acts of any state or local government or agency thereof, and judi- cial action. similar causes shall excuse buyer for failure to take goods ordered by buyer, from the time supplier receives written notice from buyer and for as long as the dis- abling cause continues, other than for goods already in tran- sit or specially fabricated and not readily saleable to other buyers. supplier assumes no responsibility for any tools, dies, and other equipment furnished supplier by buyer. (6) limited warranty and exclusive remedy: supplier warrants all catalog products to be free from defects in mate- rials and workmanship under normal and proper use and application for a period of twelve (12) months from the date code on the product in question (or if none, from the date of delivery to buyer.) with respect to products assembled, pre- pared, or manufactured to buyer's specifications, supplier warrants only that such products will meet buyer's specifica- tions upon delivery. as the party responsible for the specifi- cations, buyer shall be responsible for testing and inspecting the products for adherence to specifications, and supplier shall have no liability in the absence of such testing and inspection or if the product passes such testing or inspec- tion. the above warranty is the only warranty extended by supplier, and is in lieu of and excludes all other warranties and condi- tions, expressed or implied (except as pro- vided herein as to title), on any goods or services sold or rendered by supplier, includ- ing any implied warranties of merchantability and fitness for a particular purpose. this warranty will not create warranty coverage for any item into which any product sold by supplier may have been incorporated or added.
?2002 teccor electronics p - 11 http://www.teccor.com thyristor product catalog +1 972-580-7777 standard terms and conditions supplier's entire liability and buyer's exclu- sive remedy under this warranty shall be, at supplier's option, either the replacement of, repair of, or issuance of credit to buyer's account with supplier for any products which are properly returned by buyer during the warranty period. all returns must comply with the following conditions: (a) supplier is to be promptly notified in writing upon discov- ery of defects by buyer. (b) buyer must obtain a return material authorization (rma) number from the supplier prior to returning prod- uct. (c) the defective product is returned to supplier, transporta- tion charges prepaid by buyer. (d) supplier's examination of such product discloses, to its satisfaction, that such defects have not been caused by misuse, neglect, improper installation, repair, alteration, or accident. (e) the product is returned in the form it was delivered with any necessary disassembly carried out by buyer at buyer's expense. in no event shall supplier, or anyone else associated in the creation of any of supplier's products or services, be liable to buyer for incidental or consequential damages of any nature including loss of profits, loss of use, business interuption, and the like. buyer acknowledges that the above warranties and limitations thereon are appropriate and rea- sonable in effectuating supplier's and buyer's mutual intention to conduct an efficient transaction at prices more advantageous to buyer than would be available in the presence of other warranties and assurances. (7) patents: buyer shall notify supplier in writing of any claim that any product or any part of use thereof furnished under this agreement constitutes an infringement of any u.s. patent, copyright, trade secret, or other proprietary rights of a third party. notice shall be given within a reasonable period of time which should in most cases be within ten (10) days of receipt by buyer of any letter, summons, or complaint per- taining to such a claim. at its option, supplier may defend at its expense any action brought against buyer to the extent that it is based on such a claim. should supplier choose to defend any such claim, supplier may fully participate in the defense, settlement, or appeal of any action based on such claim. should any product become, or in supplier's opinion be likely to become, the subject of an action based on any such claim, supplier may, at its option, as the buyer's exclusive remedy, either procure for the buyer the right to continue using the product, replace the product or modify the product to make it noninfringing. in no event shall supplier be liable for any incidental or consequential damages based on any claim of infringement. supplier shall have no liability for any claim based on modifi- cations of a product made by any person or entity other than supplier, or based on use of a product in conjunction with any other item, unless expressly approved by supplier. sup- plier does not warrant goods against claims of infringement which are assembled, prepared, or manufactured to buyer's specifications. (8) non-waiver of default: each shipment made under any order shall be treated as a separate transaction, but in the event of any default by buyer, supplier may decline to make further shipments without in any way affecting its rights under such order. if, despite any default by buyer, supplier elects to continue to make shipments, its action shall not constitute a waiver of that or any default by buyer or in any way affect supplier's legal remedies for any such default. at any time, supplier's failure to exercise any right to remedy available to it shall not constitute a waiver of that right or remedy. (9) termination: if the products to be furnished under this order are to be used in the performance of a government contract or subcontract, and the government terminates such contract in whole or part, this order may be canceled to the extent it was to be used in the canceled portion of said government contract and the liability of buyer for termination allowances shall be determined by the then applicable regu- lations of the government regarding termination of contracts. supplier may cancel any unfilled orders unless buyer shall, upon written notice, immediately pay for all goods delivered or shall pay in advance for all goods ordered but not deliv- ered, or both, at supplier's option. (10) law: the validity, performance and construction of these terms and conditions and any sale made hereunder shall be governed by the laws of the state of texas. (11) assigns: this agreement shall not be assignable by either supplier or buyer. however, should either supplier or buyer be sold or transferred in its entirety and as an ongoing business, or should supplier or buyer sell or transfer in its entirety and as an ongoing concern, any division, depart- ment, or subsidiary responsible in whole or in part for the performance of this agreement, this agreement shall be binding upon and inure to the benefit of those successors and assigns of supplier, buyer, or such division, department, or subsidiary. (12) modification of standard terms and condi- tions: no attempted or suggested modification of or addi- tion to any of the provisions upon the face or reverse of this form, whether contained or arising in correspondence and/or documents passing between supplier and buyer, in any course of dealing between supplier or buyer, or in any cus- tomary usage prevalent among businesses comparable to those of supplier and/or buyer, shall be binding upon sup- plier unless made and agreed to in writing and signed by an officer of supplier. (13) quantities: any variation in quantities of electronic com- ponents, or other goods shipped over or under the quantities ordered (not to exceed 5%) shall constitute compliance with buyer's order and the unit pr ice will continue to apply.
notes
?2002 teccor electronics http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets e0 v-i characteristics of thyristor devices - - - - - - - - - - - - - - - - - - - - - e0-2 electrical parameter terminology - - - - - - - - - - - - - - - - - - - - - - - - - e0-3 sensitive triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e1 triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e2 quadracs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e3 alternistor triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e4 sensitive scrs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e5 scrs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e6 rectifiers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e7 diacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e8 sidac - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - e9
http://www.teccor.com e0 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog v-i characteristics of thyristor devices v-i characteristics of triac device v-i characteristics of scr device v-i characteristics of sidac device with negative resistance v-i characteristics of bilateral trigger diac breakover voltage specified minimum off-state blocking voltage (v drm ) +i -i +v -v minimum holding current (i h ) voltage drop (v t ) at specified current (i t ) latching current (i l ) off-state leakage current ? (i drm ) at specified v drm reverse breakdown voltage forward breakover voltage specified minimum off - state blocking voltage (v drm ) +i -i +v -v minimum holding current (i h ) voltage drop (v t ) at specified current (i t ) latching current (i l ) off - state leakage current - (i drm ) at specified v drm specified minimum reverse blocking voltage (v rrm ) reverse leakage current - (i rrm ) at specified v rrm -v +i v drm +v v s i s i h r s i drm i bo v bo v t i t (i s - i bo ) (v bo - v s ) r s = -i +i -i 10 ma +v -v breakover current i bo breakover voltage v bo ? v
?2002 teccor electronics e0 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 electrical parameter terminology thyristor di/dt (critical rate-of-rise of on-state current) ? maximum value of the rate-of-rise of on-state current which a thyristor can withstand without deleterious effect dv/dt (critical rate-of-rise of off-state voltage or static dv/dt) ? minimum value of the rate-of-rise of principal voltage which will cause switching from the off state to the on state dv/dt(c) critical rate-of-rise of commutation voltage of a triac (commutating dv/dt) ? minimum value of the rate-of-rise of principal voltage which will cause switching from the off state to the on state immediately following on-state current conduction in the opposite quadrant i 2 t (rms surge (non-repetitive) on-state fusing current) ? measure of let-through energy in terms of current and time for fusing purposes i bo (breakover current) ? principal current at the breakover point i drm (repetitive peak off-state current) ? maximum leakage current that may occur under the conditions of v drm i gt (gate trigger current) ? minimum gate current required to switch a thyristor from the off state to the on state i h (holding current) ? minimum principal current required to maintain the thyristor in the on state i pp (peak pulse current) ? peak pulse current at a short time duration and specified waveshape i rrm (repetitive peak reverse current) ? maximum leakage current that may occur under the conditions of v rrm i s (switching current) ? current at v s when a sidac switches from the clamping state to on state i t(rms) (on-state current) ? anode cathode principal current that may be allowed under stated conditions, usually the full- cycle rms current i tsm (surge (non-repetitive) on-state current) ? peak single cycle ac current pulse allowed p g(av) (average gate power dissipation) ? value of gate power which may be dissipated between the gate and main ter- minal 1 (or cathode) average over a full cycle p gm (peak gate power dissipation) ? maximum power which may be dissipated between the gate and main terminal 1 (or cathode) for a specified time duration r ja (thermal resistance, junction-to-ambient) ? tempera- ture difference between the thyristor junction and ambient divided by the power dissipation causing the temperature difference under conditions of thermal equilibrium note : ambient is defined as the point where temperature does not change as a result of the dissipation. r jc (thermal resistance, junction-to-case) ? temperature difference between the thyristor junction and the thyristor case divided by the power dissipation causing the temperature differ- ence under conditions of thermal equilibrium t gt (gate-controlled turn-on time) ? time interval between the 10% rise of the gate pulse and the 90% rise of the principal current pulse during switching of a thyristor from the off state to the on state t q (circuit-commutated turn-off time) ? time interval between the instant when the principal current has decreased to zero after external switching of the principal voltage circuit and the instant when the scr is capable of supporting a specified principal voltage without turning on v bo (breakover voltage) ? principal voltage at the breakover point v drm (repetitive peak off-state voltage) ? maximum allow- able instantaneous value of repetitive off-state voltage that may be applied across a bidirectional thyristor (forward or reverse direction) or scr (forward direction only) v gt (gate trigger voltage) ? minimum gate voltage required to produce the gate trigger current v rrm (repetitive peak reverse voltage) ? maximum allow- able instantaneous value of a repetitive reverse voltage that may be applied across an scr without causing reverse current ava- lanche v s (switching voltage) ? voltage point after v bo when a sidac switches from a clamping state to on state v t (on-state voltage) ? principal voltage when the thyristor is in the on state diode rectifiers i f(av) (average forward current) ? average forward conduc- tion current i fm (maximum (peak) reverse current) ? maximum reverse leakage current that may occur at rated v rrm i f(rms) (rms forward current) ? rms forward conduction cur- rent i fsm (maximum (peak) forward (non-repetitive) surge current) ? maximum (peak) forward single cycle ac surge cur- rent allowed for specified duration v fm (maximum (peak) forward voltage drop) ? maximum (peak) forward voltage drop from the anode to cathode at stated conditions v r (reverse blocking voltage) ? maximum allowable dc reverse blocking voltage that may be applied to the rectifier v rrm (maximum (peak) repetitive reverse voltage) ? maxi- mum peak allowable value of a repetitive reverse voltage that may be applied to the rectifier
notes
?2002 teccor electronics e1 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 selected package s* u.l. recogn ized file #e71639 mt2 mt1 g sensitive triacs (0.8 a to 8 a) e1 general description teccor's line of sensitive gate triacs includes devices with current capabilities through 8 a. voltage ranges are available from 200 v to 600 v. this line features devices with guaranteed gate control in quadrants ii and iv as well as control in the commonly used quadrants i and iii. four-quadrant control devices require sensitive gate triacs. they can be controlled by digital circuitry where positive-only or negative-only pulses must control ac current in both directions through the device. note that triacs with low i gt values in quadrants ii and iv will have lower dv/dt characteristics. the sensitive gate triac is a bidirectional ac switch and is gate controlled for either polarity of main terminal voltage. it is used primarily for ac switching and phase control applications such as motor speed controls, temperature modulation controls, and lighting controls. the epoxy to-92 and to-220 configurations feature teccor's electrically-isolated construction where the case or mounting tab is internally isolated from the semiconductor chip and lead attachments. non-isolated epoxy to-202 packages are available as well as to-251 and surface mount to-252 (d-pak). tape- and-reel capability and tube packing also are available. see ?packing options? section of this catalog. all teccor triacs have glass-passivated junctions. this glassing process prevents migration of contaminants and ensures long- term device reliability with parameter stability. variations of devices covered in this data sheet are available for custom design applications. consult factory for more information. features ? electrically-isolated packages ? glass-passivated junctions ensure long device reliability and parameter stability ? voltage capability ? up to 600 v ? surge capability ? up to 80 a ? four-quadrant gating guaranteed compak sensitive gate triac ? surface mount package ? 0.8 a and 1 a series ? new small profile three-leaded compak package ? packaged in embossed carrier tape with 2,500 devices per reel ? can replace sot-223 to-202 to-92 3-lead compak * to-220 isolated e1 to-252 d-pak to-251 v-pak
sensitive triacs data sheets http://www.teccor.com e1 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog see ?general notes? on page e1 - 4 and ?electrical specification notes? on page e1 - 5. i t(rms) part no. v drm i gt i drm isolated non-isolated (11) to-92 compak to-220 to-252 d-pak to-202 to-251 v-pak (1) volts (3) (6) (9) mamps (1) (14) mamps qi qii qiii qiv t c = 25 c t c = 110 c max see ?package dimensions? section for variations. (12) min max max 0.8 a l2x8e3 l2x3 200 3 3 3 3 0.01 0.1 l4x8e3 l4x3 400 3 3 3 3 0.01 0.1 l6x8e3 l6x3 600 3 3 3 3 0.01 0.1 l2x8e5 l2x5 200 5 5 5 5 0.01 0.1 l4x8e5 l4x5 400 5 5 5 5 0.01 0.1 l6x8e5 l6x5 600 5 5 5 5 0.01 0.1 l2x8e6 200 5 5 5 10 0.01 0.1 l4x8e6 400 5 5 5 10 0.01 0.1 l6x8e6 600 5 5 5 10 0.01 0.1 l2x8e8 200 10 10 10 20 0.01 0.1 l4x8e8 400 10 10 10 20 0.01 0.1 l6x8e8 600 10 10 10 20 0.01 0.1 1a l201e3 l2n3 200 33330.010.1 l401e3 l4n3 400 33330.010.1 l601e3 l6n3 600 33330.010.1 l201e5 l2n5 200 55550.010.1 l401e5 l4n5 400 55550.010.1 l601e5 l6n5 600 55550.010.1 l201e6 200 5 5 5 10 0.01 0.1 l401e6 400 5 5 5 10 0.01 0.1 l601e6 600 5 5 5 10 0.01 0.1 l201e8 200 10101020 0.01 0.1 l401e8 400 10101020 0.01 0.1 l601e8 600 10101020 0.01 0.1 4a l2004l3 l2004d3 l2004f31 l2004v3 200 3 3 3 3 0.01 0.2 l4004l3 l4004d3 l4004f31 l4004v3 400 3 3 3 3 0.01 0.2 l6004l3 l6004d3 l6004f31 l6004v3 600 3 3 3 3 0.01 0.2 l2004l5 l2004d5 l2004f51 l2004v5 200 5 5 5 5 0.01 0.2 l4004l5 l4004d5 l4004f51 l4004v5 400 5 5 5 5 0.01 0.2 l6004l5 l6004d5 l6004f51 l6004v5 600 5 5 5 5 0.01 0.2 l2004l6 l2004d6 l2004f61 l2004v6 200 5 5 5 10 0.01 0.2 l4004l6 l4004d6 l4004f61 l4004v6 400 5 5 5 10 0.01 0.2 l6004l6 l6004d6 l6004f61 l6004v6 600 5 5 5 10 0.01 0.2 l2004l8 l2004d8 l2004f81 l2004v8 200 10 10 10 20 0.01 0.2 l4004l8 l4004d8 l4004f81 l4004v8 400 10 10 10 20 0.01 0.2 l6004l8 l6004d8 l6004f81 l6004v8 600 10 10 10 20 0.01 0.2 mt1 g mt2 mt2 mt1 g mt1 mt2 g mt2 mt2 mt1 g mt1 g mt2 mt2 mt2 mt2 g mt1
data sheets sensitive triacs ?2002 teccor electronics e1 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 see ?general notes? on page e1 - 4 and ?electrical specification notes? on page e1 - 5. v tm v gt i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (4) volts (2) (5) (15) volts (1) (7) mamps (13) amps (13) watts watts (8) (10) amps (1) (10) volts/sec (1) volts/ sec (9) sec amps 2 sec amps/sec t c = 25 c t c = 25 c60/50hz t c = 100 c max max max typ typ typ 1.6 2 5 1 10 0.2 10/8.3 0.5 20 2.8 0.41 20 1.6 2 5 1 10 0.2 10/8.3 0.5 15 2.8 0.41 20 1.6 2 5 1 10 0.2 10/8.3 0.5 10 2.8 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 20 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 15 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 10 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 30 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 25 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 20 3 0.41 20 1.6 2 15 1 10 0.2 10/8.3 2 35 3.2 0.41 20 1.6 2 15 1 10 0.2 10/8.3 2 30 3.2 0.41 20 1.6 2 15 1 10 0.2 10/8.3 2 25 3.2 0.41 20 1.625110 0.220/16.70.5 202.81.6 20 1.625110 0.220/16.70.5 202.81.6 20 1.625110 0.220/16.70.5 102.81.6 20 1.6 2 10 1 10 0.2 20/16.7 1 20 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 20 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 10 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 30 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 30 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 20 3 1.6 20 1.6 2 15 1 10 0.2 20/16.7 1 35 3.2 1.6 20 1.6 2 15 1 10 0.2 20/16.7 1 35 3.2 1.6 20 1.6 2 15 1 10 0.2 20/16.7 1 25 3.2 1.6 20 1.6 2 5 1.2 15 0.3 40/33 0.5 25 2.8 6.6 50 1.6 2 5 1.2 15 0.3 40/33 0.5 25 2.8 6.6 50 1.6 2 5 1.2 15 0.3 40/33 0.5 15 2.8 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 25 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 25 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 15 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 30 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 30 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 20 3 6.6 50 1.6 2 15 1.2 15 0.3 40/33 2 35 3.2 6.6 50 1.6 2 15 1.2 15 0.3 40/33 2 35 3.2 6.6 50 1.6 2 15 1.2 15 0.3 40/33 2 25 3.2 6.6 50
sensitive triacs data sheets http://www.teccor.com e1 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog specified test conditions di/dt ? maximum rate-of-change of on-state current; i gt = 50 ma with 0.1 s rise time dv/dt ? critical rate-of-rise of off-state voltage at rated v drm gate open dv/dt(c) ? critical rate-of-rise of commutation voltage at rated v drm and i t(rms) commutating di/dt = 0.54 rated i t(rms) /ms; gate unenergized i 2 t ? rms surge (non-repetitive) on-st ate current for period of 8.3 ms for fusing i drm ? peak off-state current, gate open; v drm = max rated value i gt ? dc gate trigger current in specific operating quadrants; v d = 12 v dc; r l = 60 ? i gtm ? peak gate trigger current i h ? holding current gate open; initial on-state current = 100 ma dc i t(rms) ? rms on-state current conduction angle of 360 i tsm ? peak one-cycle surge p g(av) ? average gate power dissipation p gm ? peak gate power dissipation; i gt i gtm t gt ? gate controlled turn-on time; i gt = 50 ma with 0.1 s rise time v drm ? repetitive peak off-state/blocking voltage v gt ? dc gate trigger voltage; v d = 12 v dc; r l = 60 ? v tm ? peak on-state voltage at max rated rms current general notes ? all measurements are made with 60 hz resistive load and at an ambient temperature of +25 c unless otherwise specified. ? operating temperature range (t j ) is -65 c to +110 c for to-92 devices and -40 c to 110 c for all other devices. ? storage temperature range (t s ) is -65 c to +150 c for to-92 devices, -40 c to +150 c for to-202 devices, and -40 c to +125 c for to-220 devices. ? lead solder temperature is a maximum of 230 c for 10 seconds maximum at a minimum of 1/16? (1.59 mm) from case. ? the case or lead temperature (t c or t l ) is measured as shown on dimensional outline drawings. see ?package dimensions? section of this catalog. i t(rms) part no. v drm i gt i drm isolated non-isolated (11) to-220 to-252 d-pak to-251 v-pak (1) volts (3) (6) mamps (1) (14) mamps qi qii qiii qiv t c = 25 c t c = 110 c max see ?package dimensions? section for variations. (12) min max max 6a l2006l5 l2006d5 l2006v5 200 5555 0.02 0.5 l4006l5 l4006d5 l4006v5 400 5555 0.02 0.5 l6006l5 l6006d5 l6006v5 600 5555 0.02 0.5 l2006l6 l2006d6 l2006v6 200 5 5 5 10 0.02 0.5 l4006l6 l4006d6 l4006v6 400 5 5 5 10 0.02 0.5 l6006l6 l6006d6 l6006v6 600 5 5 5 10 0.02 0.5 l2006l8 l2006d8 l2006v8 200 10 10 10 20 0.02 0.5 l4006l8 l4006d8 l4006v8 400 10 10 10 20 0.02 0.5 l6006l8 l6006d8 l6006v8 600 10 10 10 20 0.02 0.5 8a l2008l6 l2008d6 l2008v6 200 5 5 5 10 0.02 0.5 l4008l6 l4008d6 l4008v6 400 5 5 5 10 0.02 0.5 l6008l6 l6008d6 l6008v6 600 5 5 5 10 0.02 0.5 l2008l8 l2008d8 l2008v8 200 10 10 10 20 0.02 0.5 l4008l8 l4008d8 l4008v8 400 10 10 10 20 0.02 0.5 l6008l8 l6008d8 l6008v8 600 10 10 10 20 0.02 0.5 mt1 mt2 g mt2 mt2 mt1 g mt2 mt2 g mt1
data sheets sensitive triacs ?2002 teccor electronics e1 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 electrical specification notes (1) for either polarity of mt2 with reference to mt1 terminal (2) for either polarity of gate voltage v gt with reference to mt1 terminal (3) see gate characteristics and definition of quadrants. (4) see figure e1.4 for i t versus v t . (5) see figure e1.6 for v gt versus t c . (6) see figure e1.7 for i gt versus t c . (7) see figure e1.5 for i h versus t c . (8) see figure e1.9 for surge rating and specific duration. (9) see figure e1.8 for t gt versus i gt . (10) see figure e1.2 and figure e1.3 for maximum allowable case temperature at maximum rated current. (11) see figure e1.1, figure e1.2, and figure e1.3 for t a or t c versus i t(rms) . (12) see package outlines for lead fo rm configurations. when ordering special lead forming, add type number as suffix to part number. (13) pulse width 10 s (14) t c or t l = t j for test conditions in off state (15) minimum non-trigger v gt at 110 c is 0.2 v. gate characteristics teccor triacs may be turned on between gate and mt1 terminals in the following ways: ? in-phase signals (with standard ac line) using quadrants i and iii ? application of unipolar pulses (gate always positive or nega- tive), using quadrants ii and iii with negative gate pulses and quadrants i and iv with positive gate pulses when maximum surge capability is required, pulses should be a minimum of one magnitude above i gt rating with a steep rising waveform ( 1 s rise time). definition of quadrants v tm v gt i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (4) volts (2) (5) (15) volts (1) (7) mamps (13) amps (13) watts watts (8) (10) amps (1) (10) volts/sec (1) volts/sec (9) sec amps 2 sec amps/sec t c = 25 c t c = 25 c 60/50 hz t c = 100 c max max max typ typ typ 1.6 2 10 1.6 18 0.4 60/50 1 40 3 15 70 1.6 2 10 1.6 18 0.4 60/50 1 30 3 15 70 1.6 2 10 1.6 18 0.4 60/50 1 20 3 15 70 1.6 2 10 1.6 18 0.4 60/50 2 40 3 15 70 1.6 2 10 1.6 18 0.4 60/50 2 30 3 15 70 1.6 2 10 1.6 18 0.4 60/50 2 20 3 15 70 1.6 2 20 1.6 18 0.4 60/50 2 45 3.2 15 70 1.6 2 20 1.6 18 0.4 60/50 2 40 3.2 15 70 1.6 2 20 1.6 18 0.4 60/50 2 30 3.2 15 70 1.6 2 10 1.6 18 0.4 80/65 2 40 3 26.5 70 1.6 2 10 1.6 18 0.4 80/65 2 30 3 26.5 70 1.6 2 10 1.6 18 0.4 80/65 2 20 3 26.5 70 1.6 2 20 1.6 18 0.4 80/65 2 45 3.2 26.5 70 1.6 2 20 1.6 18 0.4 80/65 2 40 3.2 26.5 70 1.6 2 20 1.6 18 0.4 80/65 2 30 3.2 26.5 70 mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + -
sensitive triacs data sheets http://www.teccor.com e1 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog electrical isolation teccor?s isolated triac packages withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab over the device's operating temperature range. the following isolation table shows standard isolation ratings. * ul recognized file #e71639 * mounted on 1 cm 2 copper foil surface; two-ounce copper foil figure e1.1 maximum allowable ambient temperature versus on-state current figure e1.2 maximum allowable case temperature versus on-state current (0.8 a and 1 a) electrical isolation from leads to mounting tab vacrms to-220 * 2500 standard thermal resistance (steady state) junction to mounting tab and junction to ambient r jc [r ja ] c/w (typ) package code ecflf2dv type to-92 plastic compak to-202 type 1 to-220 isolated to-202 type 2 to-252 d-pak to-251 v-pak 0.8 a 60 [135] 60 * 1 a 50 [95] 40 * 4a 3.5 [45] 3.6 [50] 6.0 [70] 3.5 6.0 [70] 6a 3.3 3.2 3.2 8a 2.8 2.7 2.7 20 40 60 80 100 120 rms on-state current [i t(rms) ] - amps maximum allowable ambient temperature ( t a ) - ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? free air rating ? no heatsink to-220 and type 1 and 3 to-202 type 2 and 4 to-202 and to-251 0.8 a to-92 1 a to-92 25 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 50 60 70 80 90 100 110 maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawings rms on-state current [i t(rms) ] ? amps 1 a 0.8 a
data sheets sensitive triacs ?2002 teccor electronics e1 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e1.3 maximum allowable case temperature versus on-state current (4 a, 6 a, and 8 a) figure e1.4 on-state current versus on-state voltage (typical) figure e1.5 normalized dc holding current versus case temperature figure e1.6 normalized dc gate trigger voltage for all quadrants versus case temperature figure e1.7 normalized dc gate trigger current for all quadrants versus case temperature figure e1.8 turn-on time versus gate trigger current (typical) 01 23 4 5 6 7 8 60 65 70 75 80 85 90 95 100 105 110 rms on-state current [i t(rms) ] - amps maximum allowable case temperature ( t c ) - ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawings 4 a type 1 and 3 to-202 4 a to-220 (isolated) 4 a to-252 8 a to-220 (isolated) 6 a to-220 (isolated) 4 a type 2 and 4 to-202 4 a to-251 8 a to-251 and to-252 6 a to-251 6 a to-252 0 0.5 0.8 1.0 1.2 1.4 1.6 1.8 0 2 4 6 8 10 12 14 16 18 20 positive or negative instantaneous on-state voltage (v t ) - volts positive or negative instantaneous on-state current (i t ) - amps 1 a 4 a 6 a and 8 a t c = 25 ? c 0.8 a -40 -15 +25 +65 +110 +125 0 1.0 2.0 3.0 4.0 -65 case temperature ( t c ) - ? c initial on-state current = 100 ma (dc) 0.8 - 4 a devices = 200 ma (dc) 6 - 8 a devices ratio of i h i h (t c = 25 ? c) -65 -40 -15 +65 +110 +125 +25 0 .5 1.0 1.5 2.0 ratio of v gt v gt (t c = 25 ?c) case temperature ( t c ) - ? c -65 -40 -15 +65 +110 +125 +25 0 1.0 2.0 3.0 4.0 ratio of i gt i gt (t c = 25 ?c) case temperature (t c ) - ?c 12346 5 8 10 20 30 40 60 80 100 i gt = 5 ma max i gt = 10 ma max i gt = 20 ma max i gt = 3 ma max 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 dc gate trigger current (i gt ) - ma turn-on time (t gt ) - sec t c = 25 ?c
sensitive triacs data sheets http://www.teccor.com e1 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e1.9 peak surge current versus surge current duration figure e1.10 power dissipation (typical) versus rms on-state current (0.8 a and 1 a) figure e1.11 power dissipation (typical) versus rms on-state current (4 a, 6 a, and 8 a) 1 24 368102040 30 60 100 200 400 600 1000 1 2 3 4 6 10 8 20 30 40 60 100 80 150 200 surge current duration ? full cycles peak surge (non-repetitive) on-state current (i tsm ) ? amps 8 a 6 a 0.8 a supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: maximum rated value at specified case temperature notes: 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. 1 a 4 a 0 0.25 0.50 0.75 1.0 1.25 1.5 0 0.5 1.0 1.5 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 1 a 0.8 a 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 8.0 6 a and 8 a 4 a rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ?
?2002 teccor electronics e2 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 selected package s* u.l. recogn ized file #e71639 triacs (0.8 a to 35 a) e2 general description these gated triacs from teccor electronics are part of a broad line of bidirectional semiconductors. the devices range in current ratings from 0.8 a to 35 a and in voltages from 200 v to 1000 v. the triac may be gate triggered from a blocking to conduction state for either polarity of applied voltage and is designed for ac switching and phase control applications such as speed and tem- perature modulation controls, lighting controls, and static switch- ing relays. the triggering signal is normally applied between the gate and mt1. isolated packages are offered with internal construction, having the case or mounting tab electrically isolated from the semicon- ductor chip. this feature facilitates the use of low-cost assembly and convenient packaging techniques. tape-and-reel capability is available. see ?packing options? section of this catalog. all teccor triacs have glass-passivated junctions to ensure long- term device reliability and parameter stability. teccor's glass-pas- sivated junctions offer a rugged, reliable barrier against junction contamination. variations of devices covered in this data sheet are available for custom design applications. consult factory for more information. features ? electrically-isolated packages ? glass-passivated junctions ? voltage capability ? up to 1000 v ? surge capability ? up to 200 a compak package ? surface mount package ? 0.8 a and 1 a series ? new small profile three-leaded compak package ? packaged in embossed carrier tape with 2,500 devices per reel ? can replace sot-223 e2 mt2 mt1 g to-202 * to-220 3-lead compak to-92 to-251 v-pak to-263 d 2 pak to-92 to-252 d-pak * to-3 fastpak
triacs data sheets http://www.teccor.com e2 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog see ?general notes? on page e2 - 4 and ?electrical specification notes? on page e2 - 5. i t(rms) part number v drm i gt isolated non-isolated (4) to-92 to-220 compak to-202 to-220 to-252 d-pak to-251 v-pak to-263 d 2 pak (1) volts (3) (7) (15) mamps qi qii qiii qiv qiv max see ?package dimensions? section for variations. (11) min max typ 0.8 a q2x8e3 q2x3 200 10 10 10 25 q4x8e3 q4x3 400 10 10 10 25 q6x8e3 q6x3 600 10 10 10 25 q2x8e4 q2x4 200 25 25 25 50 q4x8e4 q4x4 400 25 25 25 50 q6x8e4 q6x4 600 25 25 25 50 1a q201e3 q2n3 200 101010 25 q401e3 q4n3 400 101010 25 q601e3 q6n3 600 101010 25 q201e4 q2n4 200 252525 50 q401e4 q4n4 400 252525 50 q601e4 q6n4 600 252525 50 4a q2004l3 q2004f31 q2004d3 q2004v3 200 10 10 10 25 q4004l3 q4004f31 q4004d3 q4004v3 400 10 10 10 25 q6004l3 q6004f31 q6004d3 q6004v3 600 10 10 10 25 q2004l4 q2004f41 q2004d4 q2004v4 200 25 25 25 50 q4004l4 q4004f41 q4004d4 q4004v4 400 25 25 25 50 q6004l4 q6004f41 q6004d4 q6004v4 600 25 25 25 50 q8004l4 q8004d4 q8004v4 800 25 25 25 50 qk004l4 qk004d4 qk004v4 1000 25 25 25 50 6a q2006l4 q2006f41 q2006r4 q2006n4 200 25 25 25 50 q4006l4 q4006f41 q4006r4 q4006n4 400 25 25 25 50 q6006l5 q6006f51 q6006r5 q6006n5 600 50 50 50 75 q8006l5 q8006r5 q8006n5 800 50 50 50 75 qk006l5 qk006r5 qk006n5 1000 50 50 50 75 8a q2008l4 q2008f41 q2008r4 q2008n4 200 25 25 25 50 q4008l4 q4008f41 q4008r4 q4008n4 400 25 25 25 50 q6008l5 q6008f51 q6008r5 q6008n5 600 50 50 50 75 q8008l5 q8008r5 q8008n5 800 50 50 50 75 qk008l5 qk008r5 qk008n5 1000 50 50 50 75 mt1 g mt2 mt1 mt2 g g mt1 mt2 mt2 mt1 g mt2 mt1 g mt2 mt2 mt2 mt2 mt1 g mt2 mt2 g mt1 mt2 mt2 mt1 g
data sheets triacs ?2002 teccor electronics e2 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 see ?general notes? on page e2 - 4 and ?electrical specification notes? on page e2 - 5. i drm v tm v gt i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (16) mamps (1) (5) volts (2) (6) (15) (18) (19) volts (1) (8) (12) mamps (14) amps (14) watts watts (9) (13) amps (1) (4) (13) volts/sec (1) volts/ sec (10) sec amp 2 sec amps/sec t c = 25 c t c = 100 c t c = 125 c t c = 25 c t c = 25 c 60/50 hz t c = 100 c t c = 125 c max max max max typ min typ 0.02 0.5 1 1.6 2 15 1 10 0.2 10/8.3 1 40 30 2.5 0.41 20 0.02 0.5 1 1.6 2 15 1 10 0.2 10/8.3 1 35 25 2.5 0.41 20 0.02 0.5 1 1.6 2 15 1 10 0.2 10/8.3 1 25 15 2.5 0.41 20 0.02 0.5 1 1.6 2.5 25 1 10 0.2 10/8.3 1 50 40 3 0.41 20 0.02 0.5 1 1.6 2.5 25 1 10 0.2 10/8.3 1 45 35 3 0.41 20 0.02 0.5 1 1.6 2.5 25 1 10 0.2 10/8.3 1 35 25 3 0.41 20 0.02 0.5 1 1.6 2 15 1 10 0.2 20/16.7 1 40 30 2.5 1.6 30 0.02 0.5 1 1.6 2 15 1 10 0.2 20/16.7 1 40 30 2.5 1.6 30 0.02 0.5 1 1.6 2 15 1 10 0.2 20/16.7 1 30 20 2.5 1.6 30 0.02 0.5 1 1.6 2.5 25 1 10 0.2 20/16.7 1 50 40 3 1.6 30 0.02 0.5 1 1.6 2.5 25 1 10 0.2 20/16.7 1 50 40 3 1.6 30 0.02 0.5 1 1.6 2.5 25 1 10 0.2 20/16.7 1 40 30 3 1.6 30 0.05 0.5 2 1.6 2 20 1.2 15 0.3 55/46 2 50 40 2.5 12.5 50 0.05 0.5 2 1.6 2 20 1.2 15 0.3 55/46 2 50 40 2.5 12.5 50 0.05 0.5 2 1.6 2 20 1.2 15 0.3 55/46 2 40 30 2.5 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 100 75 3 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 100 75 3 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 75 50 3 12.5 50 0.05 0.5 2 1.6 2.5 30 1.2 15 0.3 55/46 2 60 40 3 12.5 50 0.05 3 1.6 2.5 30 1.2 15 0.3 55/46 2 50 3 12.5 50 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 200 120 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 200 120 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 150 100 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.6 18 0.5 80/65 4 125 85 3 26.5 70 0.05 3 1.6 2.5 50 1.6 18 0.5 80/65 4 100 3 26.5 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 250 150 3 41 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 250 150 3 41 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 220 125 3 41 70 0.05 0.5 2 1.6 2.5 50 1.8 20 0.5 100/83 4 150 100 3 41 70 0.05 3 1.6 2.5 50 1.8 20 0.5 100/83 4 100 3 41 70
triacs data sheets http://www.teccor.com e2 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog specific test conditions di/dt ? maximum rate-of-change of on-state current; i gt = 200 ma with 0.1 s rise time dv/dt ? critical rate-of-rise of off-state voltage at rated v drm gate open dv/dt(c) ? critical rate-of-rise of commutation voltage at rated v drm and i t(rms) commutating di/dt = 0.54 rated i t(rms) /ms; gate unenergized i 2 t ? rms surge (non-repetitive) on-st ate current for period of 8.3 ms for fusing i drm ? peak off-state current, gate open; v drm = maximum rated value i gt ? dc gate trigger current in specific operating quadrants; v d = 12 v dc i gtm ? peak gate trigger current i h ? holding current (dc); gate open i t(rms) ? rms on-state current conduction angle of 360 i tsm ? peak one-cycle surge p g(av) ? average gate power dissipation p gm ? peak gate power dissipation; i gt i gtm t gt ? gate controlled turn-on time; i gt = 200 ma with 0.1 s rise time v drm ? repetitive peak blocking voltage v gt ? dc gate trigger voltage; v d = 12 v dc; r l = 60 ? v tm ? peak on-state voltage at maximum rated rms current general notes ? all measurements are made at 60 hz with a resistive load at an ambient temperature of +25 c unless specified otherwise. ? operating temperature range (t j ) is -65 c to +125 c for to-92, -25 c to +125 c for fastpak, and -40 c to +125 c for all other devices. ? storage temperature range (t s ) is -65 c to +150 c for to-92, -40 c to +150 c for to-202, and -40 c to +125 c for all other devices. ? lead solder temperature is a maximum of 230 c for 10 seconds, maximum; 1/16" (1.59 mm) from case. ? the case temperature (t c ) is measured as shown on the dimen- sional outline drawings. see ?package dimensions? section of this catalog. i t(rms) part number v drm i gt i drm isolated non-isolated (4) (16) to-3 fastpak to-220 to-202 to-220 to-263 d 2 pak (1) volts (3) (7) (15) mamps (1) (16) mamps qi qii qiii qiv qiv t c = 25 c t c = 100 c t c = 125 c max see ?package dimensions? section for variations. (11) min max typ max 10 a q2010l4 q2010r4 q2010n4 200 25 25 25 50 0.05 1 q4010l4 q4010r4 q4010n4 400 25 25 25 50 0.05 1 q6010l4 q6010r4 q6010n4 600 25 25 25 50 0.05 1 q8010l4 q8010r4 q8010n4 800 25 25 25 50 0.1 1 qk010l4 qk010r4 qk010n4 1000 25 25 25 50 0.1 3 q2010l5 q2010f51 q2010r5 q2010n5 200 50 50 50 75 0.05 0.5 2 q4010l5 q4010f51 q4010r5 q4010n5 400 50 50 50 75 0.05 0.5 2 q6010l5 q6010f51 q6010r5 q6010n5 600 50 50 50 75 0.05 0.5 2 q8010l5 q8010r5 q8010n5 800 50 50 50 75 0.1 0.5 2 qk010l5 qk010r5 qk010n5 1000 50 50 50 75 0.1 3 15 a q2015l5 q2015r5 q2015n5 200 50 50 50 0.05 0.5 2 q4015l5 q4015r5 q4015n5 400 50 50 50 0.05 0.5 2 q6015l5 q6015r5 q6015n5 600 50 50 50 0.05 0.5 2 q8015l5 q8015r5 q8015n5 800 50 50 50 0.1 1 3 qk015l5 qk015r5 qk015n5 1000 50 50 50 0.1 3 25 a q2025r5 q2025n5 200 50 50 50 0.1 1 3 q4025r5 q4025n5 400 50 50 50 0.1 1 3 q6025r5 q6025n5 600 50 50 50 0.1 1 3 q8025r5 q8025n5 800 50 50 50 0.1 1 3 qk025r5 qk025n5 1000 50 50 50 0.1 3 q6025p5 600 505050 1200.1 5 q8025p5 800 505050 1200.1 5 35 a q6035p5 600 50 50 50 120 0.1 5 q8035p5 800 50 50 50 120 0.1 5 mt1 mt2 gate mt1 mt2 t mt2 mt1 g mt2 mt1 g mt2 mt2 mt2 mt2 mt1 g
data sheets triacs ?2002 teccor electronics e2 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 electrical specification notes (1) for either polarity of mt2 with reference to mt1 terminal (2) for either polarity of gate voltage (v gt ) with reference to mt1 terminal (3) see gate characteristics and definition of quadrants. (4) see figure e2.1 through figure e2.7 for current rating at specific operating temperature. (5) see figure e2.8 through figure e2.10 for i t versus v t . (6) see figure e2.12 for v gt versus t c . (7) see figure e2.11 for i gt versus t c . (8) see figure e2.14 for i h versus t c . (9) see figure e2.13 for surge rating with specific durations. (10) see figure e2.15 for t gt versus i gt . (11) see package outlines for lead form configurations. when ordering special lead forming, add type number as suffix to part number. (12) initial on-state current = 200 ma dc for 0.8 a to10 a devices, 400 ma dc for 15 a to 35 a devices (13) see figure e2.1 through figure e2.6 for maximum allowable case temperature at maximum rated current. (14) pulse width 10 s; i gt i gt m (15) r l = 60 ? for 0.8 a to10 a triacs; r l = 30 ? for 15 a to 35 a triacs (16) t c = t j for test conditions in off state (17) i gt = 300 ma for 25 a and 35 a devices (18) quadrants i, ii, iii only (19) minimum non-trigger v gt at 125 c is 0.2 v for all except 50 ma max qiv devices which are 0.2 v at 110 c. gate characteristics teccor triacs may be turned on between gate and mt1 terminals in the following ways: ? in-phase signals (with standard ac line) using quadrants i and iii ? application of unipolar pulses (gate always positive or nega- tive), using quadrants ii and iii with negative gate pulses and quadrants i and iv with positive gate pulses however, due to higher gate requirements for quadrant iv, it is recommended that only negative pulses be applied. if pos- itive pulses are required, see ?sensitive triacs? section of this catalog or contact the factory. also, see figure an1002.8, ?amplified gate? thyristor circuit. v tm v gt i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (5) volts (2) (6) (15) (18) (19) volts (1) (8) (12) mamps (14) amps (14) watts watts (9) (13) amps (1) (4) (13) volts/sec (1) volts/ sec (10) (17) sec amps 2 sec amps/sec t c = 25 c t c = 25 c 60/50 hz t c = 100 c t c = 125 c max max max typ min typ 1.6 2.5 35 1.8 20 0.5 120/100 2 150 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 150 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 100 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 75 3 60 70 1.6 2.5 35 1.8 20 0.5 120/100 2 50 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 350 225 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 350 225 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 300 200 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 250 175 3 60 70 1.6 2.5 50 1.8 20 0.5 120/100 4 150 3 60 70 1.6 2.5 70 2 20 0.5 200/167 4 400 275 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 400 275 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 350 225 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 300 200 4 166 100 1.6 2.5 70 2 20 0.5 200/167 4 200 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 400 275 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 400 275 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 350 225 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 300 200 4 166 100 1.8 2.5 100 2 20 0.5 200/167 5 200 4 166 100 1.4 2.75 50 2 20 0.5 250/220 5 550 475 3 260 100 1.4 2.75 50 2 20 0.5 250/220 5 450 400 3 260 100 1.5 2.75 50 2 20 0.5 350/300 5 550 475 3 508 100 1.5 2.75 50 2 20 0.5 350/300 5 450 400 3 508 100
triacs data sheets http://www.teccor.com e2 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog in all cases, if maximum surge capability is required, pulses should be a minimum of one magnitude above i gt rating with a steep rising waveform ( 1 s rise time). definition of quadrants electrical isolation teccor?s isolated triac packages will withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab or base, over the operating temperature range of the device. the following isolation table shows standard and optional isolation ratings. * ul recognized file e71639 ** for 4000 v isolation, use v suffix in part number. * mounted on 1 cm 2 copper foil surface; two-ounce copper foil mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - electrical isolation from leads to mounting tab * vacrms to-220 isolated fastpak isolated 2500 standard standard 4000 optional ** n/a thermal resistance (steady state) r jc [r ja ] (typ. ) c/w package code pecff2lr d v n type to-3 fastpak to-92 compak to-202 type 1 to-202 type 2 to-220 isolated to-220 non-isolated to-252 d-pak to-251 v-pak to-263 d 2 pak 0.8 a 60 [135] 60 * 1 a 50 [95] 40 * 4a 3.5 [45] 6 [70] 3.6 [50] 3.5 6.0 [70] 6 a 3.8 3.3 1.8 [45] 1.8 8a 3.3 2.8 1.5 1.5 10 a 3.5 2.6 1.3 1.3 15 a 2.1 1.1 1.1 25 a 1.6 0.89 0.89 35 a 1.5
data sheets triacs ?2002 teccor electronics e2 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e2.1 maximum allowable case temperature versus on-state current (0.8 a and 1 a) figure e2.2 maximum allowable case temperature versus on-state current (4 a and 6 a) figure e2.3 maximum allowable case temperature versus on-state current (8 a and 10 a) figure e2.4 maximum allowable case temperature versus on-state current (10 a) figure e2.5 maximum allowable case temperature versus on-state current (15 a) figure e2.6 maximum allowable case temperature versus on-state current (25 a and 35 a) 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ? c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 1 a 0.8 a 01234567 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ? c 6 a to-220 (isolated) 6 a to-202 6 a to-220 (non-isolated) 6 a d 2 pak 4 a to-220 (isolated) 4 a to-202 (type 1 and 3) 4 a to-252 current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 4 a to-202 (type 2 and 4) 4 a to-251 02468101214 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 10 a to-220 (isolated) 8 a to-220 (non-isolated) 8 a d 2 pak 8 a to-202 8 a to-220 (isolated) current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 02468101214 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 10 a to-202 10 a to-220 (non-isolated) 10 a d 2 pak 051015 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 15 a to-220 (non-isolated) 15 a d 2 pak 15 a to-220 (isolated) 0 1020304050 50 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawing 25 a to-220 (non-isolated) 25 a d 2 pak 25 a to-3 fastpak 35 a to-3 fastpak
triacs data sheets http://www.teccor.com e2 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e2.7 maximum allowable ambient temperature versus on-state current figure e2.8 on-state current versus on-state voltage (typical) (0.8 a and 1 a) figure e2.9 on-state current versus on-state voltage (typical) (4 a, 6 a, 8 a, and 10 a) figure e2.10 on-state current versus on-state voltage (typical) (15 a and 25 a) figure e2.11 normalized dc gate trigger current for all quadrants versus case temperature figure e2.12 normalized dc gate trigger voltage for all quadrants versus case temperature 120 100 80 60 40 25 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 to-220 devices and to-202 (type 1 and 3) rms on-state current [i t (rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c 1 a to-92 0.8 a to-92 current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? free air rating ? no heatsink to-202 (type 2 and 4) to-251 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 1 2 3 4 5 6 7 8 9 10 positive or negative instantaneous on-state voltage (v t ) ? volts positive or negative instantaneous on-state current (i t ) ? amps t c = 25 ?c 1 a 0.8 a 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 2 4 6 8 10 12 14 16 18 20 positive or negative instantaneous on-state voltage (v t ) ? volts positive or negative instantaneous on-state current (i t ) ? amps t c = 25 ?c 6-10 a 4a 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 10 20 30 40 50 60 70 80 90 positive or negative instantaneous on-state voltage (v t ) ? volts positive or negative instantaneous on-state current (i t ) ? amps t c = 25 ?c 15 a and 25 a 15 a and 25 a fastpak -65 -40 -15 +25 +65 +125 1.0 2.0 3.0 4.0 case temperature (t c ) ? ?c ratio of i gt i gt (t c = 25 ?c) -65 -15 -40 +25 +65 +125 0 .5 1.0 1.5 2.0 case temperature (t c ) ? ?c ratio of v gt v gt (t c = 25 ?c)
data sheets triacs ?2002 teccor electronics e2 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e2.13 peak surge current versus surge current duration figure e2.14 normalized dc holding current versus case temperature f igure e2.15 turn-on time versus gate trigger current (typical) supply frequency: 60 hz sinusoidal load: resistive rms on-state current [l t(rms) ]: maximum rated value at specified case temperature notes: 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. 25 a to -220 15 a 10 a 8 a 4 a 1 a 6 a 1 10 20 30 40 50 60 80 100 120 300 400 1000 1 10 100 1000 surge current duration ? full cycles peak surge (non-repetitive) on-state current (l tsm ) ? amps 200 0.8 a 25 a fastpak 35 a fastpak -65 -40 -15 +25 +65 +125 1.0 2.0 3.0 4.0 case temperature (t c ) ? ?c ratio of i h i h (t c = 25 ?c) initial on-state current = 200 ma dc 0.8 a - 10 a devices = 400 ma dc 15 a - 25 a devices 0 0 25 50 75 100 125 150 175 200 225 250 275 300 1 2 3 4 5 6 7 8 typical turn-on time (t gt ) ? sec dc gate trigger current (l gt ) ? ma devices with l gt = 10 ma devices with l gt = 25 ma devices with l gt = 50 ma t c = 25 ?c
triacs data sheets http://www.teccor.com e2 - 10 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e2.16 power dissipation (typical) versus on-state current (0.8 a and 1 a) figure e2.17 power dissipation (typical) versus on-state current (6 a to 10 a and 15 a) figure e2.18 power dissipation (typical) versus on-state current (25 a to 35 a) figure e2.19 power dissipation (typical) versus rms on-state current (4 a) rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts 0 0.25 0.50 0.75 1.0 1.25 0 0.5 1.0 1.5 current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 1 a 0.8 a 012345678910111213141516 0 2 4 6 8 10 12 14 16 18 rms on-state current [l t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts 6-10 a 15 a current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 0 8 16 24 32 40 0 5 10 15 20 25 30 35 40 45 rms on-state current [l t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 25 a 25 a - 35 a fastpaks rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts 0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 4 a 4.0
?2002 teccor electronics e3 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 u.l. recogn ized file #e71639 quadrac internally triggered triacs (4 a to 15 a) e3 general description te c c o r ? s quadrac devices are triacs that include a diac trigger mounted inside the same package. this device, developed by teccor, saves the user the expense and assembly time of buying a discrete diac and assembling in conjunction with a gated triac. also, the alternistor quadrac device (qxxxxlth) eliminates the need for a snubber network. the quadrac device is a bidirectional ac switch and is gate con- trolled for either polarity of main terminal voltage. its primary pur- pose is for ac switching and phase control applications such as speed controls, temperature modulation controls, and lighting controls where noise immunity is required. triac current capacities range from 4 a to 15 a with voltage ranges from 200 v to 600 v. quadrac devices are available in the to-220 package. the to-220 package is electrically isolated to 2500 v rms from the leads to mounting surface. 4000 v rms is available on special order. this means that no external isolation is required, thus eliminating the need for separate insulators and insulator-mount- ing steps and saving dollars over ?hot tab? devices. all teccor triac and diac chips have glass-passivated junctions to ensure long-term device reliability and parameter stability. variations of devices in this data sheet are available for custom design applications. consult the factory for more information. features ? glass-passivated junctions ? electrically-isolated package ? internal trigger diac ? high surge capability ? up to 200 a ? high voltage capability ? 200 v to 600 v to-220 isolated mt2 mt1 t e3
quadrac data sheets http://www.teccor.com e3 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog specific test conditions [? v] ? dynamic breakback voltage (forward and reverse) ? v bo ? breakover voltage symmetry c t ? trigger firing capacitance di/dt ? maximum rate-of-change of on-state current dv/dt ? critical rate-of-rise of off-state voltage at rated v drm gate open dv/dt(c) ? critical rate-of-rise of commutation voltage at rated v drm and i t(rms) commutating di/dt = 0.54 rated i t(rms) /ms; gate unenergized i 2 t ? rms surge (non-repetitive) on-st ate current for period of 8.3 ms for fusing i bo ? peak breakover current i drm ? peak off-state current gate open; v drm = maximum rated value i gtm ? peak gate trigger current (10 s max) i h ? holding current; gate open i t(rms) ? rms on-state current, conduction angle of 360 i tsm ? peak one-cycle surge t gt ? gate controlled turn-on time v bo ? breakover voltage (forward and reverse) v drm ? repetitive peak blocking voltage v tm ? peak on-state voltage at maximum rated rms current general notes ? all measurements are made at 60 hz with resistive load at an ambi- ent temperature of +25 c unless otherwise specified. ? operating temperature range (t j ) is -40 c to +125 c. ? storage temperature range (t s ) is -40 c to +125 c. ? lead solder temperature is a maximum of +230 c for 10 seconds maximum; 1/16" (1.59 mm) from case. ? the case temperature (t c ) is measured as shown on dimensional outline drawings. see ?package dimensions? section of this catalog. electrical specification notes (1) for either polarity of mt2 with reference to mt1 (2) see figure e3.1 for i h versus t c . (3) see figure e3.4 and figure e3.5 for i t versus v t . (4) see figure e3.9 for surge ra tings with specific durations. i t(rms) part no. v drm i drm v tm trigger diac specifications (t?mt1) isolated ? v bo v bo [ ? v ]i bo c t (5) to-220 (1) volts (1) (10) mamps (1) (3) volts (7) volts (6) volts (6) volts amps (11) farads t c = 25 c t c = 100 c t c = 125 c t c = 25 c see ?package dimensions? section for variations. (12) min max max max min max min max max 4a q2004lt 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4004lt 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6004lt 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 6a q2006lt 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4006lt 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6006lt 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4006lth 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6006lth 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 8a q2008lt 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4008lt 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6008lt 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4008lth 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6008lth 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 10 a q2010lt 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4010lt 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6010lt 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4010lth 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6010lth 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 15 a q2015lt 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4015lt 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6015lt 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q4015lth 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 q6015lth 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 mt1 mt2 t
data sheets quadrac ?2002 teccor electronics e3 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 (5) see figure e3.6, figure e3.7, and figure e3.8 for current rating at specific operating temperature. (6) see figure e3.2 and figure e3.3 for test circuit. (7) ? v bo = [+ v bo ] - [- v bo ] (8) see figure e3.7 and figure e3.8 for maximum allowable case temperature at maximum rated current. (9) trigger firing capacitance = 0.1 f with 0.1 s rise time (10) t c = t j for test conditions in off state (11) maximum required value to ensure sufficient gate current (12) see package outlines for lead fo rm configurations. when ordering special lead forming, add type number as suffix to part number. electrical isolation all teccor isolated quadrac packages withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab over the operating temperature range of the device. the following iso- lation table shows standard and optional isolation ratings. * ul recognized file #e71639 **for 4000 v isolation, use ?v? suffix in part number. i h i tsm dv/dt(c) dv/dt t gt i 2 t i gtm di/dt (1) (2) mamps (4) (8) amps (1) (5) (8) volts/sec (1) volts/sec (6) (9) sec amps 2 sec amps (9) amps/sec t c = 100 c t c = 125 c max 60/50hz min min typ 40 55/46 3 75 50 3 12.5 1.2 50 40 55/46 3 75 50 3 12.5 1.2 50 40 55/46 3 50 50 3 12.5 1.2 50 50 80/65 4 150 100 3 26.5 1.5 70 50 80/65 4 150 100 3 26.5 1.5 70 50 80/65 4 125 85 3 26.5 1.5 70 50 80/65 25 575 450 3 26.5 1.5 70 50 80/65 25 425 350 3 26.5 1.5 70 60 100/83 4 175 120 3 41 1.5 70 60 100/83 4 175 120 3 41 1.5 70 60 100/83 4 150 100 3 41 1.5 70 60 100/83 25 575 450 3 41 1.5 70 60 100/83 25 425 350 3 41 1.5 70 60 120/100 4 200 150 3 60 1.5 70 60 120/100 4 200 150 3 60 1.5 70 60 120/100 4 175 120 3 60 1.5 70 60 120/100 30 925 700 3 60 1.5 70 60 120/100 30 775 600 3 60 1.5 70 70 200/167 4 300 200 3 166 1.5 100 70 200/167 4 300 200 3 166 1.5 100 70 200/167 4 200 150 3 166 1.5 100 70 200/167 30 925 700 3 166 1.5 100 70 200/167 30 775 600 3 166 1.5 100 thermal resistance (steady state) r jc [r ja ] c/w (typ) type isolated to-220 4a 3.6 [50] 6a 3.3 8a 2.8 10 a 2.6 15 a 2.1 electrical isolation from leads to mounting tab * v ac rms type 2500 standard 4000 optional **
quadrac data sheets http://www.teccor.com e3 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e3.1 normalized dc holding current versus case temperature figure e3.2 test circuit figure e3.3 test circuit waveforms figure e3.4 on-state current versus on-state voltage (typical) (4 a to 10 a) figure e3.5 on-state current versus on-state voltage (typical) (15 a) figure e3.6 maximum allowable ambient temperature versus on-state current case temperature (t c ) ? ?c -40 -15 +25 +65 +105 i h i h (t c = 25 ?c) 2.0 1.5 1.0 .5 0 initial on-state current = 200 ma dc 4 a to 10 a = 400 ma dc 15 a ratio of +125 120 v 60 hz r l d.u.t. mt2 mt1 v c c t = 0.1 f t v c ? v+ -v bo ? v- +v bo 20 18 16 14 12 10 8 6 4 2 0 0 0.6 0.8 1.0 1.2 1.4 1.6 positive or negative instantaneous on-state current (i t ) ? amps positive or negative instantaneous on-state voltage (v t ) ? volts 6 a, 8 a, and 10 a 4 a t c = 25 ?c 90 80 70 60 50 40 30 20 10 0 0 0.6 0.8 1.0 1.2 1.4 1.6 positive or negative instantaneous on-state current (i t ) ? amps 15 a t c = 25?c 1.8 positive or negative instantaneous on-state voltage (v t ) ? volts 120 100 80 60 40 20 rms on-state current [i t(rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c 25 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 4 a
data sheets quadrac ?2002 teccor electronics e3 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e3.7 maximum allowable case temperature versus on-state current (4 a) figure e3.8 maximum allowable case temperature versus on-state current (6 a to 15 a) figure e3.9 peak surge current versus surge current duration figure e3.10 power dissipation (typical) versus on-state current (4 a) figure e3.11 power dissipation (typical) versus on-state current (6 a to 10 a and 15 a) figure e3.12 normalized diac v bo versus junction temperature rms on-state current [i t(rms) ] ? amps 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawings 130 120 110 100 90 80 70 60 0 4 a rms on-state current [i t(rms) ] ? amps 0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawings 130 120 110 100 90 80 70 60 0 6 a 10 a 8 a 15 a 200 120 40 1 2 3 4 5 6 8 10 20 3040 60 80 100 200 300 600 1000 80 60 50 100 8 6 5 10 30 20 4 1 3 2 surge current duration ? full cycles peak surge (non-repetitive) on-state current (i tsm ) ? amps supply frequency: 60 hz sinusoidal load: resistive rms on-state current [i t(rms) ]: maximum rated value at specified case temperature notes: 1) gates control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady state rated value. 15 a 10 a 8 a 6 a 4 a average on-state power dissipation [p d(av) ] ? watts rms on-state current [i t(rms) ] ? amps 4.0 3.0 2.0 1.0 0 0 1.0 2.0 3.0 4.0 5.0 current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 4 a current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? 18 16 14 12 10 8 6 4 2 0 16 14 12 10 8 6 4 2 0 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts 15 a 6 a to 10 a -8 -6 -4 -2 0 +2 +4 -40 -20 0 +20 +40 +60 +80 +100 +120 +140 junction temperature (t j ) ? ?c percentage of v bo change ? %
notes
?2002 teccor electronics e4 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 selected package s* u.l. recogn ized file #e71639 alternistor triacs (6 a to 40 a) e4 general description teccor offers bidirectional alternistors with current ratings from 6 a to 40 a and voltages from 200 v to 1000 v as part of teccor's broad line of thyristors. teccor's alternistor is specifically designed for applications that switch highly inductive loads. a special chip offers the same performance as two thyristors (scrs) wired inverse parallel (back-to-back), providing better turn-off behavior than a standard triac. an alternistor may be trig- gered from a blocking to conduction state for either polarity of applied ac voltage with operating modes in quadrants i, ii, and iii. this new chip construction provides two electrically separate scr structures, providing enhanced dv/dt characteristics while retaining the advantages of a single-chip device. all alternistors have glass-passivated junctions to ensure long- term reliability and parameter stability. teccor's glass-passivated junctions offer a reliable barrier against junction contamination. teccor's to-218x package is designed for heavy, steady power- handling capability. it features large eyelet terminals for ease of soldering heavy gauge hook-up wire. all the isolated packages have a standard isolation voltage rating of 2500 v rms . variations of devices covered in this data sheet are available for custom design applications. consult the factory for further information. features ? high surge current capability ? glass-passivated junctions ? 2500 v ac isolation for l, j, and k packages ? high commutating dv/dt ? high static dv/dt * to-220 * to-218 * to-218x mt2 mt1 g e4 to-263 d 2 pak to-252 d-pak to-251 v-pak
alternistor triacs data sheets http://www.teccor.com e4 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog see ?general notes? and ?electrical specification notes? on page e4 - 5. i t(rms) part number v drm i gt i drm isolated non-isolated (4)(16) t0-220 to-220 to-251 v-pak to-252 d-pak to-263 d 2 pak (1) volts (3) (7) (15) (17) mamps (1) (18) mamps qi qii qiii t c = 25 c t c = 100 c t c = 125 c max see ?package dimensions? section for variations. (11) min max max 6a q2006vh3 q2006dh3 200 10 10 10 0.01 0.5 2 q4006vh3 q4006dh3 400 10 10 10 0.01 0.5 2 q6006vh3 q6006dh3 600 10 10 10 0.01 0.5 2 q8006vh3 q8006dh3 800 10 10 10 0.01 0.5 2 qk006vh3 qk006dh3 1000 10 10 10 0.02 2 q2006vh4 q2006dh4 200 35 35 35 0.01 0.5 2 q4006vh4 q4006dh4 400 35 35 35 0.01 0.5 2 q6006vh4 q6006dh4 600 35 35 35 0.01 0.5 2 q8006vh4 q8006dh4 800 35 35 35 0.01 0.5 2 qk006vh4 qk006dh4 1000 35 35 35 0.02 2 q2006lh4 q2006rh4 q2006nh4 200 35 35 35 0.01 0.5 2 q4006lh4 q4006rh4 q4006nh4 400 35 35 35 0.01 0.5 2 q6006lh4 q6006rh4 q6006nh4 600 35 35 35 0.01 0.5 2 q8006lh4 q8006rh4 q8006nh4 800 35 35 35 0.01 0.5 2 qk006lh4 qk006rh4 qk006nh4 1000 35 35 35 0.02 3 8a q2008vh3 q2008dh3 200 10 10 10 0.01 0.5 2 q4008vh3 q4008dh3 400 10 10 10 0.01 0.5 2 q6008vh3 q6008dh3 600 10 10 10 0.01 0.5 2 q8008vh3 q8008dh3 800 10 10 10 0.01 0.5 2 qk008vh3 qk008dh3 1000 10 10 10 0.02 2 q2008vh4 q2008dh4 200 35 35 35 0.01 0.5 2 q4008vh4 q4008dh4 400 35 35 35 0.01 0.5 2 q6008vh4 q6008dh4 600 35 35 35 0.01 0.5 2 q8008vh4 q8008dh4 800 35 35 35 0.01 0.5 2 qk008vh4 qk008dh4 1000 35 35 35 0.02 2 q2008lh4 q2008rh4 q2008nh4 200 35 35 35 0.01 0.5 2 q4008lh4 q4008rh4 q4008nh4 400 35 35 35 0.01 0.5 2 q6008lh4 q6008rh4 q6008nh4 600 35 35 35 0.01 0.5 2 q8008lh4 q8008rh4 q8008nh4 800 35 35 35 0.01 0.5 2 qk008lh4 qk008rh4 qk008nh4 1000 35 35 35 0.02 3 10 a q2010lh5 q2010rh5 q2010nh5 200 50 50 50 0.01 0.5 2 q4010lh5 q4010rh5 q4010nh5 400 50 50 50 0.01 0.5 2 q6010lh5 q6010rh5 q6010nh5 600 50 50 50 0.01 0.5 2 q8010lh5 q8010rh5 q8010nh5 800 50 50 50 0.01 0.5 2 qk010lh5 qk010rh5 qk010nh5 1000 50 50 50 0.02 3 12 a q2012lh5 q2012rh5 q2012nh5 200 50 50 50 0.01 0.5 2 q4012lh5 q4012rh5 q4012nh5 400 50 50 50 0.01 0.5 2 q6012lh5 q6012rh5 q6012nh5 600 50 50 50 0.01 0.5 2 q8012lh5 q8012rh5 q8012nh5 800 50 50 50 0.01 0.5 2 qk012lh5 qk012rh5 qk012nh5 1000 50 50 50 0.02 3 mt1 mt2 g mt1 g mt2 mt2 mt2 mt2 g mt1 mt2 mt2 mt1 g mt2 mt2 mt1 g
data sheets alternistor triacs ?2002 teccor electronics e4 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 see ?general notes? and ?electrical specification notes? on page e4 - 5. v gt v tm i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (2) (6) (15) (17) (20) volts (1) (5) volts (1) (8) (12) mamps (14) amps (14) watts watts (9) (13) amps (1) (4) (13) volts/sec (1) volts/ sec (10) sec amps 2 sec (19) amps/sec t c = 25 c 60/50 hz t c = 100 c t c = 125 c max max max min min typ 1.3 1.6 15 1.6 18 0.4 65/55 20 100 75 4 17.5 70 1.3 1.6 15 1.6 18 0.4 65/55 20 100 75 4 17.5 70 1.3 1.6 15 1.6 18 0.4 65/55 20 75 50 4 17.5 70 1.3 1.6 15 1.6 18 0.4 65/55 20 50 40 4 17.5 70 1.3 1.6 15 1.6 18 0.4 65/55 20 40 4 17.5 70 1.3 1.6 35 1.6 18 0.5 65/55 25 500 400 4 17.5 70 1.3 1.6 35 1.6 18 0.5 65/55 25 500 400 4 17.5 70 1.3 1.6 35 1.6 18 0.5 65/55 25 400 300 4 17.5 70 1.3 1.6 35 1.6 18 0.5 65/55 25 300 200 4 17.5 70 1.3 1.6 35 1.6 18 0.5 65/55 25 150 4 17.5 70 1.3 1.6 35 1.6 18 0.5 85/80 25 750 600 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 575 450 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 425 350 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 300 250 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 150 4 30 70 1.3 1.6 15 1.6 18 0.4 85/80 20 100 75 4 30 70 1.3 1.6 15 1.6 18 0.4 85/80 20 100 75 4 30 70 1.3 1.6 15 1.6 18 0.4 85/80 20 75 50 4 30 70 1.3 1.6 15 1.6 18 0.4 85/80 20 50 40 4 30 70 1.3 1.6 15 1.6 18 0.4 85/80 20 40 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 750 400 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 575 450 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 425 350 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 300 250 4 30 70 1.3 1.6 35 1.6 18 0.5 85/80 25 150 4 30 70 1.3 1.6 35 2 20 0.5 100/83 25 500 400 4 41 70 1.3 1.6 35 2 20 0.5 100/83 25 500 400 4 41 70 1.3 1.6 35 2 20 0.5 100/83 25 400 300 4 41 70 1.3 1.6 35 2 20 0.5 100/83 25 300 200 4 41 70 1.3 1.6 35 2 20 0.5 100/83 25 150 4 41 70 1.3 1.6 50 2 20 0.5 120/110 30 1150 1000 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 1000 750 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 850 650 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 650 500 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 300 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 1150 1000 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 1000 750 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 850 650 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 650 500 4 60 70 1.3 1.6 50 2 20 0.5 120/110 30 300 4 60 70
alternistor triacs data sheets http://www.teccor.com e4 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog see ?general notes? and ?electrical specification notes? on page e4 - 5. test conditions di/dt ? maximum rate-of-change of on-state current dv/dt ? critical rate-of-rise of off-state voltage at rated v drm gate open dv/dt(c) ? critical rate-of-rise of commutation voltage at rated v drm and i t(rms) commutating di/dt = 0.54 rated i t(rms) /ms; gate unenergized i 2 t ? rms surge (non-repetitive) on-st ate current for period of 8.3 ms for fusing i drm ? peak off-state current gate open; v drm = maximum rated value i gt ? dc gate trigger current in specific operating quadrants; v d = 12 v dc i gtm ? peak gate trigger current i h ? holding current (dc); gate open i t(rms) ? rms on-state current conduction angle of 360 i tsm ? peak one-cycle surge p g(av) ? average gate power dissipation p gm ? peak gate power dissipation; i gt i gt m t gt ? gate controlled turn-on time; i gt = 300 ma with 0.1 s rise time v drm ? repetitive peak blocking voltage v gt ? dc gate trigger voltage; v d = 12 v dc v tm ? peak on-state voltage at maximum rated rms current i t(rms) part number v drm i gt isolated non-isolated (4)(16) t0-220 to-218 (16) to-218x to-220 to-263 d 2 pak (1) volts (3) (7) (15) (17) mamps qi qii qiii max see ?package dimensions? section for variations. (11) max 16 a q2016lh3 q2016rh3 q2016nh3 200 20 20 20 q4016lh3 q4016rh3 q4016nh3 400 20 20 20 q6016lh3 q6016rh3 q6016nh3 600 20 20 20 q8016lh3 q8016rh3 q8016nh3 800 20 20 20 qk016lh3 qk016rh3 qk016nh3 1000 20 20 20 q2016lh4 q2016rh4 q2016nh4 200 35 35 35 q4016lh4 q4016rh4 q4016nh4 400 35 35 35 q6016lh4 q6016rh4 q6016nh4 600 35 35 35 q8016lh4 q8016rh4 q8016nh4 800 35 35 35 qk016lh4 qk016rh4 qk016nh4 1000 35 35 35 q2016lh6 q2016rh6 q2016nh6 200 80 80 80 q4016lh6 q4016rh6 q4016nh6 400 80 80 80 q6016lh6 q6016rh6 q6016nh6 600 80 80 80 q8016lh6 q8016rh6 q8016nh6 800 80 80 80 qk016lh6 qk016rh6 qk016nh6 1000 80 80 80 25 a q2025l6 q2025k6 q2025j6 q2025r6 q2025nh6 200 80 80 80 q4025l6 q4025k6 q4025j6 q4025r6 q4025nh6 400 80 80 80 q6025l6 q6025k6 q6025j6 q6025r6 q6025nh6 600 80 80 80 q8025l6 q8025k6 q8025j6 q8025r6 q8025nh6 800 80 80 80 qk025l6 qk025k6 qk025r6 qk025nh6 1000 80 80 80 30 a q2030lh5 200 50 50 50 q4030lh5 400 50 50 50 q6030lh5 600 50 50 50 35 a q2035rh5 q2035nh5 200 50 50 50 q4035rh5 q4035nh5 400 50 50 50 q6035rh5 q6035nh5 600 50 50 50 40 a q2040k7 q2040j7 200 100 100 100 q4040k7 q4040j7 400 100 100 100 q6040k7 q6040j7 600 100 100 100 q8040k7 q8040j7 800 100 100 100 qk040k7 1000 100 100 100 mt1 mt2 g k g a k a g a a mt1 g mt2 mt2 mt2 mt2 mt1 g
data sheets alternistor triacs ?2002 teccor electronics e4 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 general notes ? all measurements are made at 60 hz with a resistive load at an ambient temperature of +25 c unless specified otherwise. ? operating temperature range (t j ) is -40 c to +125 c. ? storage temperature range (t s ) is -40 c to +125 c. ? lead solder temperature is a maximum of 230 c for 10 seconds maximum 1/16" (1.59 mm) from case. ? the case temperature (t c ) is measured as shown in the dimen- sional outline drawings. see ?package dimensions? section. electrical specification notes (1) for either polarity of mt2 with reference to mt1 terminal (2) for either polarity of gate voltage (v gt ) with reference to mt1 terminal (3) see gate characteristics and definition of quadrants. (4) see figure e4.1 through figure e4.4 for current rating at specific operating temperature and figure 4.16 for free air rating (no heat sink). (5) see figure e4.5 and figure e4.6 for i t and v t . (6) see figure e4.7 for v gt versus t c . (7) see figure e4.8 for i gt versus t c . (8) see figure e4.9 for i h versus t c . (9) see figure e4.10 and figure e4.11 for surge rating with specific durations. i drm v gt v tm i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (18) mamps (2) (6) (15) (17) (20) volts (1) (5) volts (1) (8) (12) mamps (14) amps (14) watts watts (9) (13) amps (1) (4) (13) volts/sec (1) volts/ sec (10) sec amps 2 sec (19) amps/sec t c = 25 c t c = 100 c t c = 125 c t c = 25 c t c = 25 c 60/50 hz t c = 100 c t c = 125 c max max max max min min typ 0.05 0.5 2 1.5 1.6 35 2 20 0.5 200/167 20 500 400 3 166 100 0.05 0.5 27 1.5 1.6 35 2 20 0.5 200/167 20 400 350 3 166 100 0.05 0.5 2 1.5 1.6 35 2 20 0.5 200/167 20 300 250 3 166 100 0.1 1 3 1.5 1.6 35 2 20 0.5 200/167 20 275 200 3 166 100 0.1 3 1.5 1.6 35 2 20 0.5 200/167 20 200 3 166 100 0.05 0.5 2 2 1.6 50 2 20 0.5 200/167 25 650 500 3 166 100 0.05 0.5 2 2 1.6 50 2 20 0.5 200/167 25 600 475 3 166 100 0.05 0.5 2 2 1.6 50 2 20 0.5 200/167 25 500 400 3 166 100 0.1 1 3 2 1.6 50 2 20 0.5 200/167 25 425 350 3 166 100 0.1 3 2 1.6 50 2 20 0.5 200/167 25 300 3 166 100 0.05 0.5 2 2.5 1.6 70 2 20 0.5 200/167 30 875 600 5 166 100 0.05 0.5 2 2.5 1.6 70 2 20 0.5 200/167 30 875 600 5 166 100 0.05 0.5 2 2.5 1.6 70 2 20 0.5 200/167 30 800 520 5 166 100 0.1 1 3 2.5 1.6 70 2 20 0.5 200/167 30 700 475 5 166 100 0.1 3 2.5 1.6 70 2 20 0.5 200/167 30 350 5 166 100 0.05 0.5 2 2.5 1.8 100 2 20 0.5 250/208 30 875 600 5 259 100 0.05 0.5 2 2.5 1.8 100 2 20 0.5 250/208 30 875 600 5 259 100 0.05 0.5 2 2.5 1.8 100 2 20 0.5 250/208 30 800 520 5 259 100 0.1 1 3 2.5 1.8 100 2 20 0.5 250/208 30 700 475 5 259 100 0.1 3 2.5 1.8 100 2 20 0.5 250/208 30 400 5 259 100 0.05 0.5 2 2 1.4 75 2 20 0.5 350/290 20 650 500 3 508 100 0.05 0.5 2 2 1.4 75 2 20 0.5 350/290 20 600 475 3 508 100 0.05 0.5 2 2 1.4 75 2 20 0.5 350/290 20 500 400 3 508 100 0.05 0.5 2 2 1.5 75 2 20 0.5 350/290 20 650 500 3 508 100 0.05 0.5 2 2 1.5 75 2 20 0.5 350/290 20 600 475 3 508 100 0.05 0.5 2 2 1.5 75 2 20 0.5 350/290 20 500 400 3 508 100 0.2 2 5 2.5 1.8 120 4 40 0.8 400/335 50 1100 700 5 664 150 0.2 2 5 2.5 1.8 120 4 40 0.8 400/335 50 1100 700 5 664 150 0.2 2 5 2.5 1.8 120 4 40 0.8 400/335 50 1000 625 5 664 150 0.2 2 5 2.5 1.8 120 4 40 0.8 400/335 50 900 575 5 664 150 0.2 5 2.5 1.8 120 4 40 0.8 400/335 50 500 5 664 150
alternistor triacs data sheets http://www.teccor.com e4 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog (10) see figure e4.12 for t gt versus i gt . (11) see package outlines for lead fo rm configurations. when ordering special lead forming, add type number as suffix to part number. (12) initial on-state current = 400 ma dc for 16 a to 40 a devices and 100 ma for 6 a to 12 a devices. (13) see figure e4.1 through figure e4.4 for maximum allowable case temperature at maximum rated current. (14) pulse width 10 s; i gt i gtm (15) for 6 a to 12 a devices, r l = 60 ? ; 16 a and above, r l = 30 ? (16) 40 a pin terminal leads on k package can run 100 c to 125 c. (17) alternistor does not turn on in quadrant iv. (18) t c = t j for test conditions in off state (19) i gt = 200 ma for 6 a to 12 a devices and 500 ma for 16 a to 40 a devices with gate pulse having rise time of 0.1 s. (20) minimum non-trigger v gt at 125 c is 0.2 v. gate characteristics teccor triacs may be turned on in the following ways: ? in-phase signals (with standard ac line) using quadrants i and iii ? application of unipolar pulses (gate always negative), using quadrants ii and iii with negative gate pulses in all cases, if maximum surge capability is required, gate pulses should be a minimum of one magnitude above minimum i gt rating with a steep rising waveform ( 1 s rise time). if qiv and qi operation is required (gate always positive), see figure an1002.8, ?amplified gate? thyristor circuit. definition of quadrants electrical isolation teccor?s isolated alternistor packages withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab, over the operating temperature range of the device. the following iso- lation table shows standard and optional isolation ratings. * ul recognized file e71639 ** for 4000 v isolation, use v suffix in part number. * ul recognized product per ul file e71639 ** for 4000 v isolation, use v suffix in part number. electrical isolation from leads to mounting tab * vacrms to-218 isolated to-220 isolated to-218x isolated 2500 standard standard standard 4000 n/a optional ** n/a mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - note: alternistors will not operate in qiv thermal resistance (steady state) r jc [r ja ] (typ. ) c/w package code kjlrdvn type to-218 isolated * to-218x isolated * to-220 isolated ** to-220 non-isolated to-252 d-pak to-251 v-pak to-263 d 2 pak 6 a 3.3 [50] 1.80 [45] 2.1 2.3 [64] 1.80 8 a 2.8 1.50 1.8 2.1 1.50 10 a 2.6 1.30 1.30 12 a 2.3 1.20 1.20 16 a 2.1 1.10 1.10 25 a 1.35 1.32 2.0 0.87 0.87 30 a 2.3 35 a 0.85 40 a 0.97 0.95
data sheets alternistor triacs ?2002 teccor electronics e4 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e4.1 maximum allowable case temperature versus on-state current (6 a to 12 a) figure e4.2 maximum allowable case temperature versus on-state current (8 a to 12 a) figure e4.3 maximum allowable case temperature versus on-state current (16 a) figure e4.4 maximum allowable case temperature versus on-state current (25 a to 40 a) figure e4.5 on-state current versus on-state voltage (typical) (6 a to 12 a) figure e4.6 on-state current versus on-state voltage (typical) (16 a to 40 a) 02468101214 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] - amps maximum allowable case temperature (t c ) - ? c 12a to-220 (isolated) 10a to-220 (non-isolated) and d 2 pak 6a to-220 (isolated) 6a to-220 (non-isolated) and d 2 pak current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 02468101214 0 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 12 a to-220 (non-isolated) and to-263 10 a to-220 (isolated) 8 a to-220 (non-isolated), to-263, to-251, and to-252 current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawing 8 a to-220 (isolated) 0 60 70 80 90 100 110 120 130 0 5 10 15 rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ? c 16a to-220 (non-isolated) and to-263 16a to -220 (isolated) current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? case temperature: measured as shown on dimensional drawing 0 1020304050 50 60 70 80 90 100 110 120 130 rms on-state current [l t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 35 a to-220 (non-isolated) and to-263 25 a and 30 a to-220 (isolated) current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawing 40 a to- 218 (isolate d) 25 25 a to-220 (non-isolated) to-218 (isolated) to-263 0 2 6 8 10 12 14 16 18 20 0 0.6 0.8 1.0 1.2 1.4 1.6 positive or negative instantaneous on-state voltage (v t ) ? volts positive or negative instantaneous on-state current (i t ) ? amps t c = 25 ?c 4 6 a to 12 a devices 90 80 70 60 50 40 30 20 10 0 0 0.6 0.8 1.0 1.2 1.4 1.6 positive or negative instantaneous on-state current (i t ) ? amps t c = 25?c 1.8 positive or negative instantaneous on-state voltage (v t ) ? volts 40 a devices 16 a devices 25 a to 35 a devices
alternistor triacs data sheets http://www.teccor.com e4 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e4.7 normalized dc gate trigger voltage for all quadrants versus case temperature figure e4.8 normalized dc gate trigger current for all quadrants versus case temperature figure e4.9 normalized dc holding current versus case temperature figure e4.10 peak surge current versus surge current duration (6 a to 12 a) figure e4.11 peak surge current versus surge current duration (16 a to 40 a) figure e4.12 turn-on time versus gate trigger current (typical) 0 .5 1.0 1.5 2.0 -65 -15 +65 +25 +125 -40 case temperature (t c ) ? ?c v gt (t c = 25 ?c) ratio of v gt 0 1.0 2.0 3.0 4.0 -65 -15 +65 +25 +125 -40 case temperature (t c ) ? ?c i gt (t c = 25 ?c) ratio of i gt 0 1.0 2.0 3.0 4.0 -65 -15 +65 +25 +125 -40 case temperature (t c ) ? ?c i h (t c = 25 ?c) ratio of i h initial on-state current = 400 ma dc 16 a to 40 a devices = 100 ma dc 6 to 12a devices 200 120 40 1 2 3 45 6 8 10 20 30 40 60 80 100 200 300 600 1000 80 60 50 100 8 6 5 10 30 20 4 1 3 2 surge current duration ? full cycles peak surge (non-repetitive) on-state current (i tsm ) ? amps supply frequency: 60 hz sinusoidal load: resistive rms on-state current [i t(rms) ]: maximum rated value at specified case temperature notes: 1) gate control may be lost during and immediately following surge current interval 2) overload may not be repeated until junction temperature has returned to steady state rated value. 10 a to 1 2 a devices 8 a to-251 and to- 252 8 a devices 6 a devices 6 a to -251 and to- 252 110 100 1000 10 20 30 40 50 60 80 100 250 300 400 1000 surge current duration ? full cycles peak surge (non-repetitive) on-state current (i tsm ) ? amps 200 notes: 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. supply frequency: 60hz sinusoidal load: resistive rms on-state current [i t(rms) ]: maximum rated value at specified case temperature 40 a de vices 35 a de vices 30 a de vice s 25 a de vice s 16 a de vices 0 100 200 300 400 500 0 2 4 6 8 10 dc gate trigger current ( i gt ) ? ma i gt = 80 to 100 ma typical turn-on time (t gt ) ? s i gt = 10 ma to 35 ma i gt = 50 ma
data sheets alternistor triacs ?2002 teccor electronics e4 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e4.13 power dissipation (typical) versus on-state current (6 a to 12 a) figure e4.14 power dissipation (typical) versus on-state current (16 a) figure e4.15 power dissipation (typical) versus on-state current (25 a to 40 a) figure e4.16 maximum allowable ambient temperature versus on-state current 01234567891011121314151 6 0 2 4 6 8 10 12 14 16 18 rms on-state curren t [l t(rms) ] ? ampss average on-state power dissipation [p d(av) ] ? watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? 6a to 12a devices 0246 8 10 12 14 16 0 2 4 6 8 10 12 14 16 18 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d (av) ] ? watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 16a devices 012 20 28 36 4 16 24 32 40 8 0 5 10 15 20 25 30 35 40 45 rms on-state current [i t(rms) ]?amps average on-state power dissipation [p d(av) ]?watts 25 a 40 a current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 30 a and 35 a devices 120 100 80 60 40 25 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2. 0 to-220 devices rms on-state current [i t (rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? free air rating ? no heatsink to-251 devices
notes
?2002 teccor electronics e5 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 selected package s* u.l. recogn ized file #e71639 sensitive scrs (0.8 a to 10 a) e5 general description the teccor line of sensitive scr semiconductors are half-wave unidirectional, gate-controlled rectifiers (scr-thyristor) which complement teccor's line of power scrs. this group of packages offers ratings of 0.8 a to 10 a, and 200 v to 600 v with gate sensitivities of 12 a to 500 a. for gate currents in the 10 ma to 50 ma ranges, see ?scrs? section of this catalog. the to-220 and to-92 are electrically isolated where the case or tab is internally isolated to allow the use of low-cost assembly and convenient packaging techniques. teccor's line of scrs features glass-passivated junctions to ensure long-term device reliability and parameter stability. teccor's glass offers a rugged, reliable barrier against junction contamination. tape-and-reel packaging is available for the to-92 package. consult the factory for more information. variations of devices covered in this data sheet are available for custom design applications. consult the factory for more information. features ? electrically-isolated to-220 package ? high voltage capability ? up to 600 v ? high surge capability ? up to 100 a ? glass-passivated chip compak features ? surface mount package ? 0.8 a series ? new small-profile three-leaded compak package ? four gate sensitivities available ? packaged in embossed carrier tape with 2,500 devices per reel ? can replace sot-223 e5 to-202 to-92 3-lead compak * to-220 isolated to-252 d-pak to-251 v-pak ak g
sensitive scrs data sheets http://www.teccor.com e5 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog see ?general notes? on page e5 - 4 and ?electrical specifications notes? on page e5 - 5 type part number i t v drm & v rrm i gt i drm & i rrm v tm non-isolated to-92 to-202 to-251 v-pak compak to-252 d-pak (1) amps volts (2) (12) (14) (18) amps (20) (21) amps (3) (10) volts see ?package dimensions? section for variations. (11) i t(rms) i t(av) t c or t l = 25 c t c or t l = 100 c t c or t l = 110 c max min max max max 0.8 a s2s1 0.8 0.51 200 12 2 100 1.7 s4s1 0.8 0.51 400 12 2 100 1.7 s6s1 0.8 0.51 600 12 2 100 1.7 s2s2 0.8 0.51 200 50 2 100 1.7 s4s2 0.8 0.51 400 50 2 100 1.7 s6s2 0.8 0.51 600 50 2 100 1.7 s2s 0.8 0.51 200 200 2 100 1.7 s4s 0.8 0.51 400 200 2 100 1.7 s6s 0.8 0.51 600 200 2 100 1.7 s2s3 0.8 0.51 200 500 2 100 1.7 s4s3 0.8 0.51 400 500 2 100 1.7 s6s3 0.8 0.51 600 500 2 100 1.7 ec103b 0.8 0.51 200 200 1 50 1.7 ec103d 0.8 0.51 400 200 1 50 1.7 ec103m 0.8 0.51 600 200 2 100 1.7 ec103b1 0.8 0.51 200 12 1 50 1.7 ec103d1 0.8 0.51 400 12 1 50 1.7 ec103m1 0.8 0.51 600 12 2 100 1.7 ec103b2 0.8 0.51 200 50 1 50 1.7 ec103d2 0.8 0.51 400 50 1 50 1.7 ec103m2 0.8 0.51 600 50 2 100 1.7 ec103b3 0.8 0.51 200 500 1 50 1.7 ec103d3 0.8 0.51 400 500 1 50 1.7 ec103m3 0.8 0.51 600 500 2 100 1.7 2n5064 0.8 0.51 200 200 1 50 1.7 2n6565 0.8 0.51 400 200 1 100 1.7 1.5 a tcr22-4 1.5 0.95 200 200 1 100 1.5 tcr22-6 1.5 0.95 400 200 1 100 1.5 tcr22-8 1.5 0.95 600 200 2 100 1.5 4a t106b1 4 2.5 200 200 2 100 2.2 t106d1 4 2.5 400 200 2 100 2.2 t106m1 4 2.5 600 200 2 100 2.2 t107b1 4 2.5 200 500 2 100 2.5 t107d1 4 2.5 400 500 2 100 2.5 t107m1 4 2.5 600 500 2 100 2.5 s2004vs1 s2004ds1 4 2.5 200 50 2 100 1.6 s4004vs1 s4004ds1 4 2.5 400 50 2 100 1.6 s6004vs1 s6004ds1 4 2.5 600 50 2 100 1.6 s2004vs2 s2004ds2 4 2.5 200 200 2 100 1.6 s4004vs2 s4004ds2 4 2.5 400 200 2 100 1.6 s6004vs2 s6004ds2 4 2.5 600 200 2 100 1.6 k g a k a g a a a g k a g k a a k g
data sheets sensitive scrs ?2002 teccor electronics e5 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 . see ?general notes? on page e5 - 4 and ?electrical specifications notes? on page e5 - 5 v gt i h i gm v grm p gm p g(av) i tsm dv/dt di/dt t gt t q l 2 t (4) (12) (22) volts (5) (15) (16) (19) mamps (17) amps volts (17) watts watts (6) (7) (13) amps volts/sec amps/sec (8) sec (9) sec amps 2 /sec t c or t l = -40 c t c or t l = 25 c t c or t l = 110 c 60/50 hz max max min min typ (23) typ max 1.2 0.8 0.2 5 1 5 1 0.1 20/16 20 50 2 60 1.6 1.2 0.8 0.2 5 1 5 1 0.1 20/16 20 50 2 60 1.6 1.2 0.8 0.2 5 1 5 1 0.1 20/16 10 50 2 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 25 50 3 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 25 50 3 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 10 50 3 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 30 50 4 50 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 30 50 4 50 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 15 50 4 50 1.6 1.2 0.8 0.25 8 1 5 1 0.1 20/16 40 50 5 45 1.6 1.2 0.8 0.25 8 1 5 1 0.1 20/16 40 50 5 45 1.6 1.2 0.8 0.25 8 1 5 1 0.1 20/16 20 50 5 45 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 30 50 3.5 50 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 30 50 3.5 50 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 15 50 3.5 50 1.6 1.2 0.8 0.2 5 1 5 1 0.1 20/16 20 50 2 60 1.6 1.2 0.8 0.2 5 1 5 1 0.1 20/16 20 50 2 60 1.6 1.2 0.8 0.2 5 1 5 1 0.1 20/16 10 50 2 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 25 50 3 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 25 50 3 60 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 10 50 3 60 1.6 1.2 0.8 0.25 8 1 5 1 0.1 20/16 40 50 5 45 1.6 1.2 0.8 0.25 8 1 5 1 0.1 20/16 40 50 5 45 1.6 1.2 0.8 0.25 8 1 5 1 0.1 20/16 20 50 5 45 1.6 1.2 0.8 0.25 5 1 5 1 0.1 20/16 25 50 2.2 60 1.6 1.2 0.8 0.25 5 1 6 1 0.1 20/16 25 50 2.2 60 1.6 1 0.80.2551610.120/1660 50 3.550 1.6 1 0.80.2551610.120/1640 50 3.550 1.6 1 0.80.2551610.120/1630 50 3.550 1.6 1 0.8 0.2 5 1 6 1 0.1 20/16 8 50 4 50 1.6 1 0.8 0.2 5 1 6 1 0.1 20/16 8 50 4 50 1.6 1 0.8 0.2 5 1 6 1 0.1 20/16 8 50 4 50 1.6 1 0.8 0.2 6 1 6 1 0.1 20/16 8 50 5 45 1.6 1 0.8 0.2 6 1 6 1 0.1 20/16 8 50 5 45 1.6 1 0.8 0.2 6 1 6 1 0.1 20/16 8 50 5 45 1.6 1 0.8 0.2 4 1 6 1 0.1 30/25 8 50 3 50 3.7 1 0.8 0.2 4 1 6 1 0.1 30/25 8 50 3 50 3.7 1 0.8 0.2 4 1 6 1 0.1 30/25 8 50 3 50 3.7 1 0.8 0.2 6 1 6 1 0.1 30/25 8 50 4 50 3.7 1 0.8 0.2 6 1 6 1 0.1 30/25 8 50 4 50 3.7 1 0.8 0.2 6 1 6 1 0.1 30/25 8 50 4 50 3.7
sensitive scrs data sheets http://www.teccor.com e5 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog specific test conditions di/dt ? maximum rate-of-change of on-state current; i gt = 50 ma pulse width 15 sec with 0.1 s rise time dv/dt ? critical rate-of-rise of forward off-state voltage i 2 t ? rms surge (non-repetitive) on-state current for period of 8.3 ms for fusing i drm and i rrm ? peak off-state current at v drm and v rrm i gt ? dc gate trigger current v d = 6 v dc; r l = 100 ? i gm ? peak gate current i h ? dc holding current; initial on-state current = 20 ma i t ? maximum on-state current i tsm ? peak one-cycle forward surge current p g(av) ? average gate power dissipation p gm ? peak gate power dissipation t gt ? gate controlled turn-on time gate pulse = 10 ma; minimum width = 15 s with rise time 0.1 s t q ? circuit commutated turn-off time v drm and v rrm ? repetitive peak off-state forward and reverse voltage v grm ? peak reverse gate voltage v gt ? dc gate trigger voltage; v d = 6 v dc; r l = 100 ? v tm ? peak on-state voltage general notes ? teccor 2n5064 and 2n6565 series devices conform to all jedec registered data. see specificat ions table on pages e5 - 2 and e5 - 3. ? the case lead temperature ( t c or t l ) is measured as shown on dimensional outline drawings in the ?package dimensions? section of this catalog. ? all measurements (except i gt ) are made with an external resistor r gk = 1 k ? unless otherwise noted. ? all measurements are made at 60 hz with a resistive load at an ambient temperature of +25 c unless otherwise specified. ? operating temperature (t j ) is -65 c to +110 c for ec series devices, -65 c to +125 c for 2n series devices, -40 c to +125 c for ?tcr? series, and -40 c to +110 c for all others. ? storage temperature range (t s ) is -65 c to +150 c for to-92 devices, -40 c to +150 c for to-202 and compak devices, and -40 c to +125 c for all others. ? lead solder temperature is a maximum of +230 c for 10 seconds maximum 1/16" (1.59 mm) from case. type part number i t v drm & v rrm i gt i drm & i rrm v tm isolated non-isolated to-220 to-202 to-251 v-pak to-252 d-pak (1) amps volts (2) (12) amps (20) (21) amps (3) (10) volts see ?package dimensions? section for variations. (11) i t(rms) i t(av) t c = 25 c t c = 110 c max max min max max max max 6a s2006ls2 s2006fs21 s2006vs2 s2006ds2 6 3.8 200 200 5 250 1.6 s4006ls2 s4006fs21 s4006vs2 s4006ds2 6 3.8 400 200 5 250 1.6 s6006ls2 s6006fs21 s6006vs2 s6006ds2 6 3.8 600 200 5 250 1.6 s2006ls3 s2006fs31 s2006vs3 s2006ds3 6 3.8 200 500 5 250 1.6 s4006ls3 s4006fs31 s4006vs3 s4006ds3 6 3.8 400 500 5 250 1.6 s6006ls3 s6006fs31 s6006vs3 s6006ds3 6 3.8 600 500 5 250 1.6 8a s2008ls2 s2008fs21 s2008vs2 s2008ds2 8 5.1 200 200 5 250 1.6 s4008ls2 s4008fs21 s4008vs2 s4008ds2 8 5.1 400 200 5 250 1.6 s6008ls2 s6008fs21 s6008vs2 s6008ds2 8 5.1 600 200 5 250 1.6 s2008ls3 s2008fs31 s2008vs3 s2008ds3 8 5.1 200 500 5 250 1.6 s4008ls3 s4008fs31 s4008vs3 s4008ds3 8 5.1 400 500 5 250 1.6 s6008ls3 s6008fs31 s6008vs3 s6008ds3 8 5.1 600 500 5 250 1.6 10 a s2010ls2 s2010fs21 s2010vs2 s2010ds2 10 6.4 200 200 5 250 1.6 s4010ls2 s4010fs21 s4010vs2 s4010ds2 10 6.4 400 200 5 250 1.6 s6010ls2 s6010fs21 s6010vs2 s6010ds2 10 6.4 600 200 5 250 1.6 s2010ls3 s2010fs31 s2010vs3 s2010ds3 10 6.4 200 500 5 250 1.6 s4010ls3 s4010fs31 s4010vs3 s4010ds3 10 6.4 400 500 5 250 1.6 s6010ls3 s6010fs31 s6010vs3 s6010ds3 10 6.4 600 500 5 250 1.6 k a g k a g a a a g k a a k g
data sheets sensitive scrs ?2002 teccor electronics e5 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 electrical specifications notes (1) see figure e5.1 through figure e5.9 for current ratings at specified operating temperatures. (2) see figure e5.10 for i gt versus t c or t l . (3) see figure e5.11 for instantaneous on-state current (i t ) versus on- state voltage (v t ) typ. (4) see figure e5.12 for v gt versus t c or t l . (5) see figure e5.13 for i h versus t c or t l . (6) for more than one full cycle, see figure e5.14. (7) 0.8 a to 4 a devices also hav e a pulse peak forward current on- state rating (repetitive) of 75 a. this rating applies for operation at 60 hz, 75 c maximum tab (or anode) lead temperature, switching from 80 v peak, sinusoidal current pulse width of 10 s minimum, 15 s maximum. see figure e5.20 and figure e5.21. (8) see figure e5.15 for t gt versus i gt . (9) test conditions as follows: ? t c or t l 80 c, rectangular current waveform ? rate-of-rise of current 10 a/s ? rate-of-reversal of current 5a/s ? i tm = 1 a (50 s pulse), repetition rate = 60 pps ? v rrm = rated ? v r = 15 v minimum, v drm = rated ? rate-of-rise reapplied forward blocking voltage = 5 v/s ? gate bias = 0 v, 100 ? (during turn-off time interval) (10) test condition is maximum rated rms current except to-92 devices are 1.2 a pk ; t106/t107 devices are 4 a pk . (11) see package outlines for lead form configurations. when ordering special lead forming, add type number as suffix to part number. (12) v d = 6 v dc, r l = 100 ? (see figure e5.19 for simple test circuit for measuring gate trigger voltage and gate trigger current.) (13) see figure e5.1 through figure e5.9 for maximum allowable case temperature at maximum rated current. (14) i gt = 500 a maximum at t c = -40 c for t106 devices (15) i h = 10 ma maximum at t c = -65 c for 2n5064 series and 2n6565 series devices (16) i h = 6 ma maximum at t c = -40 c for t106 devices (17) pulse width 10 s (18) i gt = 350 a maximum at t c = -65 c for 2n5064 series and 2n6565 series devices (19) latching current can be higher than 20 ma for higher i gt types. also, latching current can be much higher at -40 c. see figure e5.18. (20) t c or t l = t j for test conditions in off state (21) i drm and i rrm = 50 a for 2n5064 and 100 a for 2n6565 at 125 c (22) to-92 devices specified at -65 c instead of -40 c (23) t c = 110 c v gt i h i gm v grm p gm p g(av) i tsm dv/dt di/dt t gt t q l 2 t (4) (12) (22) volts (5) (19) mamps (17) amps volts (17) watts watts (6) (13) amps volts/sec amps/sec (8) sec (9) sec amps 2 sec t c = -40 c t c = 25 c t c = 110 c t c = 110 c max max min 60/50 hz typ typ max 1 0.8 0.25 6 1 6 1 0.1 100/83 10 100 4 50 41 1 0.8 0.25 6 1 6 1 0.1 100/83 8 100 4 50 41 1 0.8 0.25 6 1 6 1 0.1 100/83 8 100 4 50 41 1 0.8 0.25 8 1 6 1 0.1 100/83 10 100 5 45 41 1 0.8 0.25 8 1 6 1 0.1 100/83 8 100 5 45 41 1 0.8 0.25 8 1 6 1 0.1 100/83 8 100 5 45 41 10.80.2561610.1100/8310 100 45041 10.80.2561610.1100/838 100 45041 10.80.2561610.1100/838 100 45041 10.80.2581610.1100/8310 100 54541 10.80.2581610.1100/838 100 54541 10.80.2581610.1100/838 100 54541 1 0.8 0.25 6 1 6 1 0.1 100/83 10 100 4 50 41 1 0.8 0.25 6 1 6 1 0.1 100/83 8 100 4 50 41 1 0.8 0.25 6 1 6 1 0.1 100/83 8 100 4 50 41 1 0.8 0.25 8 1 6 1 0.1 100/83 10 100 5 45 41 1 0.8 0.25 8 1 6 1 0.1 100/83 8 100 5 45 41 1 0.8 0.25 8 1 6 1 0.1 100/83 8 100 5 45 41
sensitive scrs data sheets http://www.teccor.com e5 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog *mounted on 1 cm 2 copper foil surface; two-ounce copper foil electrical isolation teccor?s isolated sensitive scrs will withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab over the device's operating temperature range. the following table shows other standard and optional isolation ratings. *ul recognized file #e71639 **for 4000 v isolation, use ?v? suffix in part number. figure e5.1 maximum allowable case temperature versus rms on-state current figure e5.2 maximum allowable case temperature versus rms on-state current figure e5.3 maximum allowable case temperature versus average on-state current thermal resistance (steady state) r jc [r ja ] c/w (typical) package code elf2fcdv type to-92 to-220 to-202 type 2, 4, & 41 to-202 type 1 & 3 compak to-252 d-pak to-251 v-pak 0.8 a 75 [160] 60* 1.5 a 50 [160] 4.0 a 10 [100] 6.2 [80] 3.0 3.8 [85] 6.0 a 4.0 [65] 4.3 1.8 2.4 8.0 a 3.4 3.9 1.5 2.1 10.0 a 3.0 3.4 1.45 1.72 electrical isolation * from leads to mounting tab v ac rms to-220 2500 standard 4000 optional ** 50 60 70 80 90 100 110 120 130 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? case temperature: measured as shown on dimensional drawing rms on-state current [ i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c compak 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 ec series jedec 2n series 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 40 50 60 70 80 90 100 110 120 130 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measured as shown on dimensional drawing rms on-state current [ i t(rms) ] ? amps maximum allowable case temperature ( t c ) ? ?c 2.6 4 a to-251 and to-252 t106 and t107 type 1 and 3 t106 and t107 type 2 and 4 tcr22 devices 0 0.1 0.2 0.3 0.4 0.5 0.6 50 60 70 80 90 100 110 120 130 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measured as shown on dimensional drawing average on-state current [ i t(av) ] ? amps maximum allowable case temperature ( t c ) ? ?c 0.51 compak ec series jedec 2n series
data sheets sensitive scrs ?2002 teccor electronics e5 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e5.4 maximum allowable case temperature versus average on-state current figure e5.5 maximum allowable ambient temperature versus on-state current figure e5.6 maximum allowable ambient temperature versus rms on-state current figure e5.7 maximum allowable ambient temperature versus average on-state current figure e5.8 maximum allowable case temperature versus rms on-state current figure e5.9 maximum allowable case temperature versus average on-state current 0 0.5 1.0 1.5 2.0 2.5 3.0 50 60 70 80 90 100 110 120 130 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c 0.95 40 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? case temperature: measured as shown on dimensional drawing 1.65 1.9 2.54 t106 and t107 type 1 and 3 t106 and t107 type 2 and 4 tcr22 devices 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 140 120 100 80 60 40 20 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? free air rating 1.5 a and jedec 2n series i t(av) and ec series i t(av) on-state current ? amps maximum allowable ambient temperature (t a ) ? ?c 1.5 a devices and jedec 2n series i t(rms) ec series i t(rms) 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 140 120 100 80 60 40 20 rms on-state current [i t(rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c 2.0 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? free air rating to-220 t106/t107 to-202 type 1 and 3 t106/t107 to-202 type 2 and 4 and to-251 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 20 40 60 80 100 120 140 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? free air rating average on-state current [i t(av) ] ? amps maximum allowable ambient temperature (t a ) ? ?c to-220 t106/t107 to-202 type 1 and 3 t106/t107 to-202 type 2 and 4 and to-251 80 246810 0 85 90 95 100 105 110 115 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? temperature: measured as shown on dimensional drawings rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 6 a to-220 and to-202 8 a to-220 and to-202 10 a to-220 and to-202 6 a to-251 and to-252 8 a to-251 and to-252 10 a to-251 and to-252 80 13456 0 85 90 95 100 105 110 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c 7 2 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? case temperature: measured as shown on dimensional drawings 6 a to-220 and to-202 8 a to-220 and to-202 10 a to-220 and to-202 6 a to-251 and to-252 8 a to-251 and to-252 10 a to-251 and to-252
sensitive scrs data sheets http://www.teccor.com e5 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e5.10 normalized dc gate-trigger current versus case temperature figure e5.11 instantaneous on-state current versus on-state voltage (typical) figure e5.12 normalized dc gate-trigger voltage versus case temperature figure e5.13 normalized dc holding current versus case temperature -65 -15 +25 +65 +110 +125 -40 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 case temperature (t c ) ? ?c ratio of i gt i gt (t c = 25 ?c) see general notes for specific device operating temperature range. 0 .6 .8 1.0 1.2 1.4 1.6 0 4 8 12 16 20 24 28 32 t c = 25?c 6 a to 10 a devices 0.8 a to 1.5 a to-92, t106/t107, and compak instantaneous on-state voltage (v t ) ? volts instantaneous on-state current (i t ) ? amps 4 a to-251 and to-252 -65 -15 +25 +65 +110 +125 -40 0 0.5 1.0 1.5 2.0 case temperature (t c ) ? ? c ratio of v gt v gt ( t c = 25 ? c) see general notes for specific operating temperature range -65 -40 -15 +25 +65 +110 +125 0 1.0 2.0 3.0 4.0 see general notes for specific operating temperature range. case temperature (t c ) ? ?c ratio of i h i h (t c = 25 ?c)
data sheets sensitive scrs ?2002 teccor electronics e5 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e5.14 peak surge on-state current versus surge current duration figure e5.15 typical turn-on time versus gate trigger current figure e5.16 power dissipation (typical) versus rms on-state current 1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 200 300 400 600 100 0 1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 200 supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: max rated value at specified case temperature sur g e current duration ? full cycles peak surge (non-repetitive) on-state current (i tsm ) ? amps notes: 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. 6 a devices 8 a devices 10 a devices 4 a to-251 and to-252 1.5 a devices to-106 and to-107 0.8 a to-92 and compak 0.01 0.1 1 10 100 0.1 1.0 10 100 i gt = 50 a max i gt = 200 a max i gt = 500 a max t c = 25 ?c i gt = 12 a max dc gate trigger current (i gt ) ? ma turn-on time (t gt ) ? s 01234 1.0 2.0 3.0 4.0 5.0 t106 and t107 0.8 a to-92 and compak 1.5 a devices rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: half sine wave load: resistive or inductive conduction angle: 180? 4 a to-251 and to-252
sensitive scrs data sheets http://www.teccor.com e5 - 10 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e5.17 power dissipation (typical) versus rms on-state current figure e5.18 normalized dc latching current versus case temperature figure e5.19 simple test circuit for gate trigger voltage and current measurement note: v1 ? 0 v to 10 v dc meter v gt ? 0 v to 1 v dc meter i g ? 0 ma to 1 ma dc milliammeter r1 ? 1 k potentiometer to measure gate trigger voltage and current, raise gate voltage (v gt ) until meter reading v1 drops from 6 v to 1 v. gate trigger voltage is the reading on v gt just prior to v1 dropping. gate trig- ger current i gt can be computed from the relationship where i g is reading (in amperes) on meter just prior to v1 drop- ping. note: i gt may turn out to be a negative quantity (trigger current flows out from gate lead). 024681 0 0 2 4 6 8 10 12 rms on-state current [i t(rms) ] ? amps current waveform: half sine wave load: resistive or inductive conduction angle: 180? average on-state power dissipation [p d(av) ] ? watts 6 a to 10 a to-220, to-202, to-251, and to-252 -65 -15 +25 +65 +110 +125 -40 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 case temperature (t c ) ? ?c ratio of i l i l ( t c = 25 ?c) see general notes for specific device operating temperature range. v1 6 v dc + ? 100 d.u.t. reset normally-closed pushbutton 1 k (1%) i g v gt 100 i gt r1 in4001 i gt i g v gt 1000 ------------ - amps ? =
data sheets sensitive scrs ?2002 teccor electronics e5 - 11 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e5.20 peak repetitive capacitor discharge current figure e5.21 peak repetitive sinusoidal curve 180 160 140 120 100 80 60 40 20 0 1.0 3.0 5.0 7.0 10 30 50 70 100 peak discharge current (i tm ) ? amps peak current duration (t w ) ? s 0.8 a to 4 a i tm t w t w = 5 time constants 60 hz 12 hz 1 hz 180 160 140 120 100 80 60 40 20 0 1.0 3.0 5.0 7.0 10 30 50 70 100 peak discharge current (i tm ) ? amps peak current duration (t w ) ? s 0.8 a to 4 a i tm t w 60 hz 12 hz 1 hz
notes
?2002 teccor electronics e6 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 selected package s* u.l. recogn ized file #e71639 ak g scrs (1 a to 70 a) e6 general description the teccor line of thyristor scr semi-conductors are half-wave, unidirectional, gate-controlled rectifiers which complement tec- cor's line of sensitive scrs. teccor offers devices with ratings of 1 a to 70 a and 200 v to 1000 v, with gate sensitivities from 10 ma to 50 ma. if gate currents in the 12 a to 500 a ranges are required, see ?sensitive scrs? section of this catalog. three packages are offered in electrically isolated construction where the case or tab is internally isolated to allow the use of low-cost assembly and convenient packaging techniques. the teccor line of scrs features glass-passivated junctions to ensure long-term reliability and parameter stability. teccor?s glass offers a rugged, reliable barrier against junction contamina- tion. variations of devices covered in this data sheet are available for custom design applications. consult the factory for more informa- tion. features ? electrically-isolated package ? high voltage capability ? 200 v to 1000 v ? high surge capability ? up to 950 a ? glass-passivated chip compak scr ? surface mount package ? 1 a series ? new small profile three-leaded compak package ? packaged in embossed carrier tape with 2,500 devices per reel ? can replace sot-223 e6 to-92 * to-218 to-202 * to-218x 3-lead compak to-252 d-pak to-251 v-pak * to-220 to-263 d 2 pak
scrs data sheets http://www.teccor.com e6 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog specific test conditions di/dt ? maximum rate-of-rise of on-state current; i gt = 150 ma with 0.1 s rise time dv/dt ? critical rate of applied forward voltage i 2 t ? rms surge (non-repetitive) on-state current for period of 8.3 ms for fusing i drm and i rrm ? peak off-state forward and reverse current at v drm and v rrm i gt ? dc gate trigger current; v d = 12 v dc; r l = 60 ? for 1 to 16 a devices and 30 ? for 20 to 70 a devices i gm ? peak gate current i h ? dc holding current; gate open i t ? maximum on-state current i tsm ? peak one-cycle forward surge current p g(av) ? average gate power dissipation p gm ? peak gate power dissipation t gt ? gate controlled turn-on time; gate pulse = 100 ma; minimum width = 15 s with rise time 0.1 s t q ? circuit commutated turn-off time v drm and v rrm ? repetitive peak off-state forward and reverse voltage v gt ? dc gate trigger voltage; v d = 12 v dc; r l = 60 ? for 1 to 16 a devices and 30 ? for 20 to 70 a devices v tm ? peak on-state voltage at maximum rated rms current general notes ? all measurements are made at 60 hz with a resistive load at an ambient temperature of +25 c unless otherwise specified. ? operating temperature range (t j ) is -65 c to +125 c for to-92 devices and -40 c to +125 c for all other packages. ? storage temperature range (t s ) is -65 c to +150 c for to-92 devices, -40 c to +150 c for to-202 and to-220 devices, and -40 c to +125 c for all others. ? lead solder temperature is a maximum of 230 c for 10 seconds maximum; 1/16" (1.59 mm) from case. ? the case temperature (t c ) is measured as shown on dimensional outline drawings in the ?package dimensions? sectionof this catalog. type part number i t v drm & v rrm i gt isolated non-isolated to-92 to-220 to-202 to-220 to-251 v-pak compak to-252 d-pak (1) (2) (15) amps volts (4) mamps see ?package dimensions? section for variations. (11) i t(rms) i t(av) max max min min max 1a s201e s2n1 1 0.64 200 1 10 s401e s4n1 1 0.64 400 1 10 s601e s6n1 1 0.64 600 1 10 6a s2006l s2006f1 s2006v s2006d 6 3.8 200 1 15 s4006l s4006f1 s4006v s4006d 6 3.8 400 1 15 s6006l s6006f1 s6006v s6006d 6 3.8 600 1 15 s8006l s8006v s8006d 6 3.8 800 1 15 sk006l sk006v sk006d 6 3.8 1000 1 15 8a s2008l s2008f1 s2008r s2008v s2008d 8 5.1 200 1 15 s4008l s4008f1 s4008r s4008v s4008d 8 5.1 400 1 15 s6008l s6008f1 s6008r s6008v s6008d 8 5.1 600 1 15 s8008l s8008r s8008v s8008d 8 5.1 800 1 15 sk008l sk008r sk008v sk008d 8 5.1 1000 1 15 10 a s2010l s2010f1 s2010r s2010v s2010d 10 6.4 200 1 15 s4010l s4010f1 s4010r s4010v s4010d 10 6.4 400 1 15 s6010l s6010f1 s6010r s6010v s6010d 10 6.4 600 1 15 s8010l s8010r s8010v s8010d 10 6.4 800 1 15 sk010l sk010r sk010v sk010d 10 6.4 1000 1 15 12 a s2012r s2012v s2012d 12 7.6 200 1 20 s4012r s4012v s4012d 12 7.6 400 1 20 s6012r s6012v s6012d 12 7.6 600 1 20 s8012r s8012v s8012d 12 7.6 800 1 20 sk012r sk012v sk012d 12 7.6 1000 1 20 k g a k a g k a g a k a g a a a g k a g k a a k g
data sheets scrs ?2002 teccor electronics e6 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 electrical specification notes (1) see figure e6.5 through figure e6.16 for current rating at specified operating case temperature. (2) see figure e6.1 and figure e6.2 for free air current rating. (3) see figure e6.19 and figure e6.20 for instantaneous on-state current versus on-state voltage (typical). (4) see figure e6.18 for i gt versus t c . (5) see figure e6.17 for i h versus t c . (6) for more than one full cycle rating, see figure e6.23. (7) see figure e6.22 for t gt versus i gt . (8) see figure e6.21 for v gt versus t c . (9) test conditions are as follows: ?i t = 1 a for 1 a devices and 2 a for all other devices ? pulse duration = 50 s, dv/dt = 20 v/s, di/dt = -10 a/s for 1 a devices, and -30 a/s for other devices ?i gt = 200 ma at turn-on (10) see figure e6.5 through figure e6.10 for maximum allowable case temperatures at maximum rated current. (11) see package outlines for lead form configuration. when ordering special lead forming, add type number as suffix to part number. (12) pulse width 10 s (13) initial on-state current = 200 ma dc for 1 a through 16 a devices; 400 ma dc for 20 a through 70 a devices. (14) t c = t j for test conditions in off state. (15) the r, k, or m package rating is intended for high surge condition use only and not recommended for 50 a rms continuous current use since narrow pin lead temperature can exceed pcb solder melting temperature. teccor's j package or w package is recommended for 50 a rms continuous current requirements. (16) for various durations of an exponentially decaying current waveform, see figure e6.3 and figure e6.4. (t w is defined as 5 time constants.) (17) minimum non-trigger v gt at 125 c is 0.2 v. i drm & i rrm v tm v gt i h i gm p gm p g(av) i tsm dv/dt i 2 t di/dt t gt t q (14) mamps (3) volts (8) (17) volts (5) (13) mamps (12) amps (12) watts watts (6) (10) amps volts/sec amps 2 sec amps/sec (7) sec (9) (10) sec t c = 25 c t c = 100 c t c = 125 c t c = 25 c t c = 25 c 60/50 hz t c = 100 c t c = 125 c max max max max min min typ max 0.01 0.2 0.5 1.6 1.5 30 1.5 15 0.3 30/25 40 20 3.7 50 2 35 0.01 0.2 0.5 1.6 1.5 30 1.5 15 0.3 30/25 40 20 3.7 50 2 35 0.01 0.2 0.5 1.6 1.5 30 1.5 15 0.3 30/25 40 20 3.7 50 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 300 225 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 250 200 41 100 2 35 0.02 3 1.6 1.5 30 2 20 0.5 100/83 100 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 300 225 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 250 200 41 100 2 35 0.02 3 1.6 1.5 30 2 20 0.5 100/83 100 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35 0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 300 225 41 100 2 35 0.02 0.5 1 1.6 1.5 30 2 20 0.5 100/83 250 200 41 100 2 35 0.02 3 1.6 1.5 30 2 20 0.5 100/83 100 41 100 2 35 0.01 0.5 1 1.6 1.5 40 2 20 0.5 120/100 350 250 60 100 2 35 0.01 0.5 1 1.6 1.5 40 2 20 0.5 120/100 350 250 60 100 2 35 0.01 0.5 1 1.6 1.5 40 2 20 0.5 120/100 300 225 60 100 2 35 0.02 0.5 1 1.6 1.5 40 2 20 0.5 120/100 250 200 60 100 2 35 0.02 3 1.6 1.5 40 2 20 0.5 120/100 100 60 100 2 35
scrs data sheets http://www.teccor.com e6 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog see ?general notes? on page e6 - 2 and ?electrical specification notes? on page e6 - 3. type part number i t v drm & v rrm i gt i drm & i rrm isolated non-isolated to-220 to-218x to-218 to-220 to-218x to-218 to-263 d 2 pak (1) (15) amps volts (4) mamps (14) mamps i t(rms) i t(av) t c = 25 c t c = 100 c t c = 125 c see ?package dimensions? section for variations. (11) max min min max max 15 a s2015l 15 9.5 200 1 30 0.01 0.5 1 s4015l 15 9.5 400 1 30 0.01 0.5 1 s6015l 15 9.5 600 1 30 0.01 0.5 1 s8015l 15 9.5 800 1 30 0.02 1 2 sk015l 15 9.5 1000 1 30 0.02 3 16 a s2016r s2016n 16 10 200 1 30 0.01 0.5 1 s4016r s4016n 16 10 400 1 30 0.01 0.5 1 s6016r s6016n 16 10 600 1 30 0.01 0.5 1 s8016r s8016n 16 10 800 1 30 0.02 1 2 sk016r sk016n 16 10 1000 1 30 0.02 3 20 a s2020l 20 12.8 200 1 30 0.01 0.5 1 s4020l 20 12.8 400 1 30 0.01 0.5 1 s6020l 20 12.8 600 1 30 0.01 0.5 1 s8020l 20 12.8 800 1 30 0.02 1.0 2 sk020l 20 12.8 1000 1 30 0.02 3 25 a s2025l s2025r s2025n 25 16 200 1 35 0.01 1 2 s4025l s4025r s4025n 25 16 400 1 35 0.01 1 2 s6025l s6025r s6025n 25 16 600 1 35 0.01 1 2 s8025l s8025r s8025n 25 16 800 1 35 0.02 1.5 3 sk025l sk025r sk025n 25 16 1000 1 35 0.02 3 35 a s2035j s2035k 35 22 200 5 40 0.01 1 2 s4035j s4035k 35 22 400 5 40 0.01 1 2 s6035j s6035k 35 22 600 5 40 0.01 1 2 s8035j s8035k 35 22 800 5 40 0.02 1.5 3 sk035k 35 22 1000 5 40 0.02 3 40 a s2040r s2040n 40 25 200 5 40 0.01 1 2 s4040r s4040n 40 25 400 5 40 0.01 1 2 s6040r s6040n 40 25 600 5 40 0.01 1 2 s8040r s8040n 40 25 800 5 40 0.02 1.5 3 sk040r sk040n 40 25 1000 5 40 0.03 5 55 a s2055r s2055w s2055m s2055n 55 35 200 5 40 0.01 1 2 s4055r s4055w s4055m s4055n 55 35 400 5 40 0.01 1 2 s6055r s6055w s6055m s6055n 55 35 600 5 40 0.01 1 2 s8055r s8055w s8055m s8055n 55 35 800 5 40 0.02 1.5 3 sk055r sk055m sk055n 55 35 1000 5 40 0.03 5 65 a s2065j s2065k 65 41 200 5 50 0.02 1.5 3 s4065j s4065k 65 41 400 5 50 0.02 1.5 3 s6065j s6065k 65 41 600 5 50 0.02 1.5 3 s8065j s8065k 65 41 800 5 50 0.02 2 5 sk065k 65 41 1000 5 50 0.03 5 70 a s2070w 70 45 200 5 50 0.02 1.5 3 s4070w 70 45 400 5 50 0.02 1.5 3 s6070w 70 45 600 5 50 0.02 1.5 3 s8070w 70 45 800 5 50 0.02 2 5 k a g k a g a k g a k a g a k a g a a k a g a a a k g
data sheets scrs ?2002 teccor electronics e6 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 see ?general notes? on page e6 - 2 and ?electrical specification notes? on page e6 - 3. v tm v gt i h i gm p gm p g(av) i tsm dv/dt i 2 t di/dt t gt t q (3) volts (8) (17) volts (5) (13) mamps (12) amps (12) watts watts (6) (10) (16) amps volts/sec amps 2 sec amps/sec (7) sec (9) (10) sec t c = 25 c t c = 25 c 60/50 hz t c = 100 c t c = 125 c max max max min min typ max 1.6 1.5 40 3 30 0.6 225/188 450 350 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 450 350 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 425 325 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 400 300 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 200 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 450 350 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 450 350 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 425 325 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 400 300 210 125 2 35 1.6 1.5 40 3 30 0.6 225/188 200 210 125 2 35 1.6 1.5 40 3 30 0.6 300/255 450 350 374 125 2 35 1.6 1.5 40 3 30 0.6 300/255 450 350 374 125 2 35 1.6 1.5 40 3 30 0.6 300/255 425 325 374 125 2 35 1.6 1.5 40 3 30 0.6 300/255 400 300 374 125 2 35 1.6 1.5 40 3 30 0.6 300/255 200 374 125 2 35 1.6 1.5 50 3.5 35 0.8 350/300 450 350 510 150 2 35 1.6 1.5 50 3.5 35 0.8 350/300 450 350 510 150 2 35 1.6 1.5 50 3.5 35 0.8 350/300 425 325 510 150 2 35 1.6 1.5 50 3.5 35 0.8 350/300 400 300 510 150 2 35 1.6 1.5 50 3.5 35 0.8 350/300 200 510 150 2 35 1.8 1.5 50 3.5 35 0.8 500/425 450 350 1035 150 2 35 1.8 1.5 50 3.5 35 0.8 500/425 450 350 1035 150 2 35 1.8 1.5 50 3.5 35 0.8 500/425 425 325 1035 150 2 35 1.8 1.5 50 3.5 35 0.8 500/425 400 300 1035 150 2 35 1.8 1.5 50 3.5 35 0.8 500/425 200 1035 150 2 35 1.8 1.5 60 3.5 35 0.8 520/430 650 550 1122 175 2.5 35 1.8 1.5 60 3.5 35 0.8 520/430 650 550 1122 175 2.5 35 1.8 1.5 60 3.5 35 0.8 520/430 600 500 1122 175 2.5 35 1.8 1.5 60 3.5 35 0.8 520/430 500 475 1122 175 2.5 35 1.8 1.5 60 3.5 35 0.8 520/430 250 1122 175 2.5 35 1.8 1.5 60 4 40 0.8 650/550 650 550 1750 175 2.5 35 1.8 1.5 60 4 40 0.8 650/550 650 550 1750 175 2.5 35 1.8 1.5 60 4 40 0.8 650/550 600 500 1750 175 2.5 35 1.8 1.5 60 4 40 0.8 650/550 500 475 1750 175 2.5 35 1.8 1.5 60 4 40 0.8 650/550 250 1750 175 2.5 35 1.8 2 80 5 50 1 950/800 650 550 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 650 550 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 600 500 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 500 475 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 250 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 650 550 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 650 550 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 600 500 3745 200 2.5 35 1.8 2 80 5 50 1 950/800 500 475 3745 200 2.5 35
scrs data sheets http://www.teccor.com e6 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog * mounted on 1cm 2 copper foil surface; two-ounce copper foil electrical isolation teccor?s isolated scr packages will withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab over the device's operating temperature range. the following table shows standard and optional isolation ratings. * ul recognized file #e71639 ** for 4000 v isolation, use ?v? suffix in part number. thermal resistance (steady state) r jc [r ja ] c/w (typ.) pkg. code lf f2 r j wkm d v n type to-220 isolated to-202 type 1 non-isolated to-202 type 2 non-isolated to-220 non-isolated to-218x isolated to-218x non-isolated to-218 isolated to-218 non-isolated to-252 d-pak surface mount to-251aa v-pak non-isolated to-263 d 2 pak non-isolated 1a see below 6a 4.0 [50] 4.3 [45] 9.5 [70] 1.7 2.3 [70] 8a 3.4 3.9 1.8 [40] 1.5 2.0 10 a 3.0 3.4 1.6 1.45 1.7 12 a 1.5 1.4 1.6 15 a 2.5 16 a 1.3 1.3 20 a 2.4 25 a 2.35 1.0 1.0 35 a 0.70 0.70 40 a 0.6 0.6 55 a 0.5 0.53 0.53 0.5 65 a 0.86 0.86 70 a 0.60 thermal resistance (steady state) r jc [r ja ] c/w (typ.) package code ce type compak to-92 1a 35 * 50 [145] electrical isolation * from leads to mounting tab vacrms to-220 isolated to-218x isolated to-218 isolated 2500 standard standard standard 4000 optional ** n/a n/a
data sheets scrs ?2002 teccor electronics e6 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e6.1 maximum allowable ambient temperature versus rms on-state current figure e6.2 maximum allowable ambient temperature versus average on-state current figure e6.3 peak capacitor discharge current (6 a through 55 a) figure e6.4 peak capacitor discharge current derating (6 a through 55 a) figure e6.5 maximum allowable case temperature versus rms on-state current (1 a) figure e6.6 maximum allowable case temperature versus rms on-state current (6 a, 8 a, and 10 a) 20 40 60 80 100 120 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? free air rating rms on-state current [i t(rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c 8 a to -220 (non -isolated ) 6 a to -220 (isolate d) and 6 a to -202 (types 1 and 3) 1 a to -92 6 a to -202 (types 2 and 4) and 6 a to -251 20 40 60 80 100 120 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 maximum allowable ambient temperature (t a ) ? ?c average on-state current [i t(av) ] ? amps 8 a to-220 (non-isolated) 6 a to-220 (isolated) and 6 a to-202 (types 1 and 3) 1 a to-92 6 a to-202 (types 2 and 4) and 6 a to-251 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? free air rating 0.5 1.0 2.0 5.0 10 20 50 20 50 100 200 300 1000 pulse current duration (t w ) ? ms peak discharge current (i tm ) ? amps t w i tm t w = 5 times constants 6 a to 10 a devices 12 a devices 25 a devices 55 a devices 15 a and 16 a devices 25 50 75 100 125 0 0.2 0.4 0.6 0.8 1.0 case temperature (t c ) ? ?c normalized peak current 50 60 70 80 90 100 110 120 130 rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 0 0.4 0.8 1.2 0.6 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawing 1.0 0.2 1 a devices 024681012 50 60 70 80 90 100 110 120 130 current waveform: sinusoidal load: resistive or inductive conduction angle: 180o case temperature: measure as shown on dimensional drawings rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 8 a to-220 (isolated) and 8 a to-202 6 a devi ces 8 a to-220 (non-isolated ) to-251 and to -252 10 a to-220 (isolated ) and 10 a to-202
scrs data sheets http://www.teccor.com e6 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e6.7 maximum allowable case temperature versus rms on-state current (10 a, 12 a, 16 a, and 20 a) figure e6.8 maximum allowable case temperature versus rms on-state current (25 a and 35 a) figure e6.9 maximum allowable case temperature versus rms on-state current (40 a through 70 a) figure e6.10 maximum allowable case temperature versus rms on-state current (55 a and 65 a) figure e6.11 maximum allowable case temperature versus average on-state current (1 a) figure e6.12 maximum allowable case temperature versus average on-state current (8 a, 10 a, and 12 a) 04 8121620 50 60 70 80 90 100 110 120 130 rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawing 10 a to-220 (non-isolated) 15 a to-220 (isolated) 20 a to-220 (isolated) 16 a to-220 (non-isolated) and to-263 10 a to-251 and 10 a to-252 12 a to-220 (non-isolated) to- 251 and to-252 0 4 8 12162024283236 50 60 70 80 90 100 110 120 130 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 ? case temperature: measure as shown on dimensional drawings rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 35 a to-218 (isolated) 25 a to -220 (non-isolate d) and to -263 25 a to -220 (isolated ) 0 10203040506070 50 60 70 80 90 100 110 120 130 rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 65 a to-218x (isolated) 55 a to-218x (non-isolated) current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings 40 a to-220 (non-isolated) and to-263 70 a to-218x (non-isolated) 010203040 50 60 70 80 90 100 110 120 130 rms on-state current [i t(rms) ] ? amps maximum allowable case temperature (t c ) ? ?c 50 60 70 75 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings * the r, k or m package rating is intended only for high surge condition use and is not recommended for >50 a rms continuous current use, since narrow pin lead temperature can exceed pcb solder melting temperature. j or w packages are recommended for >50 a rms continuous current requirements. 65 a to-218ac (isolated) * 55 a to-218ac (non-isol ated) * 55 a to-220 (non-isolated) and to-263 * 0 0.2 0.4 0.6 0.8 50 60 70 80 90 100 110 120 130 current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c 1 a devic es 80 1 0 2345678 90 100 110 120 130 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings 6 a to-220 6 a to-202 6 a to-251 6 a to-252 8 a to -220 (i solated) 8 a to -202 10 a to -220 (isolated) and 10 a t o -202 8 a to-22 0 (non-isol ated) 12 a to -2 20 (non-isolated) and to-251 and to - 252 10 a to-251 10 a to-252 10 a to-220 (non-isolated)
data sheets scrs ?2002 teccor electronics e6 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e6.13 maximum allowable case temperature versus average on-state current (10 a through 20 a) figure e6.14 maximum allowable case temperature versus average on-state current (25 a and 35 a) figure e6.15 maximum allowable case temperature versus average on-state current (40 a through 70 a) figure e6.16 maximum allowable case temperature versus average on-state current (55 a and 65 a) figure e6.17 normalized dc holding current versus case temperature figure e6.18 normalized dc gate-trigger current versus case temperature 02468101214 50 60 70 80 90 100 110 120 130 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measured as shown on dimensional drawings 20 a to-220 (isolated) 15 a to-220 (isolated) 10 a to-220 (non-isolated) 16 a to- 220 (non-isolated) an d to- 263 0 .4 8 12 16 20 24 50 60 70 80 90 100 110 120 130 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings 35 a to-218 (non-isolated) 35 a to-218 (isolated) 25a to - 220 (non-isolate d) and to - 263 25a to- 220 (isolated) 0 1020304050 50 60 70 80 90 100 110 120 130 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings 70 a to-218x (non-isolated) 40 a to-220 (non-isolated) and to-263 55 a to-218x (non-isolated) 65 a to-218x (isolated) 0 102030405 0 50 60 70 80 90 100 110 120 130 average on-state current [i t(av) ] ? amps maximum allowable case temperature (t c ) ? ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 180? case temperature: measure as shown on dimensional drawings 55 a to-218ac (non-isolated) * * the r, k, or m package rating is intended only for high surge condition use and is not recommended for >32 a (av) continuous current use since narrow pin lead temperature can exceed pcb solder melting temperature. j or w packages are recommended for >32 a (av) continuous current requirements. 55 a to-220 (non-isolated) and to-263 * 65 a to-218ac (isolated) * -40 -15 +25 +65 +105 +125 0 .5 1.0 1.5 2.0 case temperature (t c ) ? ?c ratio of i h i h (t c = 25 ?c) initial on-state current = 200 ma dc for 1 a to 20 a devices and 400 ma dc for 25 a to 70 a devices -40 -15 +25 +65 +105 +125 0 0.5 1.0 1.5 2.0 case temperature (t c ) ? ?c ratio of i gt i gt (t c = 25 ?c)
scrs data sheets http://www.teccor.com e6 - 10 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e6.19 instantaneous on-state current versus on-state voltage (typical) (6 a through 25 a) figure e6.20 instantaneous on-state current versus on-state voltage (typical) (35 a through 70 a) figure e6.21 normalized dc gate-trigger voltage versus case temperature figure e6.22 typical turn-on time versus gate-trigger current 0 0.6 0.8 1.0 1.2 1.4 1.6 0 10 20 30 40 50 60 70 80 90 instantaneous on-state voltage (v t ) ? volts instantaneous on-state current ( i t ) ? amps t c = 25?c 12 a devices 15 a to 20 a devices 1 a devices 6 a to 10 a devices 25 a devices 0 .6 .8 1.0 1.2 1.4 1.6 0 20 40 60 80 100 120 140 160 180 200 instantaneous on-state voltage (v t ) ? volts instantaneous on-state current ( i t ) ? amps t c = 25?c 65 a and 70 a devices 55 a devices 35 a to 40 a devices -40 -15 +25 +65 +105 +125 0 0.5 1.0 1.5 case temperature (t c ) ? ?c ratio of v gt v gt (t c = 25 ?c) 10 20 30 40 50 60 80 100 200 1 2 3 4 5 6 7 0 turn-on time (t gt ) ? s dc gate trigger current (i gt ) ? ma 6 a to 12 a devices 1 a devices 40 a to 70 a devices 15 a to 35 a devices t c = 25?c
data sheets scrs ?2002 teccor electronics e6 - 11 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e6.23 peak surge current versus surge current duration figure e6.24 power dissipation (typical) versus rms on-state current (1 a) figure e6.25 power dissipation (typical) versus rms on-state current (6 a through 20 a) 8 1 2 3 4 5 6 1000 10 20 30 40 50 60 80 100 200 300 400 500 600 800 1 23 5 4 6 7 8 10 20 30 40 60 80100 200 300400 600 1000 surge current duration ? full cycles 70 a de vices 65 a to- 218 55 a devices 25 a devices 35 a devices 20 a devices 16 a devices 15 a devices 12 a devices 10 a dev ices 1 a de vices supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: max- rated value at specified case temperature notes: 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. 8 a devices 6 a devices peak surge (non-repetitive) on-state current (i tsm ) ? amps 40 a devi ces 0 0.2 0.4 0.6 0.8 0 0.4 0.8 1.0 0.2 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: half sine wave load: resistive or inductive conduction angle: 180? 1.0 a devices 1.0 0.6 0481216 0 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: half sine wave load: resistive or inductive conduction angle: 180? 2 6 10 14 18 2 4 6 8 10 12 14 16 18 20 15 a to 20 a devices 12 a devices 6 a to 10 a devices
scrs data sheets http://www.teccor.com e6 - 12 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e6.26 power dissipation (typical) versus rms on-state current (25 a and 35 a) figure e6.27 power dissipation (typical) versus rms on-state current (40 a through 70 a) 0 8 16 24 32 0 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] x? watts 412202836 4 8 12 16 20 24 28 32 25 a to-220 devices 35 a devi ces current waveform: half sine wave load: resistive or inductive conduction angle: 180? rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts 0 10203040506070 0 10 20 30 40 50 60 65 a and 70 a devices current waveform: half sine wave load: resistive or inductive conduction angle: 180? 40 a and 55 a devi ces
u.l. recogn ized file #e7163 9 to-220 isolated ac ?2002 teccor electronics e7 - 1 http://www.teccor.com thyristor product catalog + 1 972-580-7777 rectifiers (15 a to 25 a) e7 general description teccor manufactures 15 a rms to 25 a rms rectifiers with volt- ages rated from 200 v to 1000 v. due to the electrically-isolated to-220 package, these rectifiers may be used in common anode or common cathode circuits using only one part type, thereby simplifying stock requirements. teccor's silicon rectifiers feature glass-passivated junctions to ensure long term reliability and stability. in addition, glass offers a rugged, reliable barrier against junction contamination. features ? electrically-isolated packages ? high voltage capabilities ? 200 v to 1000 v ? high surge capabilities ? up to 350 a ? glass-passivated junctions e7
http://www.teccor.com e7 - 2 ?2002 teccor electronics + 1 972-580-7777 thyristor product catalog rectifiers data sheets test conditions i 2 t ? rms surge (non-repetitive) forward current for 8.3 ms for fusing i f(av) ? average forward current i f(rms) ? rms forward current i fsm ? peak one-cycle surge current i rm ? peak reverse current r jc ? thermal resistance (steady state) junction to case v fm ? peak forward voltage at rated average forward current v r ? dc blocking voltage v rrm ? peak repetitive reverse voltage general notes ? operating temperature range (t j ) is -40 c to +125 c. ? storage temperature range (t s ) is -40 c to +125 c. ? lead solder temperature is a maximum of 230 c for 10 seconds maximum at a minimum of 1/16" (1.59 mm) from case. ? the case temperature (t c ) is measured as shown on dimensional outline drawings in the ?pack age dimensions? section of this catalog. ? teccor's electrically-isolated to-220 devices withstand a high potential test of 2500 v ac rms from leads to mounting tab over the operating temperature range. ? typical reverse recovery time (t rr ) is 4 s. (test conditions = 0.9 a forward current and 1.5 a reverse current) electrical specification notes (1) see figure e7.3 for current rating at specified case temperature. (2) for more than one full cycle rating, see figure e7.4. (3) t c = t j for test conditions (4) see package outlines for lead form configurations. when ordering special lead forming, add type number as suffix to part number. electrical isolation * ul recognized file #e71639 ** for 4000 v isolation, use ?v? suffix in the part number. type part number v rrm v r i f(av) i f(rms) i fsm i rm v fm i 2 t r jc isolated to-220 volts volts (1) amps amps (2) amps (3) ma volts amps 2 sec c/w 60/50 hz t c = 25 c t c = 100 c t c = 125 ct c =25 c see ?package dimensions? section for variations. (4) min min max max max max typ 15 a d2015l 200 200 9.5 15 225/188 0.1 0.5 1 1.6 210 2.85 d4015l 400 400 9.5 15 225/188 0.1 0.5 1 1.6 210 2.85 d6015l 600 600 9.5 15 225/188 0.1 0.5 1 1.6 210 2.58 d8015l 800 800 9.5 15 225/188 0.1 0.5 1 1.6 210 2.85 dk015l 1000 1000 9.5 15 225/188 0.1 3 1.6 210 2.85 20 a d2020l 200 200 12.7 20 300/255 0.1 0.5 1 1.6 374 2.5 d4020l 400 400 12.7 20 300/255 0.1 0.5 1 1.6 374 2.5 d6020l 600 600 12.7 20 300/255 0.1 0.5 1 1.6 374 2.5 d8020l 800 800 12.7 20 300/255 0.1 0.5 1 1.6 374 2.5 dk020l 1000 1000 12.7 20 300/255 0.1 3 1.6 374 2.5 25 a d2025l 200 200 15.9 25 350/300 0.1 0.5 1 1.6 508 2.7 d4025l 400 400 15.9 25 350/300 0.1 0.5 1 1.6 508 2.7 d6025l 600 600 15.9 25 350/300 0.1 0.5 1 1.6 508 2.7 d8025l 800 800 15.9 25 350/300 0.1 0.5 1 1.6 508 2.7 dk025l 1000 1000 15.9 25 350/300 0.1 3 1.6 508 2.7 c a not used electrical isolation from leads to mounting tab * vacrms to-220 isolated 2500 standard 4000 optional **
?2002 teccor electronics e7 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets rectifiers figure e7.1 instantaneous forward current versus forward voltage (typical) figure e7.2 forward power dissipation (typical) figure e7.3 maximum allowable case temperature versus average forward current figure e7.4 peak surge forward current versus surge current duration 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 20 40 60 80 100 120 140 instantaneous forward voltage (v f ) ? volts instantaneous forward current ( i f ) ? amps 15 a devices t c = 25?c 20 a devices 25 a devices 16 12 0 2 4 6 8 101214 0 4 8 12 16 20 single pulse rectification 60 hz sine wave 20 a devices 15 a devices 25 a devices average forward current [i f(av) ] ? amps average forward power d issipation [p f(av) ] ? watts 02468101214 0 70 75 80 85 90 95 100 105 110 115 120 125 20 a devices 15 a devices average forward current [i f (av) ] ? amps maximum allowable case temperature (t c ) ? ?c supply frequency: 60 hz sine wave load: resistive or inductive case temperature: measured as shown on dimensional drawing 16 25 a devices 10 20 30 40 60 80 100 200 300 400 600 800 1000 1 2 4 6 10 20 40 60 100 200 400 600 1000 surge current duration ? cycles supply frequency: 60 hz sinewave load: resistive or inductive rms on-state current: [i f(rms) ] maximium rated value at specified case temperature 15 a devices 20 a devices 25 a devices peak surge (non-repetitive) forward current (i fsm ) ? amps
notes
? 2002 teccor electronics e8 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 diac ht and st series e8 general description teccor?s ht and st series of bilateral trigger diacs offer a range of voltage characteristics from 27 v to 45 v. a diac semiconductor is a full-wave or bidirectional thyristor. it is triggered from a blocking- to conduction-state for either polarity of applied voltage whenever the amplitude of applied voltage exceeds the breakover voltage rating of the diac. the teccor line of diacs features glass-passivated junctions to ensure long-term reliability and parameter stability. teccor?s glass offers a rugged, reliable barrier against junction contamination. the diac specifications listed in this data sheet are for standard products. special parameter selections such as close tolerance voltage symmetry are available. consult the factory for more information about custom design applications. features ? bilateral triggering device ? glass-passivated junctions ? wide voltage range selections st series ? epoxy smt package ? high-temperature, solder-bonded die attachment ht series ? do-35 trigger package ? pre-tinned leads e8 do-214 do-35
diac data sheets http://www.teccor.com e8 - 2 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog general notes ? lead solder temperature is +230 c for 10-second maximum; 1/16" (1.59 mm) from case. ? see ?package dimensions? section of this catalog. electrical specification notes (1) breakover voltage symmetry as cl ose as 1 v is available from the factory on these products. (2) see figure e8.4 and figure e8.5 for test circuit and waveforms. (3) typical switching time is 900 nano-seconds measured at i pk (figure e8.4) across a 20 ? resistor (figure e8.5). switching time is defined as rise time of i pk between the 10% to 90% points. (4) see v-i characteristics. bilateral trigger diac specifications ? maximum ratings, absolute-maximum values ? maximum trigger firing capacitance: 0.1 f ? device dissipation (at t a = -40 c to +40 c): 250 mw for do-35 and 300 mw for do-214 ? derate above +40 c: 3.6 mw/c for do-35 and 3 mw/c for do-214 ? temperature ranges storage: -40 c to +125 c operating (junction): -40 c to +125 c v-i characteristics * mounted on 1 cm 2 copper foil surface; two-ounce copper foil electrical characteristics t c = 25c part no. v bo ? v bo v bb i bo i trm do-35 do-214 breakover voltage (forward and reverse) volts breakover voltage symmetry ? v bo = [ | +v bo | - | - v bo | ] volts dynamic breakback voltage (3) | ? v | volts peak breakover current at breakover voltage amps peak pulse current for 10 s 120 pps t a 40 c amps min max max min max max ht-32 st-32 27 37 3 (1) 10 (2) 25 2 ht-32a / ht-5761 28 36 2 (1) 7 at 10 ma (4) 25 2 ht-32b / ht-5761a st-32b 30 34 2 (1) 7 at 10 ma (4) 25 2 ht-34b st-34b 32 36 2 (1) 10 (2) 25 2 ht-35 st-35 30 40 3 (1) 10 (2) 25 2 ht-36a / ht-5762 st-36a 32 40 2 (1) 7 at 10 ma (4) 25 2 ht-36b st-36b 34 38 2 (1) 10 (2) 25 2 ht-40 st-40 35 45 3 (1) 10 (2) 25 2 ht and st series thermal resistance junction to lead - r jl : c/w junction to ambient [r ja ]: c/w (based on maximum lead temperature of 90 c for do-214 and 85 c for do-35 devices) y package do-35 s package do-214 100 [278] c/w 65 c/w * 10 ma breakover current i bo -v bo voltage current breakover voltage v bo +v bo v
data sheets diac ? 2002 teccor electronics e8 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e8.1 typical diac/triac full-wave phase control circuit using lower voltage diacs. figure e8.2 repetitive peak on-state current versus pulse duration 120 v ac 60 hz load ? up to 1500 w 3.3 k 200 k 0.1 f 100 v ht-35 bilateral trigger diac triac q2015l5 mt2 mt1 g 12 4 6 200 400 6001000 2000 4000 10000 .001 .002 .003 .005 0.1 0.2 0.3 3.0 0.5 5.0 .01 0.02 0.03 0.05 1.0 10 2.0 repetitive peak on-state current (i trm ) ? amps base pulse duration ? s safe operating area 10 20 40 60 100 pulse repetition rate = 120 pps t a = 40 ?c
diac data sheets http://www.teccor.com e8 - 4 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog figure e8.3 normalized v bo change versus junction temperature figure e8.4 test circuit waveforms (refer to figure e8.5.) figure e8.5 circuit used to measure diac characteristics (refer to figure e8.4.) figure e8.6 peak output current versus triggering capacitance (per figure e8.5 with r l of 20 ? ) -8 -6 -4 -2 0 +2 +4 +6 +8 -40 -20 0 +20 +40 +60 +80 +100 +120 +140 junction temperature (t j ) ? ?c percentage of v bo change ? % st series ht series ? v+ ? v- v c 0 -v bo i l +i pk 0 t -i pk t +v bo typical pulse base width is 10 s 120 v rms 60 hz 47 k d.u.t. r l 20 ? 1% v c 100 k * c t i l o.1 f * adjust for one firing in each half cycle. d.u.t. = diac triggering capacitance (c t ) ? f peak output current (i pk ) ? ma .01 .02 .03 .04 .05 .06 .07 .08 .09 0 50 100 150 200 250 300 typical ( 35 v dev ice) .10
?2002 teccor electronics e9 - 1 http://www.teccor.com thyristor product catalog + 1 972-580-7777 sidac (79 v to 330 v) e9 general description the sidac is a silicon bilateral voltage triggered switch with greater power-handling capabilities than standard diacs. upon application of a voltage exceeding the sidac breakover voltage point, the sidac switches on through a negative resistance region to a low on-state voltage. conduction continues until the current is interrupted or drops below the minimum holding current of the device. teccor?s sidacs feature glass-passivated junctions to ensure a rugged and dependable device capable of withstanding harsh environments. variations of devices covered in this data sheet are available for custom design applications. consult the factory for more informa- tion. applications ? high-voltage lamp ignitors ? natural gas ignitors ? gas oil ignitors ? high-voltage power supplies ? xenon ignitors ? overvoltage protector ? pulse generators ? fluorescent lighting ignitors ? hid lighting ignitors features ? ac circuit oriented ? glass-passivated junctions ? high surge current capability e9 to-92 type 70 do-214 surface mount to-202 do-15x
http://www.teccor.com e9 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog sidac data sheets specific test conditions di/dt ? critical rate-of-rise of on-state current dv/dt ? critical rate-of-rise of off-state voltage at rated v drm ; t j 100 c i bo ? breakover current 50/60 hz sine wave i drm ? repetitive peak off-state current 50/60 hz sine wave; v = v drm i h ? dynamic holding current 50/60 hz sine wave; r = 100 ? i t(rms) ? on-state rms current t j 125 c 50/60 hz sine wave i tsm ? peak one-cycle surge current 50/60 hz sine wave (non- repetitive) r s ? switching resistance 50/60 hz sine wave v bo ? breakover voltage 50/60 hz sine wave v drm ? repetitive peak off-state voltage v tm ? peak on-state voltage; i t = 1 a general notes ? all measurements are made at 60 hz with a resistive load at an ambient temperature of +25 c unless otherwise specified. ? storage temperature range (t s ) is -65 c to +150 c. ?the case (t c ) or lead (t l ) temperature is measured as shown on the dimensional outline drawings in the ?package dimensions? sec- tion of this catalog. ? junction temperature range (t j ) is -40 c to +125 c. ? lead solder temperature is a maximum of +230 c for 10-second maximum; 1/16" (1.59 mm) from case. electrical specification notes (1) see figure e9.5 for v bo change versus junction temperature. (2) see figure e9.6 for i bo versus junction temperature. (3) see figure e9.2 for i h versus case temperature. (4) see figure e9.13 for test circuit. (5) see figure e9.1 for more than one full cycle rating. (6) t c 90 c for to-92 sidac t c 105 c for to-202 sidacs t l 100 c for do-15x t l 90 c for do-214 (7) see figure e9.14 for clarification of sidac operation. (8) for best sidac operation, the load impedance should be near or less than switching resistance. (9) see package outlines for lead form configurations. when ordering special lead forming, add type number as suffix to part number. (10) do not use electrically connected mounting tab or center lead. v-i characteristics type part no. i t(rms) v drm v bo i drm i bo i h to-92 do-15x (10) to-202 do-214 (7) (8) amps volts (1) volts amps (2) amps (3) (4) mamps see ?package dimensions? section for variations. (9) max min min max max max typ max k0900e70 k0900g k0900s 1 70 79 97 5 10 60 150 k1050e70 k1050g k1050s 1 90 95 113 5 10 60 150 k1100e70 k1100g k1100s 1 90 104 118 5 10 60 150 k1200e70 k1200g k1200s 1 90 110 125 5 10 60 150 k1300e70 k1300g k1300s 1 90 120 138 5 10 60 150 k1400e70 k1400g k1400s 1 90 130 146 5 10 60 150 k1500e70 k1500g k1500s 1 90 140 170 5 10 60 150 k2000e70 k2000g k2000f1 k2000s 1 180 190 215 5 10 60 150 k2200e70 k2200g k2200f1 k2200s 1 180 205 230 5 10 60 150 k2400e70 k2400g k2400f1 k2400s 1 190 220 250 5 10 60 150 k2500e70 k2500g k2500f1 k2500s 1 200 240 280 5 10 60 150 k3000f1 1 200 270 330 5 10 60 150 r s v bo v s ? () i s i bo ? () -------------------------------- = -v +i v drm +v v s i s i h r s i drm i bo v bo v t i t (i s - i bo ) (v bo - v s ) r s = -i
?2002 teccor electronics e9 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets sidac * mounted on 1 cm 2 copper foil surface; two-ounce copper foil ** r ja for to-202 type 23 and type 41 is 70 c/watt. figure e9.1 peak surge current versus surge current duration figure e9.2 normalized dc holding current versus case/lead temperature v tm i tsm r s dv/dt di/dt volts max (5) amps (8) k ? volts/sec amps/sec package 60 hz 50 hz egfs min min typ 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 1.5 20 16.7 0.1 1500 150 1.5 1.5 3 1.5 20 16.7 0.1 1500 150 1.5 1.5 3 1.5 20 16.7 0.1 1500 150 1.5 1.5 3 1.5 20 16.7 0.1 1500 150 1.5 1.5 3 1.5 20 16.7 0.1 1500 150 3 20 16.7 0.1 1500 150 thermal resistance (steady state) r jc [r ja ] c/w (typical) e package g package f package s package 35 [95] 18 [75] 7 [45] ** 30 * [85] 1.0 10 100 1000 1.0 2.0 4.0 6.0 8.0 10 20 40 supply frequency: 60 hz sinusoidal load: resistive rms on-state current: i t rms maximum rated value at specified junction temperature notes: 1) blocking capability may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. sur g e current duration ? full cycles peak surge (non-repetitive) on-state current [i tsm ] ? amps 100 0 .5 1.0 2.0 1.5 -15 -40 +25 +65 +105 +125 case temperature (t c ) ? ? c i h i h (t c = 25 ? c) ratio of
http://www.teccor.com e9 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog sidac data sheets figure e9.3 repetitive peak on-state current (i trm ) versus pulse width at various frequencies figure e9.4 maximum allowable ambient temperature versus on-state current figure e9.5 normalized v bo change versus junction temperature figure e9.6 normalized repetitive peak breakover current versus junction temperature figure e9.7 on-state current versus on-state voltage (typical) figure e9.8 power dissipation (typical) versus on-state current [refer to figure e9.14 for basic sidac circuit] di/dt lim it line 0.6 0.8 4 2 4 6 8 10 20 40 60 80 100 200 400 600 2 x 10-3 68 1 x 10-2 2468 1 x 10-1 24681 1 pulse base width (t o ) ? ms repetitive peak on-state current (i trm ) ? amps v bo firing current waveform n on-r epeate d repe tition freq uency f=5 hz f = 10 hz f = 100 h z f = 1 khz f = 5 khz f = 10 khz f = 20 khz t j = 125 oc max to i trm l/f n on-r epeate d 0 0.2 0.4 0.6 0.8 1.0 20 40 60 80 100 120 140 25 rms on-state current [i t(rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c current waveform: sinusoidal - 60 hz load: resistive or inductive free air rating t o -9 2 a n d d o -2 1 4 do-15x and to-202 t ype 23 and 41 to-202 type 1 -12 -20 0 +20 +40 +60 +80 +100 +120 -10 -8 -6 -4 -2 0 +2 +4 -40 +25 junction temperature (t j ) ? ?c percentage of v bo change ? % +140 k2xxxf1 k1xxxe k1xxxg k1xxxs k2xxxe k2xxxg k2xxxs 20 30 40 50 60 80 70 90 100 110 120 1 2 3 4 5 6 7 8 9 junction temperature (t j ) ? ? c repetitive peak breakover current (i bo ) multiplier v = v bo 130 0 0.8 1.2 1.0 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3. 6 0 1 2 3 4 5 6 7 8 9 positive or negative instantaneous on-state voltage (v t ) ? volts positive or negative instantaneous on-state current (i t ) ? amps t l = 25 ?c to-92, do-214 and do-15x "e", "s" and "g" packages to-202 "f" package 0.2 0.4 0.6 0.8 1.0 0 0.4 0.8 1.2 1.6 0.2 0.6 1.0 1.4 1.8 2.0 2.2 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts "e", "s" and "g" packages to-92, do-214 and do-15x to-202 "f" package current waveform: sinusoidal load: resistive or inductive conduction angle: see basic sidac cirucit
?2002 teccor electronics e9 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets sidac figure e9.9 comparison of sidac versus scr for gas ignitor circuit figure e9.10 circuit (low voltage input) for gas ignition figure e9.11 typical high pressu re sodium lamp firing circuit figure e9.12 xenon lamp flashing circuit figure e9.13 dynamic holding current test circuit for sidacs figure e9.14 basic sidac circuit 100-250 v ac 60 hz 100-250 v ac 60 hz scr sidac 4.7 f 100 v 10 f 50 v 24 v ac 60 hz 4.7 f 100 v ? w k1200e sidac 200 v h.v. ignitor 1.2 f 4.7 k - + - + + - sidac 120 v ac 60 hz 16 mh 3.3 k 0.47 f 400 v ballast sidac 220 v ac 60 hz 7.5 k 0.22 f ballast lamp 120 v ac 220 v ac lamp - + + - xenon lamp k2200g 10 f 2 w 120 v ac 60 hz 10 f 450 v 4 kv 0.01 f 400 v 20 m sidac 200- 400 v 100 250 v trigger transformer 20:1 100-250 v ac 60 hz scope push to test s1 switch to test in each direction 100 ? 1% device under test s1 scope indication trace stops i h i pk load 100-250 v ac 60 hz i h v bo 120-145 ? conduction angle i h i h load current v bo v bo
http://www.teccor.com e9 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog sidac data sheets figure e9.15 relaxation oscillator using a sidac figure e9.16 sidac added to protect transistor for typical transistor inductive load switching requirements v dc(in) v b0 v c i l r l r sidac (a) circuit r max v in - v bo i bo r min v in - v tm i h (min) (b) waveforms v bo v c i l t t c v ce monitor 100 mh i c monitor + - r s = 0.1 ? test circuit v bb1 =10 v + - v bb2 =0 r bb2 = 100 ? r bb1 = 150 ? 2n6127 (or equivalent) 50 ? 50 ? input (see note b) tip-47 v cc = 20 v voltage and current waveforms input voltage 0 v 5 v 0.63 a 0 sidac v bo 10 v v ce(sat) t w 3 ms (see note a) collector current collector voltage 100 ms t w note a: input pulse width is increased until i cm = 0.63 a. note b: sidac (or diac or series of diacs) chosen so that v bo is just below v ceo rating of transistor to be protected. the sidac (or diac) eliminates a reverse breakdown of the transistor in inductive switching circuits where otherwise the transistor could be destroyed.
? 2002 teccor electronics m1 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 package dimensions m1 this section contains the dimensions for the following packages: ? f package ? to-202ab, type 1 (non-isolated) ? y package ? do-35 or do-204ah ? r package ? to-220ab (non-isolated) ? l package ? to-220ab (isolated) ? p package ? to-3 fastpak (isolated) ? e package ? to-92 (isolated) ? s package ? do-214aa ? m package ? to-218ac (non-isolated) ? k package ? to-218ac (isolated) ? w package ? to-218x (non-isolated) ? j package ? to-218x (isolated) ? g package ? do-15x axial lead ? c package ? compak ? n package ? to-263 ? d package ? to-252 ? v package ? to-251 m1
package dimensions data sheets http://www.teccor.com m1 - 2 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog f package ? to-202ab, type 1 non-isolated mounting tab common with mt2 / anode / pin 2 y package ? do-35 or do-204ah (1) package contour optional within dimensions a and c. slugs, if any, shall be included within this cylinder but shall not be subject to the minimum limit of dimension a. (2) lead diameter is not controlled in this zone to allow for flash, lead finish build-up, and minor irregularities other than slugs. n p q s 0.070 x 45 ? chamfer common t o all types l k j m mt1 / cathode / pin 1 mt2 / anode / pin 2 case temperature measurement point tab common to mt2 / anode / pin 2 a b c d g f h e notes: (1) maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm) (2) pin 2 and mounting tab are electrically connected. do not use either for sidac o p eration. gate / trigger / pin 3 r dia. dimension inches millimeters min max min max a 0.365 0.385 9.27 9.78 b 0.243 0.253 6.17 6.43 c 0.110 0.120 2.79 3.05 d 0.780 0.810 19.81 20.57 e 0.290 0.310 7.37 7.87 f 0.400 0.430 10.16 10.92 g 0.052 0.062 1.32 1.58 h 0.055 0.065 1.40 1.65 j 0.023 0.029 0.58 0.74 k 0.095 0.105 2.41 2.67 l 0.195 0.205 4.95 5.21 m 0.049 0.059 1.24 1.50 n 0.017 0.023 0.43 0.58 p 0.055 0.065 1.40 1.65 q 0.175 0.185 4.45 4.70 r 0.124 0.130 3.15 3.30 s 0.390 0.405 9.91 10.29 c b a dia. 1 1 2 d dia. typ e typ b dimension inches millimeters min max min max a 0.060 0.090 1.530 2.280 b 0.015 0.381 c 0.135 0.165 3.430 4.190 d 0.018 0.022 0.458 0.558 e 1.000 25.400
data sheets package dimensions ? 2002 teccor electronics m1 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 r package ? to-220ab non-isolated mounting tab common with center lead l package ? to-220ab isolated mounting tab a o p n m h l j k g f e dia. b c d case temperature measurement point gate/trigger * mt2 / anode mt1 / cathode note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). * the gate pin is not used on diode rectifiers. r package mt2 / anode r notch in gate lead identifies non-isolated tab dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.66 2.92 c 0.230 0.250 5.85 6.35 d 0.590 0.620 14.98 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.80 3.30 g 0.540 0.575 13.71 14.60 h 0.025 0.035 0.63 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.070 0.085 1.78 2.16 n 0.018 0.024 0.45 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.53 r 0.038 0.048 0.97 1.22 a o p n m h l j k g f e dia. b c d case temperature measurement point gate/trigger * mt2 / anode mt1 / cathode note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). * the gate pin is not used on diode rectifiers. r package mt2 / anode r dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.66 2.92 c 0.230 0.250 5.85 6.35 d 0.590 0.620 14.98 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.80 3.30 g 0.540 0.575 13.71 14.60 h 0.025 0.035 0.63 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.070 0.085 1.78 2.16 n 0.018 0.024 0.45 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.53 r 0.038 0.048 0.97 1.22
package dimensions data sheets http://www.teccor.com m1 - 4 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog p package ? to-3 fastpak isolated mounting base note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). e package ? to-92 all leads insulated from case. case is electrically nonconductive. mt2 gate mt1 g
t c measuring point dimension inches millimeters min max min max a 1.531 1.543 38.90 39.20 b 1.177 1.185 29.90 30.10 c 0.843 0.850 21.40 21.60 d 0.780 0.795 19.80 20.20 e 0.783 0.791 19.90 20.10 f 0.874 0.906 22.20 23.00 g 0.161 0.169 4.10 4.30 h 0.386 0.465 9.80 11.80 i 0.508 0.587 12.90 14.90 j 0.079 0.087 2.00 2.20 k 0.047 0.055 1.20 1.40 l 0.307 0.319 7.80 8.10 m 0.372 0.396 9.45 10.05 n 0.043 0.059 1.10 1.50 o 0.315 0.331 8.00 8.40 p 0.098 0.106 2.50 2.70 q 0.846 0.886 21.50 22.50 r 0.244 0.256 6.20 6.50 s 0.106 0.130 2.70 3.30 t (mt1) 0.321 0.329 8.15 8.35 t (mt2) 0.321 0.329 8.15 8.35 t (gate) 0.220 0.228 5.60 5.80 u (mt1) 0.246 0.254 6.25 6.45 u (mt2) 0.246 0.254 6.25 6.45 u (gate) 0.183 0.191 4.65 4.85 v 0.120 0.130 3.05 3.30 w 0.175 0.185 4.45 4.70 a b t c measuring point gate / pin 2 anode / mt2 / pin 3 cathode / mt1 / pin 1 e h g f d k j l m dimension inches millimeters min max min max a 0.176 0.196 4.47 4.98 b 0.500 12.70 d 0.095 0.105 2.41 2.67 e 0.150 3.81 f 0.046 0.054 1.16 1.37 g 0.135 0.145 3.43 3.68 h 0.088 0.096 2.23 2.44 j 0.176 0.186 4.47 4.73 k 0.088 0.096 2.23 2.44 l 0.013 0.019 0.33 0.48 m 0.013 0.017 0.33 0.43
data sheets package dimensions ? 2002 teccor electronics m1 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 s package ? do-214aa m package ? to-218ac non-isolated mounting tab common with center lead k package ? to-218ac isolated mounting tab 0.079 (2.0) 0.110 (2.8) 0.079 (2.0) pad outline h k j e f l g a c b d t c / t l temperature measurement point dimensions are in inches (and millimeters). dimension inches millimeters min max min max a 0.140 0.155 3.56 3.94 b 0.205 0.220 5.21 5.59 c 0.077 0.083 1.96 2.11 d 0.166 0.180 4.22 4.57 e 0.036 0.056 0.91 1.42 f 0.073 0.083 1.85 2.11 g 0.004 0.008 0.10 0.20 h 0.077 0.086 1.96 2.18 j 0.043 0.053 1.09 1.35 k 0.008 0.012 0.20 0.30 l 0.027 0.049 0.69 1.24 c d h g f b a e t c measurement point u dia. m package mt2 / anode p gate / pin 3 j mt2 / anode / pin 2 mt1 / cathode / pin 1 m n 3 times k l r q note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). w dimension inches millimeters min max min max a 0.810 0.835 20.57 21.21 b 0.610 0.630 15.49 16.00 c 0.178 0.188 4.52 4.78 d 0.055 0.070 1.40 1.78 e 0.487 0.497 12.37 12.62 f 0.635 0.655 16.13 16.64 g 0.022 0.029 0.56 0.74 h 0.075 0.095 1.91 2.41 j 0.575 0.625 14.61 15.88 k 0.211 0.219 5.36 5.56 l 0.422 0.437 10.72 11.10 m 0.058 0.068 1.47 1.73 n 0.045 0.055 1.14 1.40 p 0.095 0.115 2.41 2.92 q 0.008 0.016 0.20 0.41 r 0.008 0.016 0.20 0.41 u 0.159 0.163 4.04 4.14 w 0.085 0.095 2.17 2.42
package dimensions data sheets http://www.teccor.com m1 - 6 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog w package ? to-218x non-isolated mounting tab common with center lead j package ? to-218x isolated mounting tab g package ? do-15x axial lead g r y h d c k b a e f n t m p j l s v u dia. w x mt1 / cathode mt2 / anode w package mt2 / anode t c measurement point gate note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). z dim inches millimeters min max min max a 0.810 0.835 20.57 21.21 b 0.610 0.630 15.49 16.00 c 0.178 0.188 4.52 4.78 d 0.055 0.070 1.40 1.78 e 0.487 0.497 12.37 12.62 f 0.635 0.655 16.13 16.64 g 0.022 0.029 0.56 0.74 h 0.075 0.095 1.91 2.41 j 0.575 0.625 14.61 15.88 k 0.256 0.264 6.50 6.71 l 0.220 0.228 5.58 5.79 m 0.080 0.088 2.03 2.24 n 0.169 0.177 4.29 4.49 p 0.034 0.042 0.86 1.07 r 0.113 0.121 2.87 3.07 s 0.086 0.096 2.18 2.44 t 0.156 0.166 3.96 4.22 u 0.159 0.163 4.04 4.14 v 0.603 0.618 15.31 15.70 w 0.000 0.005 0.00 0.13 x 0.003 0.012 0.07 0.30 y 0.028 0.032 0.71 0.81 z 0.085 0.095 2.17 2.42 g l l d b2 t l measuring point dimension inches millimeters min max min max b2 0.027 0.035 0.686 0.889 d 0.104 0.150 2.640 3.810 g 0.230 0.300 5.840 7.620 l 1.000 25.400
data sheets package dimensions ? 2002 teccor electronics m1 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 c package ? compak n package ? to-263 d 2 pak surface mount 0.079 (2.0) 0.040 (1.0) 0.030 (0.76) 0.079 (2.0) 0.079 (2.0) 0.110 (2.8) pad outline h k j e f l g a c b m d n p gate mt1 / cathode mt2 / anode t c / t l temperature measurement point dimensions are in inches (and millimeters). dimension inches millimeters min max min max a 0.140 0.155 3.56 3.94 b 0.205 0.220 5.21 5.59 c 0.077 0.083 1.96 2.11 d 0.166 0.180 4.22 4.57 e 0.036 0.056 0.91 1.42 f 0.073 0.083 1.85 2.11 g 0.004 0.008 0.10 0.20 h 0.077 0.086 1.96 2.18 j 0.043 0.053 1.09 1.35 k 0.008 0.012 0.20 0.30 l 0.027 0.049 0.69 1.24 m 0.022 0.028 1 0.56 0.71 n 0.027 0.033 0.69 0.84 p 0.052 0.058 1.32 1.47 b a v g s d 2pl c e k h j f 0.46 (11.684) 0.17 (4.318) 0.26 (6.604) 0.115 (2.921) 0.15 (3.81) 0.08 (2.032) pad outline 0.085 (2.159) 0.665 (16.891) 0.35 (8.89) u w case temperature measurement dimensions are in inches (and millimeters). mt1 / cathode mt2 / anode gate dimension inches millimeters min max min max a 0.360 0.370 9.14 9.40 b 0.380 0.420 9.65 10.67 c 0.178 0.188 4.52 4.78 d 0.025 0.035 0.63 0.89 e 0.048 0.055 1.22 1.40 f 0.060 0.075 1.52 1.91 g 0.095 0.105 2.41 2.67 h 0.083 0.093 2.11 2.36 j 0.018 0.024 0.46 0.61 k 0.090 0.110 2.29 2.79 s 0.590 0.625 14.99 15.87 v 0.035 0.045 0.89 1.14 u 0.002 0.010 0.05 0.25 w 0.040 0.070 1.02 1.78
package dimensions data sheets http://www.teccor.com m1 - 8 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog d package ? to-252aa d-pak surface mount v package ? to-251aa v-pak through hole g a c b e k p l f .460 0.071 (1.8) 0.118 (3.0) 0.181 (4.6) pad outline 0.264 (6.7) o d case temperature measurement point m h 0.264 (6.7) dimensions are in inches (and millimeters). 0.063 (1.6) mt1 / cathode mt2 / anode gate dimension inches millimeters min max min max a 0.236 0.244 6.00 6.20 b 0.379 0.409 9.63 10.39 c 0.176 0.184 4.47 4.67 d 0.035 0.050 0.89 0.27 e 0.087 0.093 2.21 2.36 f 0.027 0.033 0.69 0.84 g 0.205 0.213 5.21 5.41 h 0.251 0.261 6.38 6.63 j 0.040 0.050 1.02 1.27 k 0.086 0.094 2.18 2.39 l 0.026 0.036 0.66 0.91 m 0.018 0.023 0.46 0.58 n 0.170 0.180 4.32 4.57 o 0.002 0.010 0.05 0.25 p 0.018 0.023 0.46 0.58 d b c j l k a case temperature measurement point h e f g gate mt1 / cathode mt2 / anode mounting ta b internally connected to mt2 mt2 / anode dimension inches millimeters min max min max a 0.040 0.050 1.02 1.27 b 0.236 0.244 6.00 6.20 c 0.350 0.375 8.89 9.53 d 0.205 0.213 5.21 5.41 e 0.251 0.261 6.38 6.63 f 0.027 0.033 0.69 0.84 g 0.087 0.093 2.21 2.36 h 0.086 0.094 2.18 2.39 j 0.018 0.023 0.46 0.58 k 0.036 0.042 0.91 1.07 l 0.018 0.023 0.46 0.58
?2002 teccor electronics m2 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 lead form dimensions m2 the to-202ab, to-220ab, and to-92 package configurations, because of their unique design, can be mounted in a variety of methods, depending upon heat sink requirements and circuit packaging methods. any of the derived types shown in this sec- tion are available as standard parts direct from the factory. cus- tom package variations are available. consult the factory for more information. to designate lead form options, simply indicate the type number at the end of the teccor standard part number. example: q2004f312 (signifies type 12) note: when ordering a to-202 f package, include a 1 for stan- dard full tab package. when ordering anything other than full tab, remove the 1 and add the lead form type. see ?description of part numbers? in the product selection guide of this catalog for a complete description of teccor part numbers. lead bending specifications leads may be bent easily and may be bent to any desired angle, provided that the bend is made at a minimum 0.063" (0.1 for to-218) away from the package body with a minimum radius of 0.032". do-15x device leads may be bent with a minimum radius of 0.050", and do-35 device leads may be bent with a minimum radius of 0.028". leads should be held firmly between the pack- age body and the bend, so that strain on the leads is not trans- mitted to the package body. when bending leads in the plane of the leads (spreading), bend only the narrow part. sharp angle bends should be done only once, as repetitive bend- ing will fatigue and break the leads. m2
http://www.teccor.com m2 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog lead form dimensions data sheets to-202ab type 11 ? f package to-202ab type 12 ? f package to-202ab type 2 ? f package to-202ab type 21 ? f package dimension inches millimeters min max min max a 0.080 0.120 2.03 3.05 b 0.301 0.361 7.65 9.17 c 0.080 0.120 2.03 3.05 dimension inches millimeters min max min max a 0.435 0.495 11.05 12.57 b 0.120 0.160 3.05 4.06 tab common to mt2 / anode mt1 / cathode mt2 / anode gate a b c mt2 / anode tab common to mt2 / anode mt1 / cathode mt2 / anode gate a b dimension inches millimeters min max min max a 0.240 0.260 6.100 6.60 b 0.030 0.050 0.762 1.27 dimension inches millimeters min max min max a 0.030 0.050 0.762 1.27 b 0.240 0.260 6.100 6.60 c 0.080 0.120 2.030 3.05 d 0.301 0.361 7.650 9.17 e 0.080 0.120 2.030 3.05 a mt1 / cathode mt2 / anode gate b mt1 / cathode mt2 / anode gate c d e mt2 / anode a b
?2002 teccor electronics m2 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets lead form dimensions to-202ab type 23 ? f package sidac only to-202ab type 26 ? f package to-202ab type 3 ? f package non-isolated to-202ab type 32 ? f package non-isolated dimension inches millimeters min max min max a 0.240 0.260 6.100 6.60 b 0.030 0.050 0.762 1.27 c 0.030 0.050 0.762 1.27 dimension inches millimeters min max min max a 0.240 0.260 6.100 6.60 b 0.030 0.050 0.762 1.27 c 0.050 0.070 0.127 1.78 d 0.095 0.105 2.410 2.67 e 0.172 0.202 4.370 5.13 mt1 / pin 1 mt2 / pin 2 c a b gate a mt2 / anode mt1 / cathode b e c d dimension inches millimeters min max min max a 0.030 0.050 0.762 1.27 b 0.645 0.705 16.380 17.91 dimension inches millimeters min max min max a 0.030 0.050 0.762 1.27 b 0.435 0.495 11.050 12.57 c 0.120 0.160 3.050 4.06 mt2 / anode mt1 / cathode a b gate mt2 / anode mt1 / cathode gate b c a
http://www.teccor.com m2 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog lead form dimensions data sheets to-202ab type 4 ? f package to-202ab type 41 ? f package to-202ab type 43 ? f package surface mount to-220 type 51 ? r or l package replaces rca 6249 dimension inches millimeters min max min max a 0.240 0.260 6.100 6.600 b 0.114 0.134 2.900 3.400 c 0.023 0.029 0.584 0.737 d 0.030 0.050 0.762 1.270 e 0.297 0.327 7.540 8.310 f 0.030 0.050 0.765 1.270 g 0.297 0.327 7.540 8.310 dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.180 0.220 4.57 5.59 a b c mt2 / anode d e f g gate mt1 / cathode mt2 / anode gate mt1 / cathode b a dimension inches millimeters min max min max a 0.030 0.050 0.762 1.270 b 0.680 0.760 17.270 19.300 c 0.110 0.130 2.800 3.300 d 0.080 0.100 2.030 2.540 e 0.080 0.100 2.030 2.540 f 0.110 0.130 2.800 3.300 g 0.000 0.013 0.000 0.330 dimension inches millimeters min max min max a 0.320 0.340 8.13 8.64 b 0.190 4.83 c 0.795 0.850 20.19 21.59 mt2 / anode a gate mt1 / cathode b f e d c 0.150 0.450 0.150 0.050 five plcs pad outline g a c mt2 / anode gate b ref only mounting tab common to mt2 / anode for non-isolated r package mt1 / cathode
?2002 teccor electronics m2 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets lead form dimensions to-220 type 52 ? r or l package to-220 type 53 ? r or l package to-220 type 54 ? r package replaces motorola form 4, g.e. type 4, rca 6206 to-220 type 55 ? r or l package replaces g.e. type 5 dimension inches millimeters min max min max a 0.169 0.189 4.29 4.80 b 0.040 0.060 1.02 1.52 c 0.250 6.35 d 0.110 0.170 2.79 4.32 dimension inches millimeters min max min max a 0.175 4.45 b 0.542 0.582 13.77 14.78 c 0.167 0.207 4.24 5.26 d 0.355 0.395 9.02 10.03 a c gate / trigger mt2 / anode mt1 / cathode b mounting tab common to mt2 / anode for non-isolated r package d mounting tab common to mt2 / anode for non-isolated r package mt1 / cathode mt2 / anode gate / trigger mt2 / anode a d c b dimension inches millimeters min max min max a 0.040 0.070 1.02 1.78 b 0.500 12.70 dimension inches millimeters min max min max a 0.065 0.095 1.65 2.41 b 0.353 0.433 8.97 11.00 c 0.115 0.130 2.92 3.30 a mt2 / anode gate mt1 / cathode b mounting tab common to mt2 / anode for non-isolated r package mt1 / cathode mt2 / anode gate / trigger c b a mt2 / anode
http://www.teccor.com m2 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog lead form dimensions data sheets to-220 type 56 ? r or l package replaces g.e. type 6, motorola lead form 3, rca 6221 to-220 type 57 ? r package similar to to-66, gate-cathode reversed to-220 type 58 ? r or l package to-220 type 59 ? r or l package dimension inches millimeters min max min max a 0.570 0.590 14.48 14.99 b 0.120 0.130 3.05 3.30 c 0.172 0.202 4.37 5.13 dimension inches millimeters min max min max a 0.040 0.070 1.02 1.78 b 0.570 0.590 14.48 14.99 c 0.340 0.422 8.64 10.72 mounting tab common to mt2 / anode for non-isolated r package mt1 / cathode a c mt2 / anode gate / trigger mt2 / anode b mt1 / cathode c gate mt2 / anode b a dimension inches millimeters min max min max a 0.175 4.45 b 0.542 0.582 13.77 14.78 c 0.167 0.207 4.24 5.26 d 0.355 0.395 9.02 10.03 dimension inches millimeters min max min max a 0.685 0.725 17.40 18.42 b 0.558 0.598 14.17 15.19 c 0.375 9.53 d 0.250 6.35 mounting tab common to mt2 / anode for non-isolated r package mt1 / cathode gate mt2 / anode a d c b mt2 / anode mounting tab common to mt2 / anode for non-isolated r package mt1 / cathode gate d c b mt2 / anode mt2 / anode a
?2002 teccor electronics m2 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets lead form dimensions to-220 type 65 ? r or l package replaces rca 6210 to-220 type 67 ? r package surface mount to-220 type 68 ? r or l package surface mount to-92 type 70 ? e package sidac only dimension inches millimeters min max min max a 0.550 0.580 12.70 14.27 b 0.820 0.260 14.73 15.75 c 0.530 0.570 7.62 d 0.080 0.120 2.03 3.05 dimension inches millimeters min max min max a 0.780 0.850 19.05 21.59 b 0.080 0.100 2.03 2.54 c 0.110 0.130 2.79 3.30 d 0.013 0.33 mt1 / cathode mt2 / anode a b mounting tab common to mt2 / anode for non-isolated r package gate / trigger mt2 / anode c d mt1 / cathode gate b c a d mt2 / anode 0.460 0.270 0.170 0.150 0.050 typ 0.155 0.230 0.115 0.860 pad outline this footprint optional dimension inches millimeters min max min max a 0.780 0.850 19.05 21.59 b 0.080 0.100 2.03 2.54 c 0.110 0.130 2.79 3.30 d 0.013 0.33 dimension inches millimeters min max min max a 0.060 1.52 b 0.50 12.7 mt1 / cathode gate / trigger mt2 / anode b c a d mounting tab common to mt2 / anode for non-isolated r package 0.460 0.270 0.170 .150 0.860 0.050 typ 0.045 0.055 typ 0.230 0.115 pad outline this footprint optional a mt1 / pin 1 b mt2 / pin 3 flat side
http://www.teccor.com m2 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog lead form dimensions data sheets to-92 type 73 ? e package surface mount to-92 type 75 ? e package replaces to-5 pinout to-218 type 81 ? k, m, j, or w packages to-218 type 82 ? m and w packages dimension inches millimeters min max min max a 0.000 0.010 0.000 0.254 b 0.052 0.067 1.320 1.700 c 0.295 0.315 7.490 8.000 dimension inches millimeters min max min max a 0.400 10.16 b 0.500 12.70 c 0.080 0.120 2.03 3.05 d 0.045 0.085 1.14 2.16 e 0.180 0.220 4.57 5.59 f 0.080 0.120 2.03 3.05 a b c mt2 / anode/ pin 3 gate / pin 2 mt1 / cathode / pin 1 0.034 typ 0.016 typ 0.08 pad outline mt2 / anode / pin 3 f b a gate / pin 2 flat side d typ e c mt1 / cathode / pin 1 gate / pin 2 dimension inches millimeters min max min max a 0.080 0.120 2.03 3.05 b 0.580 0.640 14.73 16.26 dimension inches millimeters min max min max a 0.095 2.41 b 0.080 0.120 2.03 3.05 c 0.580 0.640 14.73 16.26 b mt1 / cathode a gate mounting tab common to mt2 / anode on w package mt2 / anode c mt1 / cathode b gate mounting tab common to mt2 / anode a
?2002 teccor electronics m2 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 data sheets lead form dimensions do-35 type 91 ? y package do-35 type 92 ? y package do-35 type 93 ? y package surface mount dimension inches millimeters min max min max a 0.519 0.521 12.18 13.23 b 0.140 0.172 3.56 4.37 dimension inches millimeters min max min max a 0.610 0.630 15.49 16.00 b 0.140 0.172 3.56 4.37 a b a b dimension inches millimeters min max min max a 0.020 0.060 0.508 1.52 b 0.290 0.310 7.370 7.87 c 0.370 0.430 9.400 10.92 d 0.040 0.060 1.020 1.52 b c a d
notes
? 2002 teccor electronics m3 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 packing options m3 packing options include: ?bulk pack ? reel pack (rp) ? ammo pack (ap) ? tube pack (tp) ? embossed carrier (rp) see ?package type and packing options? on page m3-2. sample instructions for choosing a packing option (1) if selecting an ?l401e6? (sensitive gate, 400 v, 1 a triac in a to-92 package), choose one of the options available for that device: ? bulk packed in 2,000 quantity ? tape and reel with 2,000 parts per reel ? tape and ammo with 2,000 parts per box (2) add the designated code as a suffix to the device number, such as ?l401e6 rp? if selecting tape and reel or ?l401e6 ap? if selecting tape and ammo. (bulk packing requires no suffix.) m3
packing options data sheets http://www.teccor.com m3 - 2 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog package type and packing options package type package code packing options bulk pack reel pack (rp) ammo pack (ap) tube pack (tp) embossed carrier (rp) to-92 e 2,000 2,000 2,000 contact factory for availability only type 73 to-220 l, r 500 n/a n/a 50 only type 67 and 68 to-202 f 500 700 (type 2) n/a 50 only type 43 to-218 k, j, m, w 250 n/a n/a contact factory for availability n/a fastpak p 200 n/a n/a n/a n/a to-251 v-pak v 1,000 contact factory for availability n/a 75 n/a to-252 d-pak d n/a n/a n/a 75 2500 to-263 d 2 pak n n/a n/a n/a 50 500 do-214 s 1,000 n/a n/a n/a 2500 compak c 1,000 n/a n/a n/a 2500 do-35 y 10,000 minimum order of 5,000 available 5,000 n/a n/a n/a do-15x g 1,000 5,000 n/a n/a n/a
data sheets packing options ? 2002 teccor electronics m3 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 to-92 (3-lead) reel pack (rp) radial leaded meets all eia-468-b 1994 standards to-92 (3-lead) ammo pack (ap) radial leaded meets all eia-468-b 1994 standards 0.708 (18.0) 1.6 (41.0) 0.5 (12.7) 0.1 (2.54) 0.2 (5.08) 0.236 (6.0) 0.02 (0.5) direction of feed dimensions are in inches (and millimeters). 1.97 (50.0) 14.17(360.0) flat up 1.26 (32.0) 0.098 (2.5) max mt1 / cathode mt2 / anode gate 0.354 (9.0) 0.157 dia (4.0) flat down 25 devices per fold mt1 / cathode mt2 / anode gate direc t ion o f fee d dimensions are in inches (and millimeters). 0.708 (18.0) 1.62 (41.2) 0.5 (12.7) 0.1 (2.54) 0.2 (5.08) 0.236 (6.0) 0.02 (0.5) 1.85 (47.0) 13.3 (338.0) 1.27 (32.2) 0.098 (2.5) max 12.2 (310.0) 1.85 (47.0) 0.354 (9.0) 0.157 dia (4.0)
packing options data sheets http://www.teccor.com m3 - 4 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog to-92 type 70 reel pack (rp3) optional meets all eia-468-b 1994 standards to-92 type 70 reel pack (rp2) standard meets all eia-468-b 1994 standards flat up 0.708 (18.0) 1.3 (33.1) 0.5 (12.7) 0.1 (2.54) 0.354 (9.0) 0.236 (6.0) 0.02 (0.5) direction of feed dimensions are in inches (and millimeters). 1.97 (50.0) 14.17 (360.0) 0.95 (24.1) 0.157 di a (4.0) flat down 1.62 (41.2) 0.708 (18.0) 0.354 (9.0) 0.236 (6.0) 0.02 (0.5) 0.50 (12.7) 14.17 (360.0) 0.20 (5.08) 0.125 (3.2) max 1.27 (32.2) 1.97 (50.0) 0.50 (12.7) 0.25 (6.35) dimensions are in inches (and millimeters). direction of feed 0.157 dia (4.0)
data sheets packing options ? 2002 teccor electronics m3 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 to-92 type 70 ammo pack (ap) radial leaded meets all eia-468-b 1994 standards flat down 25 devices per fold 0.708 (18.0) 1.27 (32.2) 0.125 (3.2) max 1.62 (41.2) max 0.50 (12.7) 0.354 (9.0) 0.236 (6.0) 0.02 (0.5) 0.20 (5.08) 0.50 (12.7) 0.25 (6.35) direction o f fee d dimensions are in inches (and millimeters). 1.85 (47.0) 13.3 (338.0) 12.2 (310.0) 1.85 (47.0) 0.157 dia (4.0)
packing options data sheets http://www.teccor.com m3 - 6 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog to-202 type 2 reel pack (rp) meets all eia-468-b 1994 standards reel pack (rp) for to-252 embossed carrier meets all eia-481-2 standards mt1 / cathode mt2 / anode gate direction of feed dimensions are in inches (and millimeters). 0.708 (18.0) 1.33 (33.8) 0.5 (12.7) 0.1 (2.54) 0.2 (5.08) 0.236 (6.0) 0.02 (0.5) 1.97 (50.0) 14.17 (360.0) 0.63 (16.0) 0.354 (9.0) 0.157 dia (4.0) 0.512 (13.0) arbor hole dia. dc dc xxxxxx dc gate mt1 / cathode mt2 / anode 0.63 (16.0) 0.157 (4.0) 0.64 (16.3) 12.99 (330.0) 0.524 (13.3) 0.315 (8.0) 0.059 dia (1.5) * * cover tape direction of feed dimensions are in inches (and millimeters).
data sheets packing options ? 2002 teccor electronics m3 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 to-263 embossed carrier reel pack (rp) meets all eia-481-2 standards do-214 embossed carrier reel pack (rp) meets all eia-481-1 standards gate mt1 / cathode mt2 / anode 0.512 (13.0) arbor hole dia. 0.945 (24.0) 0.63 (16.0) 1.01 (25.7) 12.99 (330.0) 0.827 (21.0) 0.157 (4.0) direction of feed dimensions are in inches (and millimeters). * * cover tape 0.059 dia (1.5) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 0.157 (4.0) 0.49 (12.4) 0.512 (13.0) arbor hole dia. 12.99 (330.0) dimensions are in inches (and millimeters). direction of feed 0.059 dia (1.5) cover tape
packing options data sheets http://www.teccor.com m3 - 8 ? 2002 teccor electronics +1 972-580-7777 thyristor product catalog compak embossed carrier reel pack (rp) meets all eia-481-1 standards do-15x and do-35 reel pack (rp) meets all eia rs-296 standards 8.0 anode / mt2 cathode / mt1 gate 0.47 (12.0) 0.36 (9.2) 0.315 (8.0) 0.157 (4.0) 0.49 (12.4) 0.512 (13.0) arbor hole dia. 12.99 (330.0) dimensions are in inches (and millimeters). direction of feed 0.059 dia (1.5) cover tape 3.15 (80.0) typ do-15x do-35 dimensions are in inches (and millimeters). direction of feed 0.252 (6.4) 0.898 (22.8) 0.197 (5.0) 2.063 (52.4) 10.0 - 14.0 (254.0 - 356.0) 0.252 (6.4) 0.956 (24.3) 0.197 (5.0) 2.063 (52.4)
?2002 teccor electronics http://www.teccor.com thyristor product catalog +1 972-580-7777 application notes fundamental characteristics of thyristors - - - - - - - - - - - - - - - - - - - an1001 gating, latching, and holding of scrs and triacs - - - - - - - - - - - - - an1002 phase control using thyristors- - - - - - - - - - - - - - - - - - - - - - - - - - - an1003 mounting and handling of semiconductor devices - - - - - - - - - - - - - an1004 surface mount soldering recommendations - - - - - - - - - - - - - - - - - an1005 testing teccor semiconductor devices using curve tracers - - - - - an1006 thyristors used as ac static switches and relays- - - - - - - - - - - - - an1007 explanation of maximum ratings and characteristics for thyristors - an1008 miscellaneous design tips and facts - - - - - - - - - - - - - - - - - - - - - - an1009 thyristors for ignition of fluorescent lamps - - - - - - - - - - - - - - - - - - an1010
notes
?2002 teccor electronics an1001 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 an1001 fundamental characteristics of thyristors introduction the thyristor family of semiconductors consists of several very useful devices. the most widely used of this family are silicon controlled rectifiers (scrs), triacs, sidacs, and diacs. in many applications these devices perform key functions and are real assets in meeting environmental, speed, and reliability specifica- tions which their electro-mechanical counterparts cannot fulfill. this application note presents the basic fundamentals of scr, triac, sidac, and diac thyristors so the user understands how they differ in characteristics and parameters from their electro- mechanical counterparts. also, thyristor terminology is defined. scr basic operation figure an1001.1 shows the simple block construction of an scr. figure an1001.1 scr block construction the operation of a pnpn device can best be visualized as a spe- cially coupled pair of transistors as shown in figure an1001.2. figure an1001.2 coupled pair of transistors as a scr the connections between the two transistors trigger the occur- rence of regenerative action when a proper gate signal is applied to the base of the npn transistor. normal leakage current is so low that the combined h fe of the specially coupled two-transistor feedback amplifier is less than unity, thus keeping the circuit in an off-state condition. a momentary positive pulse applied to the gate biases the npn transistor into conduction which, in turn, biases the pnp transistor into conduction. the effective h fe momentarily becomes greater than unity so that the specially coupled transistors saturate. once saturated, current through the transistors is enough to keep the combined h fe greater than unity. the circuit remains ?on? until it is ?turned off? by reducing the anode-to-cathode current (i t ) so that the combined h fe is less than unity and regeneration ceases. this threshold anode current is the holding current of the scr. geometric construction figure an1001.3 shows cross-sectional views of an scr chip and illustrations of current flow and junction biasing in both the blocking and triggering modes. figure an1001.3 cross-sectional view of scr chip gate gate j1 j2 j3 p n p n schematic symbol block construction cathode anode cathode anode n p n p n p gate cathode j1 j2 j2 j3 anode n n n cathode gate anode load p p two-transistor schematic two-transistor block construction equivalent gate cathode (-) (+) i gt p n n p (+) (+) anode i t forward bias and current flow gate cathode p n n p (-) anode reverse bias reverse biased junction (-) anode equivalent diode relationship forward blocking junction cathode (-) (+) anode equivalent diode relationship cathode (+) reverse biased gate junction an1001
an1001 application notes http://www.teccor.com an1001 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog triac basic operation figure an1001.4 shows the simple block construction of a triac. its primary function is to control power bilaterally in an ac circuit. figure an1001.4 triac block construction operation of a triac can be related to two scrs connected in par- allel in opposite directions as shown in figure an1001.5. although the gates are shown separately for each scr, a triac has a single gate and can be triggered by either polarity. figure an1001.5 scrs connected as a triac since a triac operates in both directions, it behaves essentially the same in either direction as an scr would behave in the for- ward direction (blocking or operating). geometric construction figure an1001.6 show simplified cross-sectional views of a triac chip in various gating quadrants and blocking modes. figure an1001.6 simplified cross-sectional of triac chip n n n p n p block construction main terminal 2 (mt2) gate schematic symbol mt1 gate mt2 main terminal 1 (mt1) mt1 mt2 n n n n n n p p p p gate(+) mt1(-) i gt n n i t mt2(+) quadrant i gate(-) mt1(-) mt2(+) quadrant ii i gt blocking junction mt2(+) mt1(-) equivalent diode relationship n n n n n n n n p p p p gate(+) mt1(+) i gt quadrant iii gate(-) mt1(+) mt2(-) quadrant iv blocking junction equivalent diode relationship i t i t i gt mt1(+) mt2(-) mt2(-)
application notes an1001 ?2002 teccor electronics an1001 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 sidac basic operation the sidac is a multi-layer silicon semiconductor switch. figure an1001.7 illustrates its equivalent block construction using two shockley diodes connected inverse parallel. figure an1001.7 also shows the schematic symbol for the sidac. figure an1001.7 sidac block construction the sidac operates as a bidirectional switch activated by voltage. in the off state, the sidac exhibits leakage currents (i drm ) less than 5 a. as applied voltage exceeds the sidac v bo , the device begins to enter a negative resistance switching mode with char- acteristics similar to an avalanche diode. when supplied with enough current (i s ), the sidac switches to an on state, allowing high current to flow. when it switches to on state, the voltage across the device drops to less than 5 v, depending on magni- tude of the current flow. when the sidac switches on and drops into regeneration, it remains on as long as holding current is less than maximum value (150 ma, typical value of 30 ma to 65 ma). the switching current (i s ) is very near the holding current (i h ) value. when the sidac switches, currents of 10 a to 100 a are easily developed by discharging small capacitor into primary or small, very high-voltage transformers for 10 s to 20 s. the main application for sidacs is ignition circuits or inexpensive high voltage power supplies. geometric construction figure an1001.8 cross-sectional view of a bidirectional sidac chip with multi-layer construction diac basic operation the construction of a diac is similar to an open base npn tran- sistor. figure an1001.9 shows a simple block construction of a diac and its schematic symbol. figure an1001.9 diac block construction the bidirectional transistor-like structure exhibits a high-imped- ance blocking state up to a voltage breakover point (v bo ) above which the device enters a negative-resistance region. these basic diac characteristics produce a bidirectional pulsing oscilla- tor in a resistor-capacitor ac circuit. since the diac is a bidirec- tional device, it makes a good economical trigger for firing triacs in phase control circuits such as light dimmers and motor speed controls. figure an1001.10 shows a simplified ac circuit using a diac and a triac in a phase control application. figure an1001.10 ac phase control circuit geometric construction figure an1001.11 cross-sectional view of diac chip p n p n n p n p 2 3 4 5 2 3 4 1 equivalent diode relationship schematic symbol mt2 mt2 mt1 mt1 p 3 p 1 n 2 n 4 p 5 mt1 mt2 mt1 mt2 n n p mt1 mt2 block construction schematic symbol load n n p mt1 mt2 cross-section of chip equivalent diode relationship mt1 mt2
an1001 application notes http://www.teccor.com an1001 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog electrical characteristic curves of thyristors figure an1001.12 v-i characteristics of scr device figure an1001.13 v-i characteristics of triac device figure an1001.14 v-i characteristics of bilateral trigger diac figure an1001.15 v-i characteristics of a sidac chip methods of switching on thyristors three general methods are available for switching thyristors to on-state condition: ? application of gate signal ? static dv/dt turn-on ? voltage breakover turn-on application of gate signal gate signal must exceed i gt and v gt requirements of the thyristor used. for an scr (unilateral device), this signal must be positive with respect to the cathode polarity. a triac (bilateral device) can be turned on with gate signal of either polarity; however, different polarities have different requirements of i gt and v gt which must be satisfied. since diacs and sidacs do not have a gate, this method of turn-on is not applicable. in fact, the single major application of diacs is to switch on triacs. static dv/dt turn-on static dv/dt turn-on comes from a fast-rising voltage applied across the anode and cathode terminals of an scr or the main terminals of a triac. due to the nature of thyristor construction, a small junction capacitor is formed across each pn junction. figure an1001.16 shows how typical internal capacitors are linked in gated thyristors. figure an1001.16 internal capacitors linked in gated thyristors reverse breakdown voltage forward breakover voltage specified minimum off - state blocking voltage (v drm ) +i -i +v -v minimum holding current (i h ) voltage drop (v t ) at specified current (i t ) latching current (i l ) off - state leakage current - (i drm ) at specified v drm specified minimum reverse blocking voltage (v rrm ) reverse leakage current - (i rrm ) at specified v rrm breakover voltage specified minimum off-state blocking voltage (v drm ) +i -i +v -v minimum holding current (i h ) voltage drop (v t ) at specified current (i t ) latching current (i l ) off-state leakage current ? (i drm ) at specified v drm +i -i 10 ma +v -v breakover current i bo breakover voltage v bo ? v -v +i v drm +v v s i s i h r s i drm i bo v bo v t i t (i s - i bo ) (v bo - v s ) r s = -i
application notes an1001 ?2002 teccor electronics an1001 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 when voltage is impressed suddenly across a pn junction, a charging current flows, equal to: when becomes greater or equal to thyristor i gt , the thyristor switches on. normally, this type of turn-on does not damage the device, providing the surge current is limited. generally, thyristor application circuits are designed with static dv/dt snubber networks if fast-rising voltages are anticipated. voltage breakover turn-on this method is used to switch on sidacs and diacs. however, exceeding voltage breakover of scrs and triacs is definitely not recommended as a turn-on method. in the case of scrs and triacs, leakage current increases until it exceeds the gate current required to turn on these gated thyris- tors in a small localized point. when turn-on occurs by this method, localized heating in a small area may melt the silicon or damage the device if di/dt of the increasing current is not suffi- ciently limited. diacs used in typical phase control circuits are basically pro- tected against excessive current at breakover as long as the fir- ing capacitor is not excessively large. when diacs are used in a zener function, current limiting is necessary. sidacs are typically pulse-firing, high-voltage transformers and are current limited by the transformer primary. the sidac should be operated so peak current amplitude, current duration, and di/dt limits are not exceeded. triac gating modes of operation triacs can be gated in four basic gating modes as shown in figure an1001.17. figure an1001.17 gating modes the most common quadrants for triac gating-on are quadrants i and iii, where the gate supply is synchronized with the main ter- minal supply (gate positive ? mt2 positive, gate negative ? mt2 negative). gate sensitivity of triacs is most optimum in quadrants i and iii due to the inherent thyristor chip construction. if quadrants i and iii cannot be used, the next best operating modes are quadrants ii and iii where the gate has a negative polarity supply with an ac main terminal supply. typically, quad- rant ii is approximately equal in gate sensitivity to quadrant i; however, latching current sensitivity in quadrant ii is lowest. therefore, it is difficult for triacs to latch on in quadrant ii when the main terminal current supply is very low in value. special consideration should be given to gating circuit design when quadrants i and iv are used in actual application, because quadrant iv has the lowest gate sensitivity of all four operating quadrants. general terminology the following definitions of the most widely-used thyristor terms, symbols, and definitions conform to existing eia-jedec stan- dards : breakover point ? any point on the principal voltage-current characteristic for which the differential resistance is zero and where the principal voltage reaches a maximum value principal current ? generic term for the current through the col- lector junction (the current through main terminal 1 and main ter- minal 2 of a triac or anode and cathode of an scr) principal voltage ? voltage between the main terminals: (1) in the case of reverse blocking thyristors, the principal volt- age is called positive when the anode potential is higher than the cathode potential and negative when the anode potential is lower than the cathode potential. (2) for bidirectional thyristors, the principal voltage is called positive when the potential of main terminal 2 is higher than the potential of main terminal 1. off state ? condition of the thyristor corresponding to the high- resistance, low-current portion of the principal voltage-current characteristic between the origin and the breakover point(s) in the switching quadrant(s) on state ? condition of the thyristor corresponding to the low- resistance, low-voltage portion of the principal voltage-current characteristic in the switching quadrant(s). specific terminology average gate power dissipation [p g(av) ] ? value of gate power which may be dissipated between the gate and main terminal 1 (or cathode) averaged over a full cycle breakover current (i bo ) ? principal current at the breakover point breakover voltage (v bo ) ? principal voltage at the breakover point circuit-commutated turn-off time (t q ) ? time interval between the instant when the principal current has decreased to zero after external switching of the principal voltage circuit and the instant when the thyristor is capable of supporting a specified principal voltage without turning on critical rate-of-rise of commutation voltage of a triac (commutating dv/dt) ? minimum value of the rate-of-rise of prin- cipal voltage which will cause switching from the off state to the on state immediately following on-state current conduction in the opposite quadrant ic dv dt ------ = c dv dt ------ mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - note: alternistors will not operate in q iv
an1001 application notes http://www.teccor.com an1001 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog critical rate-of-rise of off-state voltage or static dv/dt (dv/dt) ? minimum value of the rate-of-rise of principal voltage which will cause switching from the off state to the on state critical rate-of-rise of on-state current (di/dt) ? maximum value of the rate-of-rise of on-state current that a thyristor can withstand without harmful effect gate-controlled turn-on time (t gt ) ? time interval between a specified point at the beginning of the gate pulse and the instant when the principal voltage (current) has dropped to a specified low value (or risen to a specified high value) during switching of a thyristor from off state to the on state by a gate pulse. gate trigger current (i gt ) ? minimum gate current required to maintain the thyristor in the on state gate trigger voltage (v gt ) ? gate voltage required to produce the gate trigger current holding current (i h ) ? minimum principal current required to maintain the thyristor in the on state latching current (i l ) ? minimum principal current required to maintain the thyristor in the on state immediately after the switch- ing from off state to on state has occurred and the triggering sig- nal has been removed on-state current (i t ) ? principal current when the thyristor is in the on state on-state voltage (v t ) ? principal voltage when the thyristor is in the on state peak gate power dissipation (p gm ) ? maximum power which may be dissipated between the gate and main terminal 1 (or cathode) for a specified time duration repetitive peak off-state current (i drm ) ? maximum instanta- neous value of the off-state current that results from the applica- tion of repetitive peak off-state voltage repetitive peak off-state voltage (v drm ) ? maximum instanta- neous value of the off-state voltage which occurs across a thyris- tor, including all repetitive transient voltages and excluding all non-repetitive transient voltages repetitive peak reverse current of an scr (i rrm ) ? maximum instantaneous value of the reverse current resulting from the application of repetitive peak reverse voltage repetitive peak reverse voltage of an scr (v rrm ) ? maximum instantaneous value of the reverse voltage which occurs across the thyristor, including all repetitive transient voltages and exclud- ing all non-repetitive transient voltages surge (non-repetitive) on-state current (i tsm ) ? on-state cur- rent of short-time duration and specified waveshape thermal resistance, junction to ambient (r ja ) ? temperature difference between the thyristor junction and ambient divided by the power dissipation causing the temperature difference under conditions of thermal equilibrium note: ambient is the point at which temperature does not change as the result of dissipation. thermal resistance, junction to case (r jc ) ? temperature dif- ference between the thyristor junction and the thyristor case divided by the power dissipation causing the temperature differ- ence under conditions of thermal equilibrium
?2002 teccor electronics an1002 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 an1002 gating, latching, and holding of scrs and triacs introduction gating, latching, and holding currents of thyristors are some of the most important parameters. these parameters and their interrelationship determine whether the scrs and triacs will function properly in various circuit applications. this application note describes how the scr and triac parame- ters are related. this knowledge helps users select best operat- ing modes for various circuit applications. gating of scrs and triacs three general methods are available to switch thyristors to on-state condition: ? applying proper gate signal ? exceeding thyristor static dv/dt characteristics ? exceeding voltage breakover point this application note examines only the application of proper gate signal. gate signal must exceed the i gt and v gt require- ments of the thyristor being used. i gt (gate trigger current) is the minimum gate current required to switch a thyristor from the off state to the on state. v gt (gate trigger voltage) is the voltage required to produce the gate trigger current. scrs (unilateral devices) require a positive gate signal with respect to the cathode polarity. figure an1002.1 shows the cur- rent flow in a cross-sectional view of the scr chip. figure an1002.1 scr current flow in order for the scr to latch on, the anode-to-cathode current (i t ) must exceed the latching current (i l ) requirement. once latched on, the scr remains on until it is turned off when anode-to-cath- ode current drops below holding current (i h ) requirement. triacs (bilateral devices) can be gated on with a gate signal of either polarity with respect to the mt1 terminal; however, differ- ent polarities have different requirements of i gt and v gt . figure an1002.2 illustrates current flow through the triac chip in various gating modes. figure an1002.2 triac current flow (four operating modes) p n n p anode cathode gate (+) (-) (+) i t i gt n n n n n n p p p p gate(+) mt1(-) i gt n n i t mt2(+) quadrant i gate(-) mt1(-) mt2(+) quadrant ii i gt n n n n n n n n p p p p gate(+) mt1(+) i gt quadrant iii gate(-) mt1(+) mt2(-) quadrant iv i t i t i gt mt2(-) an1002
an1002 application notes http://www.teccor.com an1002 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog triacs can be gated on in one of four basic gating modes as shown in figure an1002.3. the most common quadrants for gating on triacs are quadrants i and iii, where the gate supply is synchronized with the main terminal supply (gate positive ? mt2 positive, gate negative ? mt2 negative). optimum triac gate sensitivity is achieved when operating in quadrants i and iii due to the inherent thyristor chip construction. if quadrants i and iii cannot be used, the next best operating modes are quadrants ii and iii where the gate supply has a negative polarity with an ac main terminal supply. typically, quadrant ii is approximately equal in gate sensitivity to quadrant i; however, latching current sensitivity in quadrant ii is lowest. therefore, it is difficult for triacs to latch on in quadrant ii when the main terminal current supply is very low in value. special consideration should be given to gating circuit design when quadrants i and iv are used in actual application, because quadrant iv has the lowest gate sensitivity of all four operating quadrants. figure an1002.3 definition of o perating quadrants in triacs the following table shows the relationships between different gating modes in current required to gate on triacs. example of 4 a triac: if i gt (i) = 10 ma, then i gt (ii) = 16 ma i gt (iii) = 25 ma i gt (iv) = 27 ma gate trigger current is temperature-dependent as shown in figure an1002.4. thyristors become less sensitive with decreasing temperature and more sensitive with increasing temperature. figure an1002.4 typical dc gate trigger current versus case temperature for applications where low temperatures are expected, gate cur- rent supply should be increased to at least two to eight times the gate trigger current requirements at 25 c. the actual factor var- ies by thyristor type and the environmental temperature. example of a 10 a triac: if i gt (i) = 10 ma at 25 c, then i gt (i) = 20 ma at -40 c in applications where high di/dt, high surge, and fast turn-on are expected, gate drive current should be steep rising (1 s rise time) and at least twice rated i gt or higher with minimum 3 s pulse duration. however, if gate drive current magnitude is very high, then duration may have to be limited to keep from over- stressing (exceeding the power dissipation limit of) gate junction. latching current of scrs and triacs latching current (i l ) is the minimum principal current required to maintain the thyristor in the on state immediately after the switch- ing from off state to on state has occurred and the triggering sig- nal has been removed. latching current can best be understood by relating to the ?pick-up? or ?pull-in? level of a mechanical relay. figure an1002.5 and figure an1002.6 illustrate typical thyristor latching phenomenon. in the illustrations in figure an1002.5, the thyristor does not stay on after gate drive is removed due to insufficient available princi- pal current (which is lower than the latching current requirement). figure an1002.5 latching characteristic of thyristor (device not latched) in the illustration in figure an1002.6 the device stays on for the remainder of the half cycle until the principal current falls below the holding current level. figure an1002.5 shows the character- istics of the same device if gate drive is removed or shortened before latching current requirement has been met. typical ratio of at 25 c type operating mode quadrant i quadrant ii quadrant iii quadrant iv 4a triac 1 1.6 2.5 2.7 10 a triac 1 1.5 1.4 3.1 mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - note: alternistors will not operate in q iv i gt in given quadrant () i gt quadrant 1 () ---------------------------------------------------------------------------- - 2.0 1.5 1.0 .5 0 -40 -15 +25 +65 +100 case temperature (t c ) ? ?c ratio of i gt i gt (t c = 25?c) gate pulse (gate drive to thyristor) principal current through thyristor latching current requirement time zero crossing point time
application notes an1002 ?2002 teccor electronics an1002 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1002.6 latching and holding characteristics of thyristor similar to gating, latching current requirements for triacs are dif- ferent for each operating mode (quadrant). definitions of latching modes (quadrants) are the same as gating modes. therefore, definitions shown in figure an1002.2 and figure an1002.3 can be used to describe latching modes (quadrants) as well. the fol- lowing table shows how different latching modes (quadrants) relate to each other. as previously stated, quadrant ii has the lowest latching current sensitivity of all four operating quadrants. example of a 4 amp triac: if i l (i) = 10 ma, then i l (ii) = 40 ma i l (iii) = 12 ma i l (iv) = 11 ma latching current has even somewhat greater temperature depen- dence compared to the dc gate trigger current. applications with low temperature requirements should have sufficient principal current (anode current) available to ensure thyristor latch-on. two key test conditions on latching current specifications are gate drive and available principal (anode) current durations. shortening the gate drive duration can result in higher latching current values. holding current of scrs and triacs holding current (i h ) is the minimum principal current required to maintain the thyristor in the on state. holding current can best be understood by relating it to the ?drop-out? or ?must release? level of a mechanical relay. figure an1002.6 shows the sequences of gate, latching, and holding currents. holding current will always be less than latching. however, the more sensitive the device, the closer the holding current value approaches its latching cur- rent value. holding current is independent of gating and latching, but the device must be fully latched on before a holding current limit can be determined. holding current modes of the thyristor are strictly related to the voltage polarity across the main terminals. the following table illustrates how the positive and negative holding current modes of triacs relate to each other. example of a 10 a triac: if i h (+) = 10 ma, then i h (-) = 13 ma holding current is also temperature-dependent like gating and latching shown in figure an1002.7. the initial on-state current is 200 ma to ensure that the thyristor is fully latched on prior to holding current measurement. again, applications with low tem- perature requirements should have sufficient principal (anode) current available to maintain the thyristor in the on-state condi- tion. both minimum and maximum holding current specifications may be important, depending on application. maximum holding cur- rent must be considered if the thyristor is to stay in conduction at low principal (anode) current; the minimum holding current must be considered if the device is expected to turn off at a low princi- pal (anode) current. figure an1002.7 typical dc holding current vs case temperatures example of a 10 a triac: if i h (+) = 10 ma at 25 c, then i h (+) 7.5 ma at 65 c relationship of gating, latching, and holding currents although gating, latching, and holding currents are independent of each other in some ways, the parameter values are related. if gating is very sensitive, latching and holding will also be very sensitive and vice versa. one way to obtain a sensitive gate and not-so-sensitive latching-holding characteristic is to have an ?amplified gate? as shown in figure an1002.8. typical ratio of at 25 c type operating mode quadrant i quadrant ii quadrant iii quadrant iv 4a triac 1 4 1.2 1.1 10 a triac 141.11 time time holding current poin t zero crossing point principal current through thyristor gate pulse gate drive to thyristor latching current point i l in given quadrant () i l quadrant 1 () ------------------------------------------------------------------------ typical triac holding current ratio type operating mode i h (+) i h (-) 4 a triac 1 1.1 10 a triac 11.3 2.0 1.5 1.0 .5 0 -40 -15 +25 +65 +100 case temperature (t c ) ? ?c ratio of i h i h (t c = 25 ?c) initial on-state current = 200 ma dc
an1002 application notes http://www.teccor.com an1002 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1002.8 ?amplified gate? thyristor circuit the following table and figure an1002.9 show the relationship of gating, latching, and holding of a 4 a device. figure an1002.9 typical gating, latching, and ho lding relationships of 4 a triac at 25 c the relationships of gating, latching, and holding for several device types are shown in the following table. for convenience all ratios are referenced to quadrant i gating. a k a k g g sensitive scr power scr mt2 g g sensitive triac power triac * * resistor is provided for limiting gate current (i gtm ) peaks to power device. * mt2 mt1 mt1 typical 4 a triac gating, latching, and holding relationship parameter quadrants or operating mode quadrant i quadrant ii quadrant iii quadrant iv i gt (ma) 10 17 18 27 i l (ma) 12 48 12 13 i h (ma) 10 10 12 12 50 40 30 20 10 0 10 20 30 40 (ma) 20 10 20 10 quadrant ii quadrant iii (ma) quadrant i quadrant iv i gt (solid line) i l (dotted line) i h (+) i h (?) typical ratio of gating, latching, and holding currents at 25 c devices ratio 4a triac 1.6 2.5 2.7 1.2 4.8 1.2 1.3 1.0 1.2 10 a triac 1.5 1.4 3.1 1.6 4.0 1.8 2.0 1.1 1.6 15 a alternistor 1.5 1.8 ? 2.4 7.0 2.1 ? 2.2 1.9 1 a sensitive scr ???25???25? 6a scr ? ? ? 3.2 ? ? ? 2.6 ? i gt ii () i gt i () ------------------ i gt iii () i gt i () -------------------- i gt iv () i gt i () -------------------- i l i () i gt i () --------------- - i l ii () i gt i () --------------- - i l iii () i gt i () --------------- - i l iv () i gt i () ---------------- i h + () i gt i () --------------- - i h (-) i gt i () --------------- -
application notes an1002 ?2002 teccor electronics an1002 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 examples of a 10 a triac: if i gt (i) = 10 ma, then i gt (ii) = 15 ma i gt (iii) = 14 ma i gt (iv) = 31 ma if i l (i) = 16 ma, then i l (ii) = 40 ma i l (iii) = 18 ma i l (iv) = 20 ma if i h (+) = 11 ma at 25 c, then i h (+) = 16 ma summary gating, latching, and holding current characteristics of thyristors are quite important yet predictable (once a single parameter value is known). their interrelationships (ratios) can also be used to help designers in both initial circuit application design as well as device selection.
notes
?2002 teccor electronics an1003 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 an10039 phase control using thyristors introduction due to high-volume production techniques, thyristors are now priced so that almost any electrical product can benefit from elec- tronic control. a look at the fundamentals of scr and triac phase controls shows how this is possible. output power characteristics phase control is the most common form of thyristor power con- trol. the thyristor is held in the off condition ? that is, all current flow in the circuit is blocked by the thyristor except a minute leak- age current. then the thyristor is triggered into an ?on? condition by the control circuitry. for full-wave ac control, a single triac or two scrs connected in inverse parallel may be used. one of two methods may be used for full-wave dc control ? a bridge rectifier formed by two scrs or an scr placed in series with a diode bridge as shown in figure an1003.1. figure an1003.1 scr/triac connections for various methods of phase control figure an1003.2 illustrates voltage waveform and shows com- mon terms used to describe thyristor operation. delay angle is the time during which the thyristor blocks the line voltage. the conduction angle is the time during which the thyristor is on. it is important to note that the circuit current is determined by the load and power source. for simplification, assume the load is resistive; that is, both the voltage and current waveforms are identical. figure an1003.2 sine wave showing principles of phase control different loads respond to different characteristics of the ac waveform. for example, some are sensitive to average voltage, some to rms voltage, and others to peak voltage. various volt- age characteristics are plotted against conduction angle for half- and full-wave phase control circuits in figure an1003.3 and figure an1003.4. control circuit line load two scr ac control control circuit triac ac control line loa d control circuit one scr dc control control circuit line line load two scr dc control load full-wave rectified operation voltage applied to load delay (triggering) angle conduction angle an1003
an1003 application notes http://www.teccor.com an1003 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1003.3 half-wave p hase control (sinusoidal) figure an1003.4 symmetrical full-wa ve phase control (sinusoidal) figure an1003.3 and figure an1003.4 also show the relative power curve for constant impedance loads such as heaters. because the relative impedance of incandescent lamps and motors change with applied voltage, they do not follow this curve precisely. to use the curves, find the full-wave rated power of the load, and then multiply by the ratio associated with the specific phase angle. thus, a 180 conduction angle in a half-wave circuit provides 0.5 x full-wave conduction power. in a full-wave circuit, a conduction angle of 150 provides 97% full power while a conduction angle of 30 provides only 3% of full power control. therefore, it is usually pointless to obtain conduc- tion angles less than 30 or greater than 150 . figure an1003.5 and figure an1003.6 give convenient direct output voltage readings for 115 v/230 v input voltage. these curves also apply to current in a resistive circuit. figure an1003.5 output voltage of half-wave phase figure an1003.6 output voltage of full-wave phase control peak voltage rms avg power 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 20 40 60 80 100 120 140 160 180 conduction angle ( ) normalized sine wave rms voltage power as fraction of full conduction half wave peak voltage rms 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 20 40 60 80 100 120 140 160 180 conduction angle ( ) normal sine wave rms voltage power as fraction of full conduction full wave power avg peak voltage 180 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 140 160 180 conduction angle ( ) rms avg output voltage 360 320 280 240 200 160 120 80 40 0 input voltage 230 v 115 v half wave peak voltage rms 0 20 40 60 80 100 120 140 160 180 conduction angle ( ) avg output voltage 360 320 280 240 200 160 120 80 40 0 input voltage 230 v 115 v 180 160 140 120 100 80 60 40 20 0 full wave
application notes an1003 ?2002 teccor electronics an1003 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 control characteristics a relaxation oscillator is the simplest and most common control circuit for phase control. figure an1003.7 illustrates this circuit as it would be used with a thyristor. turn-on of the thyristor occurs when the capacitor is charged through the resistor from a voltage or current source until the breakover voltage of the switching device is reached. then, the switching device changes to its on state, and the capacitor is discharged through the thyris- tor gate. trigger devices used are neon bulbs, unijunction tran- sistors, and three-, four-, or five-layer semiconductor trigger devices. phase control of the output waveform is obtained by varying the rc time constant of the charging circuit so the trigger device breakdown occurs at different phase angles within the controlled half or full cycle. figure an1003.7 relaxation oscillator thyristor trigger circuit figure an1003.8 shows the capacitor voltage-time characteristic if the relaxation oscillator is to be operated from a pure dc source. figure an1003.8 capacitor c harging from dc source usually, the design starting point is the selection of a capacitance value which will reliably trigger the thyristor when the capacitance is discharged. trigger devices and thyristor gate triggering char- acteristics play a part in the selection. all the device characteris- tics are not always completely specified in applications, so experimental determination is sometimes needed. upon final selection of the capacitor, the curve shown in figure an1003.8 can be used in determining the charging resistance needed to obtain the desired control characteristics. many circuits begin each half-cycle with the capacitor voltage at or near zero. however, most circuits leave a relatively large residual voltage on the capacitor after discharge. therefore, the charging resistor must be determined on the basis of additional charge necessary to raise the capacitor to trigger potential. for example, assume that we want to trigger an s2010l scr with a 32 v trigger diac. a 0.1 f capacitor will supply the neces- sary scr gate current with the trigger diac. assume a 50 v dc power supply, 30 minimum conduction angle, and 150 maxi- mum conduction angle with a 60 hz input power source. at approximately 32 v, the diac triggers leaving 0.66 v bo of diac voltage on the capacitor. in order for diac to trigger, 22 v must be added to the capacitor potential, and 40 v additional (50-10) are available. the capacitor must be charged to 22/40 or 0.55 of the available charging voltage in the desired time. looking at figure an1003.8, 0.55 of charging voltage represents 0.8 time constant. the 30 conduction angle required that the firing pulse be delayed 150 or 6.92 ms. (the period of 1/2 cycle at 60 hz is 8.33 ms.) to obtain this time delay: 6.92 ms = 0.8 rc rc = 8.68 ms if c = 0.10 f then, to obtain the minimum r (150 conduction angle), the delay is 30 or (30/180) x 8.33 = 1.39 ms 1.39 ms = 0.8 rc rc = 1.74 ms using practical values, a 100 k potentiometer with up to 17 k min- imum (residual) resistance should be used. similar calculations using conduction angles between the maximum and minimum values will give control resistance versus power characteristic of this circuit. triac phase control the basic full-wave triac phase control circuit shown in figure an1003.9 requires only four components. adjustable resistor r 1 and c 1 are a single-element phase-shift network. when the voltage across c 1 reaches breakover voltage (v bo ) of the diac, c 1 is partially discharged by the diac into the triac gate. the triac is then triggered into the conduction mode for the remainder of that half-cycle. in this circuit, triggering is in quad- rants i and iii. the unique simplicity of this circuit makes it suit- able for applications with small control range. switching device voltage or current source triac r c scr 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 012 3 45 6 time constants ratio of ( capacitor voltage supply source voltage ) r 8.68 3 ? 10 0.1 6 ? 10 -------------------------- 86,000 ? == r 1.74 3 ? 10 0.1 6 ? 10 -------------------------- - 17,400 ? ==
an1003 application notes http://www.teccor.com an1003 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1003.9 basic diac-triac phase control the hysteresis (snap back) effect is somewhat similar to the action of a kerosene lantern. that is, when the control knob is first rotated from the off condition, the lamp can be lit only at some intermediate level of brightness, similar to turning up the wick to light the lantern. brightness can then be turned down until it finally reaches the extinguishing point. if this occurs, the lamp can only be relit by turning up the control knob again to the inter- mediate level. figure an1003.10 illustrates the hysteresis effect in capacitor-diac triggering. as r 1 is brought down from its maxi- mum resistance, the voltage across the capacitor increases until the diac first fires at point a, at the end of a half-cycle (conduction angle i ). after the gate pulse, however, the capacitor voltage drops suddenly to about half the triggering voltage, giving the capacitor a different initial condition. the capacitor charges to the diac, triggering voltage at point b in the next half-cycle and giving a steady-state conduction angle shown as for the triac. figure an1003.10 relationship of ac line voltage and triggering voltage in the figure an1003.11 illustration, the addition of a second rc phase-shift network extends the range on control and reduces the hysteresis effect to a negligible region. this circuit will control from 5% to 95% of full load power, but is subject to supply volt- age variations. when r 1 is large, c 1 is charged primarily through r 3 from the phase-shifted voltage appearing across c 2 . this action provides additional range of phase-shift across c 1 and enables c 2 to partially recharge c 1 after the diac has triggered, thus reducing hysteresis. r 3 should be adjusted so that the circuit just drops out of conduction when r 1 is brought to maximum resistance. figure an1003.11 extended range full-wave phase control by using one of the circuits shown in figure an1003.12, the hys- teresis effect can be eliminated entirely. the circuit (a) resets the timing capacitor to the same level after each positive half-cycle, providing a uniform initial condition for the timing capacitor. this circuit is useful only for resistive loads since the firing angle is not symmetrical throughout the range. if symmetrical firing is required, use the circuit (b) shown in figure an1003.12. figure an1003.12 wide-range hysteresis free phase control for more complex control functions, particularly closed loop con- trols, the unijunction transistor may be used for the triggering device in a ramp and pedestal type of firing circuit as shown in figure an1003.13. load r 1 c 1 0.1 f triac (q2010l5) 250 k 3.3 k r 2 120 v (60 hz) (for inductive loads) 100 0.1 f diac ht34b diac triggers at "a" diac does not trigger at "a" b a ac line capacitor voltage i [+diac v bo ] [?diac v bo ] r 4 c 1 diac ht34b triac (q2010l5) 68 k 3.3 k r 1 120 v (60 hz) 0.1 f load r 2 250 k r 3 100 k trim c 2 0.1 f r 3 c 1 diac triac (q2010l5) 15 k 1/2 w 3.3 k r 1 120 v (60 hz) 0.1 f load r 2 250 k d 1 d 2 d 1 , d 2 = 200 v diodes (a) (b) c 1 diac triac (q2010l5) r 3 120 v (60 hz) load d 1 0.1 f r 1 = 250 k pot d 3 r 4 r 1 d 4 r 2 d 2 r 2 , r 3 = 15 k, 1/2 w r 4 = 3.3 k d 1 , d 2 , d 3 , d 4 = 200 v diodes
application notes an1003 ?2002 teccor electronics an1003 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1003.13 precision propor tional temperature control several speed control and light dimming (phase) control circuits have been presented that give details for a complete 120 v appli- cation circuit but none for 240 v. figure an1003.14 and figure an1003.15 show some standard phase control circuits for 240 v, 60 hz/50 hz operation along with 120 v values for comparison. even though there is very little difference, there are a few key things that must be remembered. first, capacitors and triacs con- nected across the 240 v line must be rated at 400 v. secondly, the potentiometer (variable resistor) value must change consider- ably to obtain the proper timing or triggering for 180 in each half- cycle. figure an1003.14 shows a simple single-time-constant light dim- mer (phase control) circuit, giving values for both 120 v and 240 v operation. figure an1003.14 single-time -constant circuit for incandescent light dimming, heat control, and motor speed control the circuit shown in figure an1003.15 is a double-time-constant circuit which has improved performance compared to the circuit shown in figure an1003.14. this circuit uses an additional rc network to extend the phase angle so that the triac can be trig- gered at small conduction angles. the additional rc network also minimizes any hysteresis effect explained and illustrated in figure an1003.10 and figure an1003.11. figure an1003.15 double-time-constant circuit for incandescent light dimming, heat control, and motor speed control load 120 v (60 hz) r 2 r 6 r 7 r 3 r 5 r 4 r 8 d 2 d 1 d 6 d 3 r 1 d 5 temp t t 1 c 1 q 1 d 4 q 2 tria c "gain" 0 ramp time cool hot ujt triggering level pedestal ujt emitter voltage r 1 , r 2 = 2.2 k, 2 w r 3 = 2.2 k, 1/2 w r 4 = thermistor, approx. 5 k at operating temperature r 5 = 10 k potentiometer r 6 = 5 m potentiometer r 7 = 100 k, 1/2 w r 8 = 1 k, 1/2 w q 1 = 2n2646 q 2 = q2010l5 t 1 = dale pt 10-101 or equivalent d 1-4 = 200 v diode d 5 = 20 v zener d 6 = 100 v diode c 1 = 0.1 f, 30 v 0.1 f 200 v 0.1 f 400 v ac input voltage 120 v ac 60 hz 240 v ac 50/60 hz 12 a 3 a 250 k 500 k q2015l9 q4004l4 100 h 200 h r 1 q 1 l 1 c 1 , c 3 r 1 r 2 c 1 ht-32 3.3 k ac input c 2 d 1 q 1 l 1 r 3 * 100 c 3 * load note: l 1 and c 1 form an rfi filter that may be eliminated * dv/dt snubber network when required 0.1 f 100 v ac load current 0.1 f 200 v 0.1 f 400 v 0.1 f 400 v ac input voltage 120 v ac 60 hz 240 v ac 50 hz 240 v ac 60 hz 8 a 6 a 6 a 250 k 500 k 500 k q2010l5 q4008l4 q4008l4 100 h 200 h 200 h r 2 q 1 l 1 c 1 , c 2 , c 4 r 2 r 1 c 1 ht-32 3.3 k ac input c 2 d 1 q 1 l 1 r 4 * 100 c 4 * note: l 1 and c 1 form an rfi filter that may be eliminated * dv/dt snubber network when required r 3 0.1 f 100 v 15 k 1/2 w c 3 load ac load current
an1003 application notes http://www.teccor.com an1003 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog permanent magnet motor control figure an1003.16 illustrates a circuit for phase controlling a per- manent magnet (pm) motor. since pm motors are also genera- tors, they have characteristics that make them difficult for a standard triac to commutate properly. control of a pm motor is easily accomplished by using an alternistor triac with enhanced commutating characteristics. figure an1003.16 circuit for phase controlling a permanent magnet motor pm motors normally require full-wave dc rectification. therefore, the alternistor triac controller should be connected in series with the ac input side of the rectifier bridge. the possible alternative of putting an scr controller in series with the motor on the dc side of the rectifier bridge can be a challenge when it comes to timing and delayed turn-on near the end of the half cycle. the alternistor triac controller shown in figure an1003.16 offers a wide range control so that the alternistror triac can be triggered at a small conduction angle or low motor speed; the rectifiers and alternistors should have similar voltage ratings, with all based on line voltage and actual motor load requirements. scr phase control figure an1003.17 shows a very simple variable resistance half- wave circuit. it provides phase retard from essentially zero (scr full on) to 90 electrical degrees of the anode voltage wave (scr half on). diode cr 1 blocks reverse gate voltage on the negative half-cycle of anode supply voltage. this protects the reverse gate junction of sensitive scrs and keeps power dissipation low for gate resistors on the negative half cycle. the diode is rated to block at least the peak value of the ac supply voltage. the retard angle cannot be extended beyond the 90-degree point because the trigger circuit supply voltage and the trigger voltage produc- ing the gate current to fire are in phase. at the peak of the ac supply voltage, the scr can still be triggered with the maximum value of resistance between anode and gate. since the scr will trigger and latch into conduction the first time i gt is reached, its conduction cannot be delayed beyond 90 electrical degrees with this circuit. figure an1003.17 half-wave control, 0 to 90 conduction figure an1003.18 shows a half-wave phase control circuit using an scr to control a universal motor. this circuit is better than simple resistance firing circuits because the phase-shifting char- acteristics of the rc network permit the firing of the scr beyond the peak of the impressed voltage, resulting in small conduction angles and very slow speed. figure an1003.18 half-wave motor control dc mtr 115 v ac input 1.5 a 3.3 k 250 k 15 k 1/2 w 0.1 f 400 v ht-32 q4006lh4 100 0.1 f 100 v 0.1 f 400 v g mt1 mt2 + - r 1 ac input scr 1 2.2 k r 3 r 2 cr 1 load in4003 in4003 in4004 in4004 in4004 120 v ac 60 hz 120 v ac 60 hz 240 v ac 60 hz 240 v ac 60 hz 240 v ac 50hz 0.8 a 8.5 a 0.8 a 8.5 a 2.5 a 500 k 100 k 1 m 250 k 1 m 1 k not required 1 k not required 1 k ec103b s2010f1 ec103d s4010f1 t106d1 r 2 r 3 scr 1 cr 1 ac input voltage ac load current m r 1 r 2 c 1 d 1 scr 1 ht-32 3.3 k ac supply universal motor cr 1 ac input voltage 120 v ac 60 hz 240 v ac 60 hz 240 v ac 50 hz ac load current 8 a 6.5 a 6.5 a 150 k 200 k 200 k in4003 in4004 in4004 s2015l s4008l s4008l 0.1 f 200 v 0.1 f 400 v 0.1 f 400 v r 2 cr 1 scr 1 c 1
application notes an1003 ?2002 teccor electronics an1003 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 phase control from logic (dc) inputs triacs can also be phase-controlled from pulsed dc unidirec- tional inputs such as those produced by a digital logic control system. therefore, a microprocessor can be interfaced to ac load by using a sensitive gate triac to control a lamp's intensity or a motor's speed. there are two ways to interface the unidirectional logic pulse to control a triac. figure an1003.19 illustrates one easy way if load current is approximately 5 a or less. the sensitive gate triac serves as a direct power switch controlled by htl, ttl, cmos, or integrated circuit operational amplifier. a timed pulse from the system's logic can activate the triac anywhere in the ac sine- wave producing a phase-controlled load. figure an1003.19 sensitive ga te triac operating in quadrants i and iv the key to dc pulse control is correct grounding for dc and ac supply. as shown in figure an1003.19, dc ground and ac ground/neutral must be common plus mt1 must be con- nected to common ground . mt1 of the triac is the return for both main terminal junctions as well as the gate junction. figure an1003.20 shows an example of a unidirectional (all neg- ative) pulse furnished from a special i.c. that is available from lsi computer systems in melville, new york. even though the circuit and load is shown to control a halogen lamp, it could be applied to a common incandescent lamp for touch-controlled dimming. figure an1003.20 typical touch plate halogen lamp dimmer for a circuit to control a heavy-duty inductive load where an alternistor is not compatible or available, two scrs can be driven by an inexpensive to-92 triac to make a very high current triac or alternistor equivalent, as shown in figure an1003.21. see ?rela- tionship of iav, irms, and ipk? in an1009 for design calcula- tions. figure an1003.21 triac driving two inverse parallel non-sensitive gate scrs figure an1003.22 shows another way to interface a unidirec- tional pulse signal and activate ac loads at various points in the ac sine wave. this circuit has an electrically-isolated input which allows load placement to be flexible with respect to ac line. in other words, connection between dc ground and ac neutral is not required. figure an1003.22 opto-isolator driving a triac or alternistor microcontroller phase control traditionally, microcontrollers were too large and expensive to be used in small consumer applications such as a light dimmer. microchip technology inc. of chandler, arizona has developed a line of 8-pin microcontrollers without sacrificing the functionality of their larger counterparts. these devices do not provide high drive outputs, but when combined with a sensitive triac can be used in a cost-effective light dimmer. figure an1003.23 illustrates a simple circuit using a transformer- less power supply, pic 12c508 microcontroller, and a sensitive triac configured to provide a light dimmer control. r 3 is connected to the hot lead of the ac power line and to pin gp 4 . the esd pro- tection diodes of the input structure allow this connection without damage. when the voltage on the ac power line is positive, the protection diode form the input to v dd is forward biased, and the input buffer will see approximately v dd + 0.7 v. the software will read this pin as high. when the voltage on the line is negative, the protection diode from v ss to the input pin is forward biased, and the input buffer sees approximately v ss - 0.7 v. the software will read the pin as low. by polling gp 4 for a change in state, the software can detect zero crossing. load mt 2 sensitive gate triac mt 1 8 16 g v dd ov hot neutral 120 v 60 hz v dd = 15 v dc touch plate 115 v ac 220 v ac halogen lamp n l ls7631 / ls7632 vdd mode cap sync trig vss ext sens 12 3 4 5 6 7 8 mt1 mt2 c 1 c 5 l t g z r 3 c 2 r 1 r 2 c 3 c 4 r 4 r 5 r 6 d 1 + note: as a precaution, transformer should have thermal protection. c 1 = 0.15 f, 200 v c 2 = 0.22 f, 200 v c 3 = 0.02 f, 12 v c 4 = 0.002 f, 12 v c 5 = 100 f, 12 v r 1 = 270, ? w r 2 = 680 k, ? w c 1 = 0.15 f, 400 v c 2 = 0.1 f, 400 v c 3 = 0.02 f, 12 v c 4 = 0.002 f, 12 v c 5 = 100 f, 12 v r 1 = 1 k, ? w r 2 = 1.5 m, ? w r 3 = 62, ? w r 4 = 1 m to 5 m, ? w (selected for sensitivity) r 5 , r 6 = 4.7 m, ? w d 1 = 1n4148 z = 5.6 v, 1 w zener t = q4006lh4 alternistor l = 100 h (rfi filter) r 3 = 62, ? w r 4 = 1 m to 5 m, ? w (selected for sensitivity) r 5 , r 6 = 4.7 m, ? w d 1 = 1n4148 z = 5.6 v, 1 w zener t = q6006lh4 alternistor l = 200 h (rfi filter) 115 v ac 220 v ac or load mt 2 hot neutral a k g a k g mt 1 g triac gate pulse input non-sensitive gate scrs 1 2 6 4 100 100 0.1 f 250 v timed input pulse r in c 1 mt 2 mt 1 hot 120 v 60 hz triac or alternistor neutral load could be here instead of u pp er location g load
an1003 application notes http://www.teccor.com an1003 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1003.23 microcontroller light dimmer control with a zero crossing state detected, software can be written to turn on the triac by going from tri-state to a logic high on the gate and be synchronized with the ac phase cycles (quadrants i and iv). using pull-down switches connected to the microcontol- ler inputs, the user can signal the software to adjust the duty cycle of the triac. for higher amperage loads, a small 0.8 a, to-92 triac (operating in quadrants i and iv) can be used to drive a 25 a alternistor triac (operating in quadrants i and iii) as shown in the heater control illustration in figure an1003.24. for a complete listing of the software used to control this circuit, see the microchip application note picref-4. this application note can be downloaded from microchip's web site at www.microchip.com. 120 v ac (high) ac (return) white rv 1 varistor r 1 47 c 3 0.1 f +5 v r 2 1 m d 1 1n4001 d 1 1n4001 r 3 20 m d 3 1n5231 c 1 220 f c 2 0.01 f v dd gp 5 gp 4 gp 3 v ss gp 0 gp 1 gp 2 r 6 470 q 1 l4008l5 r 4 470 r 5 470 s 2 s 1 bright dim v dd 150 w lamp jp1 remote switch connector 1 2 3 u1 12c508
application notes an1003 ?2002 teccor electronics an1003 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1003.24 microcontroller heater control summary the load currents chosen for the examples in this application note were strictly arbitrary, and the component values will be the same regardless of load current except for the power triac or scr. the voltage rating of the power thyristor devices must be a minimum of 200 v for 120 v input voltage and 400 v for 240 v input voltage. the use of alternistors instead of triacs may be much more acceptable in higher current applications and may eliminate the need for any dv/dt snubber network. for many electrical products in the consumer market, competitive thyristor prices and simplified circuits make automatic control a possibility. these simple circuits give the designer a good feel for the nature of thyristor circuits and their design. more sophistica- tion, such as speed and temperature feedback, can be devel- oped as the control techniques become more familiar. a remarkable phenomenon is the degree of control obtainable with very simple circuits using thyristors. as a result, industrial and consumer products will greatly benefit both in usability and mar- ketability. 120vac (high) ac (return) white rv1 varistor r1 47 c3 .1f +5v r2 1m 2000 w d1 1n4001 d1 1n4001 r3 20m d3 1n5231 c1 220f c2 .01f vdd gp5 gp4 gp3 vss gp0 gp1 gp2 r6 470 r70 100 ? q1 l4x8e5 q2 q4025l6 r4 470 r5 470 s2 s1 increase heat decrease heat vdd u1 12c508
notes
?2002 teccor electronics an1004 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 4 mounting and handling of semiconductor devices introduction proper mounting and handling of semiconductor devices, particu- larly those used in power applications, is an important, yet some- times overlooked, consideration in the assembly of electronic systems. power devices need adequate heat dissipation to increase operating life and reliability and allow the device to operate within manufacturers' specifications. also, in order to avoid damage to the semiconductor chip or internal assembly, the devices should not be abused during assembly. very often, device failures can be attributed directly to a heat sinking or assembly damage problem. the information in this application note guides the semi- conductor user in the proper use of teccor devices, particularly the popular and versatile to-220 and to-202 epoxy packages. contact the teccor applications engineering group for further details or suggestions on use of teccor devices. lead forming ? typical configurations a variety of mounting configurations are possible with teccor power semiconductor to-202, to-92, do-15x, and to-220 packages, depending upon such factors as power requirements, heat sinking, available space, and cost considerations. figure an1004.1 shows typical examples and basic design rules. figure an1004.1 component mounting these are suitable only for vibration-free environments and low- power, free-air applications. for best results, the device should be in a vertical position for maximum heat dissipation from con- vection currents. standard lead forms teccor encourages users to allow factory production of all lead and tab form options. teccor has the automated machinery and expertise to produce pre-formed parts at minimum risk to the device and with greater convenience for the consumer. see the ?lead form dimensions? section of this catalog for a complete list of readily available lead form options. contact teccor for information regarding custom lead form designs. lead bending method leads may be bent easily and to any desired angle, provided that the bend is made at a minimum 0.063" (0.1" for to-218 package) away from the package body with a minimum radius of 0.032" (0.040" for to-218 package) or 1.5 times lead thickness rule. do-15x device leads may be bent with a minimum radius of 0.050?, and do-35 device leads may be bent with a minimum radius of 0.028?. leads should be held firmly between the pack- age body and the bend so that strain on the leads is not transmit- ted to the package body, as shown in figure an1004.2. also, leads should be held firmly when trimming length. a b c d socket type mounting: useful in applications for testing or where frequent removal is necessary. excellent selection of socket products available from com p anies such as molex. an1004
an1004 application notes http://www.teccor.com an1004 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1004.2 lead bending method when bending leads in the plane of the leads (spreading), bend only the narrow part. sharp angle bends should be done only once as repetitive bending will fatigue and break the leads. the mounting tab of the to-202 package may also be bent or formed into any convenient shape as long as it is held firmly between the plastic case and the area to be formed or bent. with- out this precaution, bending the tab may fracture the chip and permanently damage the unit. heat sinking use of the largest, most efficient heat sink as is practical and cost effective extends device life and increases reliability. in the illus- tration shown in figure an1004.3, each device is electrically iso- lated. figure an1004.3 several isolated to-220 devices mounted to a common heat sink many power device failures are a direct result of improper heat dissipation. heat sinks with a mating area smaller than the metal tab of the device are unacceptable. heat sinking material should be at least 0.062" thick to be effective and efficient. note that in all applications the maximum case temperature (t c ) rating of the device must not be exceeded. refer to the individual device data sheet rating curves (t c versus i t ) as well as the indi- vidual device outline drawings for correct t c measurement point. figure an1004.4 through figure an1004.6 show additional examples of acceptable heat sinks. figure an1004.4 examples of pc board mounts figure an1004.5 vertica l mount heat sink several types of vertical mount heat sinks are available. keep heat sink vertical for maximum convection. figure an1004.6 examples of extruded aluminum when coupled with fans, extruded aluminum mounts have the highest efficiency. heat sinking notes care should be taken not to mount heat sinks near other heat- producing elements such as power resistors, because black anodized heat sinks may absorb more heat than they dissipate. some heat sinks can hold several power devices. make sure that if they are in electrical contact to the heat sink, the devices do not short-circuit the desired functions. isolate the devices electrically or move to another location. recall that the mounting tab of tec- cor isolated to-220 devices is electrically isolated so that several devices may be mounted on the same heat sink without extra insulating components. if using an external insulator such as mica, with a thickness of 0.004", an additional thermal resistance of 0.8 c/w for to-220 or 0.5 c/w for to-218 devices is added to the r jc device rating. incorrect (a) (b) correct heat sink heat sin k printed circuit board b a
application notes an1004 ?2002 teccor electronics an1004 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 allow for adequate ventilation. if possible, route heat sinks to out- side of assembly for maximum airflow. mounting surface selection proper mounting surface selection is essential to efficient trans- fer of heat from the semiconductor device to the heat sink and from the heat sink to the ambient. the most popular heat sinks are flat aluminum plates or finned extruded aluminum heat sinks. the mounting surface should be clean and free from burrs or scratches. it should be flat within 0.002 inch per inch, and a sur- face finish of 30 to 60 microinches is acceptable. surfaces with a higher degree of polish do not produce better thermal conductiv- ity. many aluminum heat sinks are black anodized to improve ther- mal emissivity and prevent corrosion. anodizing results in high electrical but negligible thermal insulation. this is an excellent choice for isolated to-220 devices. for applications of to-202 devices where electrical connection to the common anode tab is required, the anodization should be removed. iridite or chromate acid dip finish offers low electrical and thermal resistance. either to-202 or isolated to-220 devices may be mounted directly to this surface, regardless of application. both finishes should be cleaned prior to use to remove manufacturing oils and films. some of the more economical heat sinks are painted black. due to the high thermal resistance of paint, the paint should be removed in the area where the semiconductor is attached. bare aluminum should be buffed with #000 steel wool and fol- lowed with an acetone or alcohol rinse. immediately, thermal grease should be applied to the surface and the device mounted down to prevent dust or metal particles from lodging in the critical interface area. for good thermal contact, the use of thermal grease is essential to fill the air pockets between the semiconductor and the mount- ing surface. this decreases the thermal resistance by 20%. for example, a typical to-220 with r jc of 1.2 c/w may be lowered to 1 c/w by using thermal grease. teccor recommends dow-corning 340 as a proven effective ther- mal grease. fibrous applicators are not recommended as they may tend to leave lint or dust in the interface area. ensure that the grease is spread adequately across the device mounting sur- face, and torque down the device to specification. contact teccor applications engineering for assistance in choos- ing and using the proper heat sink for specific application. hardware and methods to-220 the mounting hole for the teccor to-220 devices should not exceed 0.140? (6/32) clearance. (figure an1004.7) no insulating bushings are needed for the l package (isolated) devices as the tab is electrically isolated from the semiconductor chip. 6/32 mounting hardware, especially round head or fillister machine screws, is recommended and should be torqued to a value of 6 inch-lbs. figure an1004.7 to-220 mounting punched holes are not acceptable due to cratering around the hole which can cause the device to be pulled into the crater by the fastener or can leave a significant portion of the device out of contact with the heat sink. the first effect may cause immediate damage to the package and early failure, while the second can create higher operating temperatures which will shorten operat- ing life. punched holes are quite acceptable in thin metal plates where fine-edge blanking or sheared-through holes are employed. drilled holes must have a properly prepared surface. excessive chamfering is not acceptable as it may create a crater effect. edges must be deburred to promote good contact and avoid puncturing isolation materials. for high-voltage applications, it is recommended that only the metal portion of the to-220 package (as viewed from the bottom of the package) be in contact with the heat sink. this will provide maximum oversurface distance and prevent a high voltage path over the plastic case to a grounded heat sink. to-202 the mounting hole for the teccor to-202 devices should not exceed 0.112? (4/40) clearance. (figure an1004.8) since tab is electrically common with anode, heat sink may or may not need to be electrically isolated from tab. if not, use 4/40 screw with lock washer and nut. mounting torque is 6 inch-lbs. figure an1004.8 to-202 mounting a nylon bushing and mica insulation are required to insulate the tab in an isolated application. a compression washer is recom- mended to avoid damage to the bushing. do not attempt to mount non-formed tabs to a plane surface, as the resulting strain on the case may cause it or the semiconductor chip assembly to fail. teccor has the facilities and expertise to properly tab form to-202 devices for the convenience of the consumer. lockwasher 6-32 nut heatsink * mounting screw 6-32 * screw head must not touch the epoxy body of the device avoid axial stress boundar y of expose d metal tab on heavy aluminum heatsinks high potential appication using isolated to-220 heat sink at case potential a heat sink compression washer nut appropriate screw 4/40 nylon bushing mica insulator tab form b
an1004 application notes http://www.teccor.com an1004 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog to-218 the mounting hole for the to-218 device should not exceed 0.164? (8/32) clearance. isolated versions of to-218 do not require any insulating material since mounting tab is electrically isolated from the semiconductor chip. round lead or fillister machine screws are recommended. maximum torque to be applied to mounting tab should not exceed 8 inch-lbs. the same precautions given for the to-220 package concerning punched holes, drilled holes, and proper prepared heat sink mounting surface apply to the to-218 package. also for high- voltage applications, it is recommended that only the metal por- tion of the mounting surface of the to-218 package be in contact with heat sink. this achieves maximum oversurface distance to prevent a high-voltage path over the device body to grounded heat sink. general mounting notes care must be taken on both packages at all times to avoid strain to the tab or leads. for easy insertion of the part onto the board or heat sink, avoid axial strain on the leads. carefully measure mounting holes for the tab and the leads, and do any forming of the tab or leads before mounting. refer to the ?lead form dimensions? section of this catalog before attempting lead form operations. rivets may be used for less demanding and more economical applications. 1/8" all-aluminum pop rivets can be used on both to-220 and to-202 packages. use a 0.129?-0.133? (#30) drill for the hole and insert the rivet from the top side, as shown in figure an1004.9. an insertion tool, similar to a ?usm? prg 430 hand riveter, is recommended. a wide selection of grip ranges is avail- able, depending upon the thickness of the heat sink material. use an appropriate grip range to securely anchor the device, yet not deform the mounting tab. the recommended rivet tool has a pro- truding nipple that will allow easy insertion of the rivet and keep the tool clear of the plastic case of the device. figure an1004.9 pop riveting technique a milford #511 (milford group, milford, ct) semi-tubular steel rivet set into a 0.129" receiving hole with a riveting machine simi- lar to a milford s256 is also acceptable. contact the rivet machine manufacturer for exact details on application and set-up for optimum results. pneumatic or other impact riveting devices are not recommended due to the shock they may apply to the device. under no circumstance should any tool or hardware come into contact with the case. the case should not be used as a brace for any rotation or shearing force during mounting or in use. non- standard size screws, nuts, and rivets are easily obtainable to avoid clearance problems. always use an accurate torque wrench to mount devices. no gain is achieved by overtorquing devices. in fact, overtorquing may cause the tab and case to deform or rupture, seriously damaging the device. the curve shown in figure an1004.10 illustrates the effect of proper torque. figure an1004.10 effect of torque to sink thermal resistance with proper care, the mounting tab of a device can be soldered to a surface. however, the heat required to accomplish this opera- tion can damage or destroy the semiconductor chip or internal assembly. see ?surface mount soldering recommendations? (an1005) in this catalog. spring-steel clips can be used to replace torqued hardware in assembling thyristors to heat sinks. clips snap into heat sink slots to hold the device in place for pc board insertion. clips are available in several sizes for various heat sink thicknesses and thyristor case styles from aavid thermalloy in concord, new hampshire. a typical heatsink is shown in figure an1004.11 figure an1004.11 typical heat sink using clips 1/2 rated torque rated torque torque ? inch-lbs ? c/watt c-s effect of torque on case to sink thermal resistance
application notes an1004 ?2002 teccor electronics an1004 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 soldering of leads a prime consideration in soldering leads is the soldering of device leads into pc boards, heat sinks, and so on. significant damage can be done to the device through improper soldering. in any soldering process, do not exceed the data sheet lead solder temperature of +230 c for 10 seconds, maximum, 1/16" from the case. this application note presents details about the following three types of soldering: ? hand soldering ? wave soldering ? dip soldering hand soldering this method is mostly used in prototype breadboarding applica- tions and production of small modules. it has the greatest poten- tial for misuse. the following recommendations apply to teccor to-92, to-202, to-220, and to-218 packages. select a small- to medium-duty electric soldering iron of 25 w to 45 w designed for electrical assembly application. tip tempera- ture should be rated from 600 f to 800 f (300 c to 425 c). the iron should have sufficient heat capacity to heat the joint quickly and efficiently in order to minimize contact time to the part. pencil tip probes work very well. neither heavy-duty electri- cal irons of greater than 45 w nor flame-heated irons and large heavy tips are recommended, as the tip temperatures are far too high and uncontrollable and can easily exceed the time-tempera- ture limit of the part. teccor fastpak devices require a different soldering technique. circuit connection can be done by either quick-connect terminals or solder. since most quick-connect 0.250? female terminals have a maxi- mum rating of 30 a, connection to terminals should be made by soldering wires instead of quick-connects. recommended wire is 10 awg stranded wire for use with mt1 and mt2 for load currents above 30 a. soldering should be per- formed with a 100-watt soldering iron. the iron should not remain in contact with the wire and terminal longer than 40 seconds so the fastpak triac is not damaged. for the teccor to-218x package, the basic rules for hand sol- dering apply; however, a larger iron may be required to apply suf- ficient heat to the larger leads to efficiently solder the joint. remember not to exceed the lead solder temperatures of +230 c for 10 seconds, maximum, 1/16" (1.59mm) from the case. a 60/40 or 63/37 sn/pb solder is acceptable. this low melting- point solder, used in conjunction with a mildly activated rosin flux, is recommended. insert the device into the pc board and, if required, attach the device to the heat sink before soldering. each lead should be individually heat sinked as it is soldered. commercially available heat sink clips are excellent for this use. hemostats may also be used if available. needle-nose pliers are a good heat sink choice; however, they are not as handy as stand-alone type clips. in any case, the lead should be clipped or grasped between the solder joint and the case, as near to the joint as possible. avoid straining or twisting the lead in any way. use a clean pre-tinned iron, and solder the joint as quickly as possible. avoid overheating the joint or bringing the iron or solder into contact with other leads that are not heat sinked. wave solder wave soldering is one of the most efficient methods of soldering large numbers of pc boards quickly and effectively. guidelines for soldering by this method are supplied by equipment manufac- turers. the boards should be pre-heated to avoid thermal shock to semiconductor components, and the time-temperature cycle in the solder wave should be regulated to avoid heating the device beyond the recommended temperature rating. a mildly activated resin flux is recommended. figure an1004.12 shows typical heat and time conditions. figure an1004.12 reflow so ldering with pre-heating dip soldering dip soldering is very similar to wave soldering, but it is a hand operation. follow the same considerations as for wave soldering, particularly the time-temperature cycle which may become oper- ator dependent because of the wide process variations that may occur. this method is not recommended. board or device clean-up is left to the discretion of the customer. teccor devices are tolerant of a wide variety of solvents, and they conform to mil-std 202e method 215 ?resistance to solvents.? time (seconds) 0 0 20 40 60 80 100 120 140 160 180 200 220 240 30 60 90 120 150 180 210 240 270 300 temperature ? ?c pre-heat soak reflow cool down 0.5 - 0.6 ? c/s 1.3 - 1.6 ? c/s <2.5 ? c/s <2.5 ? c/s peak temperature 220 ? c - 245 ? c soaking zone reflow zone pre-heating zone ( 2 min. max ) 60 - 90 s typical ( 2-4 min max ) ( 2 min. max ) 30 - 60 s typical 260
notes
?2002 teccor electronics an1005 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 5an1005 surface mount solder ing recommendations introduction the most important consideration in reliability is achieving a good solder bond between surface mount device (smd) and substrate since the solder provides the thermal path from the chip. a good bond is less subject to thermal fatiguing and will result in improved device reliability. the most economic method of soldering is a process in which all different components are soldered simultaneously, such as do-214, compak, to-252 devices, capacitors, and resistors. reflow of soldering the preferred technique for mounting microminiature compo- nents on hybrid thick- and thin-film is reflow soldering. the do-214 is designed to be mounted directly to or on thick-film metallization which has been screened and fired on a substrate. the recommended substrates are alumina or p.c. board mate- rial. recommended metallization is silver palladium or molymanga- nese (plated with nickel or other elements to enhance solderabil- ity). for more information, consult du pont's thick-film handbook or the factory. it is best to prepare the substrate by either dipping it in a solder bath or by screen printing a solder paste. after the substrate is prepared, devices are put in place with vacuum pencils. the device may be laid in place without special alignment procedures since it is self-aligning during the solder reflow process and will be held in place by surface tension. for reliable connections, keep the following in mind: (1) maximum temperature of the leads or tab during the solder- ing cycle does not exceed 275 c. (2) flux must affect neither components nor connectors. (3) residue of the flux must be easy to remove. good flux or solder paste with these properties is available on the market. a recommended flux is alpha 5003 diluted with benzyl alcohol. dilution used will vary with application and must be determined empirically. having first been fluxed, all components are positioned on the substrate. the slight adhesive force of the flux is sufficient to keep the components in place. because solder paste contains a flux, it has good inherent adhe- sive properties which eases positioning of the components. allow flux to dry at room temperature or in a 70 c oven. flux should be dry to the touch. time required will depend on flux used. with the components in position, the substrate is heated to a point where the solder begins to flow. this can be done on a heating plate, on a conveyor belt running through an infrared tun- nel, or by using vapor phase soldering. in the vapor phase soldering process, the entire pc board is uni- formly heated within a vapor phase zone at a temperature of approximately 215 c. the saturated vapor phase zone is obtained by heating an inert (inactive) fluid to the boiling point. the vapor phase is locked in place by a secondary vapor. (figure an1005.1) vapor phase soldering provides uniform heating and prevents overheating. figure an1005.1 principle of vapor phase soldering no matter which method of heating is used, the maximum allowed temperature of the plastic body must not exceed 250 c during the soldering process. for additional information on tem- perature behavior during the soldering process, see figure an1005.2 and figure an1005.3. figure an1005.2 reflow soldering profile transport cooling pipes pc board heating elements boiling liquid (primary medium) vapor phase zone vapor lock (secondary medium) time (seconds) 0 0 20 40 60 80 100 120 140 160 180 200 220 240 30 60 90 120 150 180 210 240 270 300 temperature ? ?c pre-heat soak reflow cool down 0.5 - 0.6 ? c/s 1.3 - 1.6 ? c/s <2.5 ? c/s <2.5 ? c/s peak temperature 220 ? c - 245 ? c soaking zone reflow zone pre-heating zone ( 2 min. max ) 60 - 90 s typical ( 2-4 min max ) ( 2 min. max ) 30 - 60 s typical 260 an1005
an1005 application notes http://www.teccor.com an1005 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog reflow soldering zones zone 1: initial pre-heating stage (25 c to 150 c) ? excess solvent is driven off. ? pcb and components are gradually heated up. ? temperature gradient shall be <2.5 c/sec. zone 2: soak stage (150 c to 180 c) ? flux components start activation and begin to reduce the oxides on component leads and pcb pads. ? pcb components are brought nearer to the temperature at which solder bonding can occur. ? soak allows different mass components to reach the same temperature. ? activated flux keeps metal surfaces from re-oxidizing. zone 3: reflow stage (180 c to 235 c) ? paste is brought to the alloy?s melting point. ? activated flux reduces surface tension at the metal interface so metallurgical bonding occurs. zone 4: cool-down stage (180 c to 25 c) assembly is cooled evenly so thermal shock to the components or pcb is reduced. the surface tension of the liquid solder tends to draw the leads of the device towards the center of the soldering area and so has a correcting effect on slight mispositionings. however, if the layout is not optimized, the same effect can result in undesirable shifts, particularly if the soldering areas on the substrate and the com- ponents are not concentrically arranged. this problem can be solved by using a standard contact pattern which leaves suffi- cient scope for the self-positioning effect (figure an1005.3 and figure an1005.4) figure an1005.5 shows the reflow soldering procedure. figure an1005.3 minimum required di mensions of metal connection of typical do-214 pads on hybrid thick- and thin- film substrates figure an1005.4 modified do-214 comp ak ? three-leaded surface mount package figure an1005.5 reflow soldering procedure after the solder is set and cooled, visually inspect the connec- tions and, where necessary, correct with a soldering iron. finally, the remnants of the flux must be removed carefully. use vapor degrease with an azeotrope solvent or equivalent to remove flux. allow to dry. after the drying procedure is complete, the assembly is ready for testing and/or further processing. 0.079 (2.0) 0.110 (2.8) 0.079 (2.0) pad outlin e dimensions are in inches (and millimeters). 0.079 (2.0) 0.040 (1.0) 0.030 (0.76) 0.079 (2.0) 0.079 (2.0) 0.110 (2.8) pad outline dimensions are in inches (and millimeters). 1. screen print solder paste (or flux) 2. place component (allow flux to dry) 3. reflow solder
application notes an1005 ?2002 teccor electronics an1005 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 wave soldering wave soldering is the most commonly used method for soldering components in pcb assemblies. as with other soldering pro- cesses, a flux is applied before soldering. after the flux is applied, the surface mount devices are glued into place on a pc board. the board is then placed in contact with a molten wave of solder at a temperature between 240 c and 260 c, which affixes the component to the board. dual wave solder baths are also in use. this procedure is the same as mentioned above except a second wave of solder removes excess solder. although wave soldering is the most popular method of pcb assembly, drawbacks exist. the negative features include solder bridging and shadows (pads and leads not completely wetted) as board density increases. also, this method has the sharpest ther- mal gradient. to prevent thermal shock, some sort of pre-heating device must be used. figure an1005.6 shows the procedure for wave soldering pcbs with surface mount devices only. figure an1005.7 shows the procedure for wave soldering pcbs with both surface mount and leaded components. figure an1005.6 wave sol dering pcbs with surface mount devices only figure an1005.7 wave soldering pc bs with both surface mount and leaded components immersion soldering maximum allowed temperature of the soldering bath is 235 c. maximum duration of soldering cycle is five seconds, and forced cooling must be applied. hand soldering it is possible to solder the do-214, compak, and to-252 devices with a miniature hand-held soldering iron, but this method has particular drawbacks and should be restricted to laboratory use and/or incidental repairs on production circuits. recommended metal-alloy (1) 63/37 sn/pb (2) 60/40 sn/pb pre-heating pre-heating is recommended for good soldering and to avoid damage to the do-214, compak, to-252 devices, other compo- nents, and the substrate. maximum pre-heating temperature is 165 c while the maximum pre-heating duration may be 10 sec- onds. however, atmospheric pre-heating is permissible for sev- eral minutes provided temperature does not exceed 125 c. screen print glue wave solder apply glue cure glue place component or pc board insert leaded components turn over the pc board apply glue place smds cure glue turn over the pc board wave solder
an1005 application notes http://www.teccor.com an1005 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog gluing recommendations prior to wave soldering, surface mount devices (smds) must be fixed to the pcb or substrate by means of an appropriate adhe- sive. the adhesive (in most cases a multicomponent adhesive) has to fulfill the following demands: ? uniform viscosity to ensure easy coating ? no chemical reactions upon hardening in order not to deterio- rate component and pc board ? straightforward exchange of components in case of repair low-temperature solder for reducing pc board damage in testing and troubleshooting surface-mounted components, changing parts can be time consuming. moreover, desoldering and soldering cycles can loosen and damage circuit-board pads. use low-temperature solder to minimize damage to the pc board and to quickly remove a component. one low-temperature alloy is indium-tin, in a 50/50 mixture. it melts between 118 c and 125 c, and tin-lead melts at 183 c. if a component needs replacement, holding the board upside down and heating the area with a heat gun will cause the component to fall off. per- forming the operation quickly minimizes damage to the board and component. proper surface preparation is necessary for the in-sn alloy to wet the surface of the copper. the copper must be clean, and you must add flux to allow the alloy to flow freely.you can use rosin dissolved in alcohol. perform the following steps: (1) cut a small piece of solder and flow it onto one of the pads. (2) place the surface-mount component on the pad and melt the soldered pad to its pin while aligning the part. (this operation places all the pins flat onto their pads.) (3) cut small pieces of the alloy solder and flow each piece onto each of the other legs of the component. indium-tin solder is available from aci alloys, san jose, ca and indium corporation of america, utica, ny. multi-use footprint package soldering footprints can be designed to accommodate more than one package. figure an1005.8 shows a footprint design for using both the compak and an sot-223. using the dual pad outline makes it possible to use more than one supplier source. cleaning recommendations using solvents for pc board or substrate cleaning is permitted from approximately 70 c to 80 c. the soldered parts should be cleaned with azeotrope solvent fol- lowed by a solvent such as methol, ethyl, or isopropyl alcohol. ultrasonic cleaning of surface mount components on pcbs or substrates is possible. the following guidelines are recommended when using ultra- sonic cleaning: ? cleaning agent: isopropanol ? bath temperature: approximately 30 c ? duration of cleaning: max 30 seconds ? ultrasonic frequency: 40 khz ? ultrasonic changing pressure: approximately 0.5 bar cleaning of the parts is best accomplished using an ultrasonic cleaner which has approximately 20 w of output per one liter of solvent. replace the solvent on a regular basis. figure an1005.8 dual footprint for compak package mt2 / anode compak footprint footprint for either compak or sot-223 dual pad outline pad outline 0.150 (3.8) 0.328 (8.33) 0.079 (2.0) 0.030 (.76) 0.040 (1.0) 0.019 (.48) 0.079 (2.0) 0.091 (2.31) 0.079 (2.0) .055 (1.4) 0.059 (1.5) typ typ 0.079 (2.0) 0.079 (2.0) 0.079 (2.0) 0.110 (2.8) 0.030 (.76) 0.040 (1.0) gate gate gate mt1 / cathode mt1 not used m t 2 sot-223 footprint dimensions are in inches (and millimeters). mt2 / anode mt1 / cathode mt2 / anode
?2002 teccor electronics an1006 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 6 testing teccor semiconductor devices using curve tracers introduction one of the most useful and versatile instruments for testing semi- conductor devices is the curve tracer (ct). tektronix is the best known manufacturer of curve tracers and produces four basic models: 575, 576, 577 and 370. these instruments are specially adapted crt display screens with associated electronics such as power supplies, amplifiers, and variable input and output func- tions that allow the user to display the operating characteristics of a device in an easy-to-read, standard graph form. operation of tektronix cts is simple and straightforward and easily taught to non-technical personnel. although widely used by semiconductor manufacturers for design and analytical work, the device con- sumer will find many uses for the curve tracer, such as incoming quality control, failure analysis, and supplier comparison. curve tracers may be easily adapted for go-no go production testing. tektronix also supplies optional accessories for specific applica- tions along with other useful hardware. tektronix equipment although tektronix no longer produces curve tracer model 575, many of the units are still operating in the field, and it is still an extremely useful instrument. the 576, 577 and 370 are current curve tracer models and are more streamlined in their appear- ance and operation. the 577 is a less elaborate version of the 576, yet retains all necessary test functions. the following basic functions are common to all curve tracers: ? power supply supplies positive dc voltage, negative dc volt- age, or ac voltage to bias the device. available power is varied by limiting resistors. ? step generator supplies current or voltage in precise steps to control the electrode of the device. the number, polarity, and frequency of steps are selectable. ? horizontal amplifier displays power supply voltage as applied to the device. scale calibration is selectable. ? vertical amplifier displays current drawn from the supply by the device. scale calibration is selectable. curve tracer controls for beam position, calibration, pulse opera- tion, and other functions vary from model to model. the basic theory of operation is that for each curve one terminal is driven with a constant voltage or current and the other one is swept with a half sinewave of voltage. the driving voltage is stepped through several values, and a different trace is drawn on each sweep to generate a family of curves. limitations, accuracy, and correlation although the curve tracer is a highly versatile device, it is not capable of every test that one may wish to perform on semicon- ductor devices such as dv/dt, secondary reverse breakdown, switching speeds, and others. also, tests at very high currents and/or voltages are difficult to conduct accurately and without damaging the devices. a special high-current test fixture avail- able from tektronix can extend operation to 200 a pulsed peak. kelvin contacts available on the 576 and 577 eliminate inaccu- racy in voltage measured at high current (v tm ) by sensing voltage drop due to contact resistance and subtracting from the reading. accuracy of the unit is within the published manufacturer?s speci- fication. allow the curve tracer to warm up and stabilize before testing begins. always expand the horizontal or vertical scale as far as possible to increase the resolution. be judicious in record- ing data from the screen, as the trace line width and scale resolu- tion factor somewhat limit the accuracy of what may be read. regular calibration checks of the instrument are recommended. some users keep a selection of calibrated devices on hand to verify instrument operation when in doubt. re-calibration or adjustment should be performed only by qualified personnel. often discrepancies exist between measurements taken on different types of instrument. in particular, most semiconductor manufacturers use high-speed, computerized test equipment to test devices. they test using very short pulses. if a borderline unit is then measured on a curve tracer, it may appear to be out of specification. the most common culprit here is heat. when a semiconductor device increases in temperature due to current flow, certain characteristics may change, notably gate character- istics on scrs, gain on transistors, leakage, and so on. it is very difficult to operate the curve tracer in such a way as to eliminate the heating effect. pulsed or single-trace operation helps reduce this problem, but care should be taken in comparing curve tracer measurements to computer tests. other factors such as stray capacitances, impedance matching, noise, and device oscillation also may create differences. an1006
an1006 application notes http://www.teccor.com an1006 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog safety (cautions and warnings) adhere rigidly to tektronix safety rules supplied with each curve tracer. no attempt should be made to defeat any of the safety interlocks on the device as the curve tracer can produce a lethal shock. also, older 575 models do not have the safety inter- locks as do the new models. take care never to touch any device or open the terminal while energized. warning: devices on the curve tracer may be easily dam- aged from electrical overstress. follow these rules to avoid destroying devices: ? familiarize yourself with the expected maximum limits of the device. ? limit the current with the variable resistor to the minimum nec- essary to conduct the test. ? increase power slowly to the specified limit. ? watch for device ?runaway? due to heating. ? apply and increase gate or base drive slowly and in small steps. ? conduct tests in the minimum time required. general test procedures read all manuals before operating a curve tracer. perform the following manufacturer?s equipment check: 1. turn on and warm up curve tracer, but turn off, or down, all power supplies. 2. correctly identify terminals of the device to be tested. refer to the manufacturer?s guide if necessary. 3. insert the device into the test fixture, matching the device and test terminals. 4. remove hands from the device and/or close interlock cover. 5. apply required bias and/or drive. 6. record results as required. 7. disconnect all power to the device before removing. model 576 curve tracer procedures the following test procedures are written for use with the model 576 curve tracer. (figure an1006.1) see ?model 370 curve tracer procedure notes? on page an1006-16 and ?model 577 curve tracer procedure notes? on page an1006-18 for setting adjustments required when using model 370 and 577 curve tracers. the standard 575 model lacks ac mode, voltage greater than 200 v, pulse operations, dc mode, and step offset controls. the 575 mod122c does allow voltage up to 400 v, including 1500 v in an ac mode. remember that at the time of design, the 575 was built to test only transistors and diodes. some ingenuity, experience, and external hardware may be required to test other types of devices. for further information or assistance in device testing on tek- tronix curve tracers, contact the teccor applications engineering group.
application notes an1006 ?2002 teccor electronics an1006 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1006.1 tektronix model 576 curve tracer per v e r t div per h o r i z div per s t e p ()k div 9m per div type 576 tektronix, inc. curve tracer portland, ore, u.s.a. vertical display offset horizontal step generator amplitude collector supply horizontal voltage control note: all voltage settings will be referenced to "collector" step/offset amplitude (amps/volts) offset step/offset polarity rate terminal selector kelvin terminals used when measuring v tm or v fm variable collector supply voltage variable collector supply voltage range crt terminal jacks c b e gate/trigger left-right selector for terminal jacks max peak power (power dissipation) mt2/anode mt1/cathode step family c b e
an1006 application notes http://www.teccor.com an1006 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog power rectifiers the rectifier is a unidirectional device which conducts when for- ward voltage (above 0.7 v) is applied. to connect the rectifier: 1. connect anode to collector terminal (c) . 2. connect cathode to emitter terminal (e) . to begin testing, perform the following procedures. procedure 1: v rrm and i rm to measure the v rrm and i rm parameter: 1. set variable collector supply voltage range to 1500 v. ( 2000 v on 370) 2. set horizontal knob to sufficient scale to allow viewing of trace at the required voltage level ( 100 v/div for 400 v and 600 v devices and 50 v/div for 200 v devices). 3. set mode to leakage. 4. set vertical knob to 100 a/div. (due to leakage setting, the crt readou t will be 100 na per division.) 5. set terminal selector to emitter grounded-open base. 6. set polarity to (?). 7. set power dissipation to 2.2 w. ( 2w on 370) 8. set left-right terminal jack selector to correspond with location of test fixture. 9. increase variable collector supply voltage to the rated v rrm of the device and observe the dot on the crt. read across horizontally from the dot to the vertical current scale. this measured value is the leakage current. (figure an1006.2) figure an1006.2 i rm = 340 na at v rrm = 600 v procedure 2: v fm before testing, note the following: ? a kelvin test fixture is required for this test. if a kelvin fixture is not used, an error in measurement of vfm will result due to voltage drop in fixture. if a kelvin fixture is not available, figure an1006.3 shows necessary information to wire a test fixture with kelvin connections. ? due to the current limitations of standard curve tracer model 576, v fm cannot be tested at rated current without a tek- tronix model 176 high-current module. the procedure below is done at i t(rms) = 10 a (20 a pk ). this test parameter allows the use of a standard curve tracer and still provides an estimate of whether v fm is within specification. figure an1006.3 instructions for wiring kelvin socket to measure the v fm parameter: 1. set variable collector supply voltage range to 15 max peak volts . ( 16 v on 370) 2. set horizontal knob to 0.5 v/div . 3. set mode to norm . 4. set vertical knob to 2 a/div . 5. set power dissipation to 220 w ( 100 w on 577). 6. set polarity to (+). 7. set left-right terminal jack selector to correspond with location of test fixture. 8. increase variable collector supply voltage until current reaches 20 a. warning: limit test time to 15 seconds maximum. to measure v fm , follow along horizontal scale to the point where the trace crosses the 20 a axis. the distance from the left-hand side of scale to the crossing point is the v fm value. (figure an1006.4) note: model 370 current is limited to 10 a. v rrm i rm 100 na 100 v per v e r t div per h o r i z div per s t e p ()k div 9m per div socket socket pins one set of pins wired to collector (c), base (b), and emitter (e) terminals the pins which correspond to the anode and cathode of the device are wired to the terminals marked c sense (mt2/anode) and e sense (mt1/cathode). the gate does not require a kelvin connection. socket used must have two sets of pins
application notes an1006 ?2002 teccor electronics an1006 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1006.4 v fm = 1 v at i pk = 20 a scrs scrs are half-wave unidirectional rectifiers turned on when cur- rent is supplied to the gate terminal. if the current supplied to the gate is to be in the range of 12 a and 500 a, then a sensitive scr is required; if the gate current is between 1 ma and 50 ma, then a non-sensitive scr is required. to connect the rectifier: 1. connect anode to collector terminal (c) . 2. connect cathode to emitter terminal (e) . note: when sensitive scrs are being tested, a 1 k ? resistor must be connected between the gate and the cathode, except when testing i gt . to begin testing, perform the following procedures. procedure 1: v drm , v rrm , i drm , i rrm to measure the v drm , v rrm , i drm , and i rrm parameter: 1. set variable collector supply voltage range to appropri- ate max peak volts for device under test. (value selected should be equal to or greater than the device?s v drm rating.) 2. set horizontal knob to sufficient scale to allow viewing of trace at the required voltage level. (the 100 v/div scale should be used for testing devices having a v drm value of 600 v or greater; the 50 v/div scale for testing parts rated from 300 v to 500 v, and so on.) 3. set mode to leakage . 4. set polarity to (+). 5. set power dissipation to 0.5 w. ( 0.4 w on 370) 6. set terminal selector to emitter grounded-open base . 7. set vertical knob to approximately ten times the maximum leakage current (i drm , i rrm ) specified for the device. (for sensitive scrs, set to 50 a .) note: the crt screen readout should show 1% of the maximum leakage current if the vertical scale is divided by 1,000 when leakage current mode is used. procedure 2: v drm , i drm to measure the v drm and i drm parameter: 1. set left-right terminal jack selector to correspond with location of test fixture. 2. set variable collector supply voltage to the rated v drm of the device and observe the dot on crt. read across hori- zontally from the dot to the vertical current scale. this mea- sured value is the leakage current. (figure an1006.5) warning: do not exceed v drm /v rrm rating of scrs, triacs, or quadracs . these devices can be damaged. figure an1006.5 i drm = 350 na at v drm = 600 v procedure 3: v rrm , i rrm to measure the v rrm and i rrm parameter: 1. set polarity to (?). 2. repeat steps 1 and 2 (v drm , i drm ) except substitute v rrm value for v drm . (figure an1006.6) . figure an1006.6 i rrm = 340 na at v rrm = 600 v procedure 4: v tm to measure the v tm parameter: 1. set terminal selector to step generator-emitter grounded . 2. set polarity to (+) . 3. set step/offset amplitude to twice the maximum i gt rating of the device (to ensure the device turns on). for sensitive scrs, set to 2ma . 4. set max peak volts to 15 v . ( 16 v on 370) 5. set offset by depressing 0 (zero). 500 mv per v e r t div per h o r i z div per s t e p i t v fm 2 a ()k div 9m per div 100 na 100 v per v e r t div per h o r i z div per s t e p v drm i drm ()k div 9m per div 100 na 100 v per v e r t div per h o r i z div per s t e p v rrm i rrm ()k div 9m per div
an1006 application notes http://www.teccor.com an1006 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog 6. set rate by depressing norm . 7. set step family by depressing rep (repetitive). 8. set mode to dc . 9. set horizontal knob to 0.5 v/div . 10. set power dissipation to 220 w ( 100 w on 577). 11. set number of steps to 1 . (set steps to 0 (zero) on 370.) 12. set vertical knob to a sufficient setting to allow the viewing of 2 times the i t(rms) rating of the device (i t(peak) ) on crt. before continuing with testing, note the following: (1) due to the excessive amount of power that can be generated in this test, only parts with an i t(rms) rating of 6 a or less should be tested on standard curve tracer. if testing devices above 6 a, a tektronix model 176 high-current module is required. (2) a kelvin test fixture is required for this test. if a kelvin fixture is not used, an error in measurement of v tm will result due to voltage drop in the fixture. if a kelvin fixture is not available, figure an1006.3 shows necessary information to wire a test fixture with kelvin connectors. 13. set left-right terminal jack selector to correspond with the location of the test fixture. 14. increase variable collector supply voltage until current reaches rated i t(peak) , which is twice the i t(rms) rating of the- scr under test. note: model 370 current is limited to 10 a. warning: limit test time to 15 seconds maximum after the variable collector supply has been set to i t(peak) , after the variable collector supply voltage has been set to i t(peak) , the test time can automatically be shortened by changing step family from repetitive to single by depressing the single button. to measure v tm , follow along horizontal scale to the point where the trace crosses the i t(peak) value. the distance from the left- hand side of scale to the intersection point is the v tm value. (figure an1006.7) figure an1006.7 v tm = 1.15 v at i t(peak) = 12 a procedure 5: i h to measure the i h parameter: 1. set polarity to (+) . 2. set power dissipation to 2.2 w . ( 2w on 370) 3. set max peak volts to 75 v . (80 v on 370) 4. set mode to dc . 5. set horizontal knob to step generator . 6. set vertical knob to approximately 10 percent of the maxi- mum i h specified. note: due to large variation of holding current values, the scale may have to be adjusted to observe holding current. 7. set number of steps to 1 . 8. set offset by depressing 0 (zero). (press aid and oppose at the same time on 370.) 9. set step/offset amplitude to twice the maximum i gt of the device. 10. set terminal selector to step generator-emitter grounded. 11. set step family by depressing single . 12. set left-right terminal jack selector to correspond with location of test fixture. 13. increase variable collector supply voltage to maximum position ( 100 ). 14. set step family by depressing single. (this could possibly cause the dot on crt to disappear, depending on the verti- cal scale selected.) 15. change terminal selector from step generator-emitter grounded to open base-emitter grounded . 16. decrease variable collector supply voltage to the point where the line on the crt changes to a dot. the position of the beginning point of the line, just before the line becomes a dot, represents the holding current value. (figure an1006.8) figure an1006.8 i h = 1.2 ma procedure 6: i gt and v gt to measure the i gt and v gt parameter: 1. set polarity to (+). 2. set number of steps to 1 . 3. set offset by depressing aid . 4. set offset multiplier to 0 (zero). (press aid and oppose at the same time on 370.) 5. set terminal selector to step generator-emitter grounded. 6. set mode to norm . 7. set max peak volts to 15 v . ( 16 v on 370) 500 mv per v e r t div per h o r i z div per s t e p i pk v tm 2 a ()k div 9m per div 100 ma 20 500 a per v e r t div per h o r i z div per s t e p i h ()k div 9m per div
application notes an1006 ?2002 teccor electronics an1006 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 8. set power dissipation to 2.2 w. ( 2w on 370) for sensitive scrs, set at 0.5 w. ( 0.4 w on 370) 9. set horizontal knob to 2 v/div . 10. set vertical knob to 50 ma/div . 11. increase variable collector supply voltage until voltage reaches 12 v on crt. 12. after 12 v setting is completed, change horizontal knob to step generator . procedure 7: i gt to measure the i gt parameter: 1. set step/offset amplitude to 20% of maximum rated i gt . note: r gk should be removed when testing i gt . 2. set left-right terminal jack selector to correspond with location of the test fixture. 3. gradually increase offset multiplier until device reaches the conduction point. (figure an1006.9) measure i gt by fol- lowing horizontal axis to the point where the vertical line crosses axis. this measured value is i gt . (on 370, i gt will be numerically displayed on screen under offset value.) figure an1006.9 i gt = 25 a procedure 8: v gt to measure the v gt parameter: 1. set offset multiplier to 0 (zero). (press aid and o ppose at the same time on 370.) 2. set step offset amplitude to 20% rated v gt . 3. set left-right terminal jack selector to correspond with location of test fixture. 4. gradually increase offset multiplier until device reaches the conduction point. (figure an1006.10) measure v gt by following horizontal axis to the point where the vertical line crosses axis. this measured value is v gt . (on 370, v gt will be numerically displayed on screen, under offset value.) procedure 9: gt will be numerically displayed on screen under offset value.) figure an1006.10 v gt = 580 mv triacs triacs are full-wave bidirectional ac switches turned on when current is supplied to the gate terminal of the device. if gate con- trol in all four quadrants is required, then a sensitive gate triac is needed, whereas a standard triac can be used if gate control is only required in quadrants i through iii. to connect the triac: 1. connect the gate to the base terminal (b). 2. connect mt1 to the emitter terminal (e). 3. connect mt2 to the collector terminal (c). to begin testing, perform the following procedures. procedure 1: (+)v drm , (+)i drm , (-)v drm , (-)i drm note: the (+) and (-) symbols are used to designate the polarity mt2 with reference to mt1. to measure the (+)v drm , (+)i drm , (-)v drm , and (-)i drm parameter: 1. set variable collector supply voltage range to appropri- ate max peak volts for device under test. (value selected should be equal to the device?s v drm rating.) warning: do not exceed v drm /v rrm rating of scrs, tri- acs, or quadracs . these devices can be damaged. 2. set horizontal knob to sufficient scale to allow viewing of trace at the required voltage level. (the 100 v/div scale should be used for testing devices having a v drm rating of 600 v or greater; the 50 v/div scale for testing parts rated from 30 v to 500 v, and so on.) 3. set mode to leakage . 4. set polarity to (+). 5. set power dissipation to 0.5 w . ( 0.4 w on 370) 6. set terminal selector to emitter grounded-open base . 7. set vertical knob to ten times the maximum leakage current (i drm ) specified for the device. note: the crt screen readout should show 1% of the maxi- mum leakage current. the vertical scale is divided by 1,000 when leakage mode is used. 50 ma per v e r t div per h o r i z div per s t e p i gt ()k div 9m per div 10 a 5 k 50 ma per v e r t div per h o r i z div per s t e p v gt 200 mv 250m ()k div 9m per div
an1006 application notes http://www.teccor.com an1006 - 8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog procedure 2: (+)v drm , (+)i drm to measure the (+)v drm and (+)i drm parameter: 1. set left-right terminal jack selector to correspond with location of the test fixture. 2. increase variable collector supply voltage to the rated v drm of the device and observe the dot on the crt. read across horizontally from the dot to the vertical current scale. this measured value is the leakage current. (figure an1006.11) figure an1006.11 (+)i drm = 205 na at (+)v drm = 600 v procedure 3: (-)v drm , (-)i drm to measure the (-)v drm and (-)i drm parameter: 1. set polarity to (?). 2. repeat procedures 1 and 2. (read measurements from upper right corner of the screen.) procedure 4: v tm (forward and reverse) to measure the v tm (forward and reverse) parameter: 1. set terminal selector to step generator-emitter grounded . 2. set step/offset amplitude to twice the maximum i gt rating of the device (to insure the device turns on). 3. set variable collector supply voltage range to 15 v max peak volts . ( 16 v on 370) 4. set offset by depressing 0 (zero) . 5. set rate by depressing norm. 6. set step family by depressing rep (repetitive). 7. set mode to norm . 8. set horizontal knob to 0.5 v/div . 9. set power dissipation to 220 w ( 100 w on 577). 10. set number of steps to 1 . 11. set step/offset polarity to non-inverted (button extended; on 577 button depressed). 12. set vertical knob to a sufficient setting to allow the viewing of 1.4 times the i t(rms) rating of the device [i t(peak) on crt]. note the following: ? due to the excessive amount of power that can be generated in this test, only parts with an i t(rms) rating of 8 a or less should be tested on standard curve tracer. if testing devices above 8 a, a tektronix model 176 high-current module is required. ? a kelvin test fixture is required for this test. if a kelvin fixture is not used, an error in measurement of v tm will result due to volt- age drop in fixture. if a kelvin fixture is not available, figure an1006.3 shows necessary information to wire a test fixture with kelvin connections. procedure 5: v tm (forward) to measure the v tm (forward) parameter: 1. set polarity to (+). 2. set left-right terminal jack selector to correspond with location of test fixture. 3. increase variable collector supply voltage until current reaches rated i t(peak) , which is 1.4 times i t(rms) rating of the triac under test. note: model 370 current is limited to 10 a. warning: limit test time to 15 seconds maximum. after the variable collector supply voltage has been set to i t(peak) , the test time can automatically be set to a short test time by changing step family from repetitive to single by depress- ing the single button. to measure v tm , follow along horizontal scale to the point where the trace crosses the i t(peak) value. the distance from the left- hand side of scale to the crossing point is the v tm value. (figure an1006.12) figure an1006.12 v tm (forward) = 1.1 v at i pk = 11.3 a (8 a rms) procedure 6: v tm (reverse) to measure the v tm (reverse) parameter: 1. set polarity to (?). 2. set left-right terminal jack selector to correspond with the location of the test fixture. 3. increase variable collector supply voltage until current reaches rated i t(peak) . 4. measure v tm(reverse) similar to figure an1006.12, except from upper right hand corner of screen. procedure 7: i h(forward and reverse) to measure the i h (forward and reverse) parameter: 1. set step/offset amplitude to twice the i gt rating of the device. 2. set power dissipation to 10 w . 50 na 100 v per v e r t div per h o r i z div per s t e p i drm v drm ()k div 9m per div 500 mv per v e r t div per h o r i z div per s t e p v tm i pk 2 a 100 ma 20 ()k div 9m per div
application notes an1006 ?2002 teccor electronics an1006 - 9 http://www.teccor.com thyristor product catalog +1 972-580-7777 3. set max peak volts to 75 v . ( 80 v on 370) 4. set mode to dc . 5. set horizontal knob to step generator . 6. set vertical knob to approximately 10% of the maximum i h specified. note: due to large variation of holding current values, the scale may have to be adjusted to observe holding current. 7. set number of steps to 1 . 8. set step/offset polarity to non-inverted (button extended, on 577 button depressed). 9. set offset by depressing 0 (zero). (press aid and o ppose at same time on 370.) 10. set terminal selector to step generator-emitter grounded. procedure 8: i h(forward) to measure the i h (forward) parameter: 1. set polarity to (+). 2. set left-right terminal jack selector to correspond with location of test fixture. 3. increase variable collector supply voltage to maximum position ( 100 ). 4. set step family by depressing single. this could possibly cause the dot on the crt to disappear, depending on the vertical scale selected). 5. decrease variable collector supply voltage to the point where the line on the crt changes to a dot. the position of the beginning point of the line, just before the line becomes a dot, represents the holding current value. (figure an1006.13) figure an1006.13 i h (forward) = 8.2 ma procedure 9: i h(reverse) to measure the i h (reverse) parameter: 1. set polarity to (?). 2. repeat procedure 7 measuring i h(reverse) . (read measure- ments from upper right corner of the screen.) procedure 10: i gt to measure the i gt parameter: 1. set polarity to (+). 2. set number of steps to 1 . (set number of steps to 0 (zero) on 370.) 3. set offset by depressing aid . (on 577, also set zero button to offset . button is extended.) 4. set offset multiplier to 0 (zero). (press aid and oppose at same time on 370.) 5. set terminal selector to step generator-emitter grounded. 6. set mode to norm. 7. set max peak volts to 15 v . ( 16 v on 370) 8. set power dissipation to 10 w . 9. set step family by depressing single . 10. set horizontal knob to 2 v/div . 11. set vertical knob to 50 ma/div . 12. set step/offset polarity to non-inverted position (button extended, on 577 button depressed). 13. set variable collector supply voltage until voltage reaches 12 v on crt. 14. after 12 v setting is completed, change horizontal knob to step generator . procedure 11: i gt ? quadrant i [mt2 (+) gate (+)] to measure the i gt ? quadrant i parameter: 1. set step/offset amplitude to approximately 10% of rated i gt . 2. set left-right terminal jack selector to correspond with location of test fixture. 3. gradually increase offset multiplier until device reaches conduction point. (figure an1006.14) measure i gt by follow- ing horizontal axis to the point where the vertical line passes through the axis. this measured value is i gt . (on 370, i gt is numerically displayed on screen under offset value.) figure an1006.14 i gt in quadrant i = 18.8 ma 5 ma 100m per v e r t div per h o r i z div per s t e p ()k div 9m per div 50 ma i h 50 ma 10 per v e r t div per h o r i z div per s t e p ()k div 9m per div 5 ma i gt
an1006 application notes http://www.teccor.com an1006 - 10 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog procedure 12: i gt ? quadrant ii [mt2 (+) gate (-)] to measure the i gt ? quadrant ii parameter: 1. set step/offside polarity by depressing invert (release but- ton on 577). 2. set polarity to (+). 3. set observed dot to bottom right corner of crt grid by turn- ing the horizontal position knob. when quadrant ii testing is complete, return dot to original position. 4. repeat procedure 11. procedure 13: i gt ? quadrant iii [mt2 (-) gate (-)] to measure the i gt ? quadrant iii parameter: 1. set polarity to (?). 2. set step/offset polarity to non-inverted position (button extended, on 577 button depressed). 3. repeat procedure 11. (figure an1006.15) figure an1006.15 i gt in quadrant iii = 27 ma procedure 14: i gt ? quadrant iv [mt2 (-) gate (+)] to measure the i gt ? quadrant iv parameter: 1. set polarity to (?). 2. set step/offset polarity by depressing invert (release but- ton on 577). 3. set observed dot to top left corner of crt grid by turning the horizontal position knob. when quadrant iv testing is com- plete, return dot to original position. 4. repeat procedure 11. procedure 15: v gt to measure the v gt parameter: 1. set polarity to (+). 2. set number of steps to 1 . (set steps to 0 (zero) on 370.) 3. set offset by depressing aid. (on 577, also set 0 (zero) but- ton to offset . button is extended.) 4. set offset multiplier to 0 (zero). (press aid and o ppose at same time on 370.) 5. set terminal selector to step generator-emitter grounded . 6. set mode to norm . 7. set max peak volts to 15 v . ( 16 v on 370) 8. set power dissipation to 10 w . 9. set step family by depressing single . 10. set horizontal knob to 2 v/div . 11. set step/offset polarity to non-inverted position (button extended, on 577 button depressed). 12. set current limit to 500 ma (not available on 577). 13. increase variable collector supply voltage until voltage reaches 12 v on crt. 14. after 12 v setting is complete, change horizontal knob to step generator. procedure 16: v gt ? quadrant i [mt2 (+) gate (+)] to measure the v gt ? quadrant i parameter: 1. set step/offset amplitude to 20% of rated v gt . 2. set left-right terminal jack selector to correspond with location of test fixture. 3. gradually increase offset multiplier until device reaches conduction point. (figure an1006.16) measure v gt by fol- lowing horizontal axis to the point where the vertical line passes through the axis. this measured value will be v gt . (on 370, v gt will be numerically displayed on screen under offset value.) figure an1006.16 v gt in quadrant i = 780 mv procedure 17: v gt ? quadrant ii [mt2 (+) gate (-)] to measure the v gt ? quadrant ii parameter: 1. set step/offset polarity by depressing invert (release but- ton on 577). 2. set polarity to (+). 3. set observed dot to bottom right corner of crt grid by turn- ing the horizontal position knob. when quadrant ii testing is complete, return dot to original position. 4. repeat procedure 16. procedure 18: v gt ? quadrant iii [mt2 (-) gate (-)] to measure the v gt ? quadrant iii parameter: 1. set polarity to (?). 2. set step/offset polarity to non-inverted position (button extended, on 577 button depressed). 50 ma 10 per v e r t div per h o r i z div per s t e p ()k div 9m per div 5 ma i gt 50 ma 500 mv per v e r t div per h o r i z div per s t e p ()k div 9m per div 100m v gt
application notes an1006 ?2002 teccor electronics an1006 - 11 http://www.teccor.com thyristor product catalog +1 972-580-7777 3. repeat procedure 16. (figure an1006.17) figure an1006.17 v gt in quadrant iii = 820 mv procedure 19: v gt ? quadrant iv [mt2 (-) gate (+)] to measure the v gt ? quadrant iv parameter: 1. set polarity to (?). 2. set step/offset polarity by depressing invert (release but- ton on 577). 3. set observed dot to top left corner of crt grid by turning the horizontal position knob. when testing is complete in quad- rant iv, return dot to original position. 4. repeat procedure 16. quadracs quadracs are simply triacs with an internally-mounted diac. as with triacs, quadracs are bidirectional ac switches which are gate controlled for either polarity of main terminal voltage. to connect the quadrac : 1. connect trigger to base terminal (b). 2. connect mt1 to emitter terminal (e). 3. connect mt2 to collector terminal (c). to begin testing, perform the following procedures. procedure 1: (+)v drm , (+)i drm , (-)v drm , (-)i drm note: the (+) and (-) symbols are used to designate the polarity of mt2 with reference to mt1. to measure the (+)v drm , (+)i drm , (-)v drm , and (-)i drm parameter: 1. set variable collector supply voltage range to appropri- ate max peak volts for device under test. (value selected should be equal to or greater than the device?s v drm rating). 2. set horizontal knob to sufficient scale to allow v iewing of trace at the required voltage level. (the 100 v/div scale should be used for testing devices having a v drm rating of 600 v or greater; the 50 v/div scale for testing parts rated from 300 v to 500 v, and so on). 3. set mode to leakage . 4. set polarity to (+). 5. set power dissipation to 0.5 w . ( 0.4 w on 370) 6. set terminal selector to emitter grounded-open base. 7. set vertical knob to ten times the maximum leakage current (i drm ) specified for the device. note: the crt readout should show 1% of the maximum leakage current. the vertical scale is divided by 1,000 when the leakage mode is used. procedure 2: (+)v drm and (+)i drm to measure the (+)v drm and (+)i drm parameter: 1. set left-right terminal jack selector to correspond with the location of the test fixture. 2. increase variable collector supply voltage to the rated v drm of the device and observe the dot on the crt. (read across horizontally from the dot to the vertical current scale.) this measured value is the leakage current. (figure an1006.18) warning: do not exceed v drm /v rrm rating of scrs, triacs, or quadracs . these devices can be damaged. figure an1006.18 (+)i drm = 51 na at (+)v drm = 400 v procedure 3: (-)v drm and (-)i drm to measure the (-)v drm and (-)i drm parameter: 1. set polarity to (?). 2. repeat procedures 1 and 2. (read measurements from upper right corner of screen). procedure 4: v bo , i bo , ? v bo ( quadrac trigger diac or discrete diac) to connect the quadrac : 1. connect mt1 to emitter terminal (e). 2. connect mt2 to collector terminal (c). 3. connect trigger terminal to mt2 terminal through a 10 ? resistor. to measure the v bo , i bo , and ? v bo parameter: 1. set variable collector supply voltage range to 75 max peak volts. ( 80 v on 370) 2. set horizontal knob to 10 v/div . 3. set vertical knob to 50 a/div . 4. set polarity to ac . 5. set mode to norm . 6. set power dissipation to 0.5 w . ( 0.4 w on 370) 50 ma 100m per v e r t div per h o r i z div per s t e p ()k div 9m per div 500 mv v gt 50 na 50 v per v e r t div per h o r i z div per s t e p ()k div 9m per div v drm i drm
an1006 application notes http://www.teccor.com an1006 - 12 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog 7. set terminal selector to emitter grounded-open base . procedure 5: v bo (positive and negative) to measure the v bo (positive and negative) parameter: 1. set left-right terminal jack selector to correspond with the location of the test fixture. 2. set variable collector supply voltage to 55 v ( 65 v on 370) and apply voltage to the device under test (d.u.t.) using the left hand selector switch. the peak voltage at which current begins to flow is the v bo value. (figure an1006.19) figure an1006.19 (+)v bo = 35 v; (-)v bo = 36 v; ()i bo < 10 a procedure 6: i bo (positive and negative) to measure the i bo (positive and negative) parameter, at the v bo point, measure the amount of device current just before the device reaches the breakover point. the measured current at this point is the i bo value. note: if i bo is less than 10 a, the current cannot readily be seen on curve tracer. procedure 7: ? v bo (voltage breakover symmetry) to measure the ? v bo (voltage breakover symmetry) parameter: 1. measure positive and negative v bo values per procedure 5. 2. subtract the absolute value of v bo (-) from v bo (+). the absolute value of the result is: ? v bo = [ i+v bo i - i -v bo i ] procedure 8: v tm (forward and reverse) to test v tm , the quadrac must be connected the same as when testing v bo , i bo , and ? v bo . to connect the quadrac : 1. connect mt1 to emitter terminal (e). 2. connect mt2 to collector terminal (c). 3. connect trigger terminal to mt2 terminal through a 10 ? resistor. note the following: ? due to the excessive amount of power that can be generated in this test, only parts with an i t(rms) rating of 8 a or less should be tested on standard curve tracer. if testing devices above 8 a, a tektronix model 176 high-current module is required. ? a kelvin test fixture is required for this test. if a kelvin fixture is not used, an error in measurement of v tm will result due to volt- age drop in fixture. if a kelvin fixture is not available, figure an1006.3 shows necessary information to wire a test fixture with kelvin connections. to measure the v tm (forward and reverse) parameter: 1. set terminal selector to emitter grounded-open base . 2. set max peak volts to 75 v . ( 80 v on 370) 3. set mode to norm . 4. set horizontal knob to 0.5 v/div . 5. set power dissipation to 220 watts ( 100 watts on a 577). 6. set vertical knob to a sufficient setting to allow the viewing of 1.4 times the i t(rms) rating of the device i t(peak) on the crt. procedure 9: v tm(forward) to measure the v tm (forward) parameter: 1. set polarity to (+). 2. set left-right terminal jack selector to correspond with the location of the test fixture. 3. increase variable collector supply voltage until current reaches rated i t(peak) , which is 1.4 times the i t(rms) rating of the triac under test. note: model 370 current is limited to 10 a. warning: limit test time to 15 seconds maximum. 4. to measure v tm , follow along horizontal scale to the point where the trace crosses the i t(peak) value. this horizontal dis- tance is the v tm value. (figure an1006.20) figure an1006.20 v tm (forward) = 1.1 v at i pk = 5.6 a procedure 10: v tm(reverse) to measure the v tm (reverse) parameter: 1. set polarity to (?). 2. set left-right terminal jack selector to correspond with the location of the test fixture. 3. increase variable collector supply voltage until current reaches rated i t(peak) . 4. measure v tm(reverse) the same as in procedure 8. (read mea- surements from upper right corner of screen). 50 a 10 v per v e r t div per h o r i z div per s t e p ()k div 9m per div v bo i bo +v bo +i bo 500 mv per v e r t div per h o r i z div per s t e p i pk v tm 1 a ()k div 9m per div
application notes an1006 ?2002 teccor electronics an1006 - 13 http://www.teccor.com thyristor product catalog +1 972-580-7777 procedure 11: i h(forward and reverse) for these steps, it is again necessary to connect the trigger to mt2 through a 10 ? resistor. the other connections remain the same. to measure the i h (forward and reverse) parameter: 1. set power dissipation to 50 w. 2. set max peak volts to 75 v. ( 80 v on 370) 3. set mode to dc . 4. set horizontal knob to 5 v/div. 5. set vertical knob to approximately 10% of the maximum i h specified. note: due to large variations of holding current values, the scale may have to be adjusted to observe holding current. 6. set terminal selector to emitter grounded-open base. procedure 12: i h(forward) to measure the i h (forward) parameter: 1. set polarity to (+). 2. set left-right terminal jack selector to correspond with the location of the test fixture. 3. increase variable collector supply voltage to maximum position ( 100 ). note: depending on the vertical scale being used, the dot may disappear completely from the screen. 4. decrease variable collector supply voltage to the point where the line on the crt changes to a dot. the position of the beginning point of the line, just before the line changes to a dot, represents the i h value. (figure an1006.21) figure an1006.21 i h (forward) = 18 ma procedure 13: i h(reverse) to measure the i h (reverse) parameter: 1. set polarity to (?). 2. continue testing per procedure 12 for measuring i h (reverse) . sidacs the sidac is a bidirectional voltage-triggered switch. upon appli- cation of a voltage exceeding the sidac breakover voltage point, the sidac switches on through a negative resistance region (simi- lar to a diac) to a low on-state voltage. conduction continues until current is interrupted or drops below minimum required holding current. to connect the sidac: 1. connect mt1 to the emitter terminal (e). 2. connect mt2 to the collector terminal (c). to begin testing, perform the following procedures. procedure 1: (+) v drm , (+)i drm , (-)v drm , (-)i drm note: the (+) and (-) symbols are used to designate the polarity of mt2 with reference to mt1. to measure the (+)v drm , (+)i drm , (-)v drm , and (-)i drm parameter: 1. set variable collector supply voltage range to 1500 max peak volts . 2. set horizontal knob to 50 v/div. 3. set mode to leakage . 4. set polarity to (+). 5. set power dissipation to 2.2 w . ( 2w on 370) 6. set terminal selector to emitter grounded-open base . 7. set vertical knob to 50 a/div. (due to leakage mode, the crt readout will show 50 na.) procedure 2: (+)v drm and (+)i drm to measure the (+)v drm and (+)i drm parameter: 1. set left-right terminal jack selector to correspond with the location of the test fixture. 2. increase variable collector supply voltage to the rated v drm of the device and observe the dot on the crt. read across horizontally from the dot to the vertical current scale. this measured value is the leakage current. (figure an1006.22) figure an1006.22 i drm = 50 na at v drm = 90 v 5 ma 5 v per v e r t div per h o r i z div per s t e p ()k div 9m per div i h 50 na 50 v per v e r t div per h o r i z div per s t e p ()k div 9m per div v drm i drm
an1006 application notes http://www.teccor.com an1006 - 14 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog procedure 3: (-) v drm and (-) i drm to measure the (-)v drm and (-)i drm parameter: 1. set polarity to (?). 2. repeat procedures 1 and 2. (read measurements from upper right corner of the screen). procedure 4: v bo and i bo to measure the v bo and i bo parameter: 1. set variable collector supply voltage range to 1500 max peak volts. ( 2000 v on 370) 2. set horizontal knob to a sufficient scale to allow viewing of trace at the required voltage level ( 50 v/div for 95 v to 215 v v bo range devices and 100 v/div for devices having v bo 15 v). 3. set vertical knob to 50 a/div. 4. set polarity to ac. 5. set mode to norm . 6. set power dissipation to 10 w . 7. set terminal selector to emitter grounded-open base . 8. set left-right terminal jack selector to correspond with location of test fixture. procedure 5: v bo to measure the v bo parameter, increase variable collector supply voltage until breakover occurs. (figure an1006.23) the voltage at which current begins to flow and voltage on crt does not increase is the v bo value. figure an1006.23 (+)v bo = 100 v; (-)v bo = 100 v; ()i bo < 10 a procedure 6: i bo to measure the i bo parameter, at the v bo point, measure the amount of device current just before the device reaches the breakover mode. the measured current at this point is the i bo value. note: if i bo is less than 10 a, the current cannot readily be seen on the curve tracer. procedure 7: i h(forward and reverse) to measure the i h (forward and reverse) parameter: 1. set variable collector supply voltage range to 1500 max peak volts ( 400 v on 577; 2000 v on 370). 2. set horizontal knob to a sufficient scale to allow viewing of trace at the required voltage level ( 50 v/div for devices with v bo range from 95 v to 215 v and 100 v/div for devices having v bo 215 v). 3. set vertical knob to 20% of maximum holding current speci- fied. 4. set polarity to ac. 5. set mode to norm. 6. set power dissipation to 220 w ( 100 w on 577). 7. set terminal selector to emitter grounded-open base. 8. set left-right terminal jack selector to correspond with the location of the test fixture. warning: limit test time to 15 seconds maximum. 9. increase variable collector supply voltage until device breaks over and turns on. (figure an1006.24) figure an1006.24 i h = 48 ma in both forward and reverse directions i h is the vertical distance between the center horizontal axis and the beginning of the line located on center vertical axis. procedure 8: v tm(forward and reverse) to measure the v tm (forward and reverse) parameter: 1. set variable collector supply voltage range to 350 max peak volts. ( 400 v on 370) 2. set horizontal knob to 0.5 v/div. 3. set vertical knob to 0.5 a/div. 4. set polarity to (+). 5. set mode to norm. 6. set power dissipation to 220 w ( 100 w on 577). 7. set terminal selector to emitter grounded-open base. before continuing with testing, note the following: ? a kelvin test fixture is required for this test. if a kelvin fixture is not used, an error in measurement of v tm will result due to volt- age drop in fixture. if a kelvin fixture is not available, figure an1006.3 shows necessary information to wire a test fixture with kelvin connections. 50 a 50 v per v e r t div per h o r i z div per s t e p ()k div 9m per div v bo +v bo +i bo i bo 20 ma 50 v per v e r t div per h o r i z div per s t e p ()k div 9m per div i h i h
application notes an1006 ?2002 teccor electronics an1006 - 15 http://www.teccor.com thyristor product catalog +1 972-580-7777 to continue testing, perform the following procedures. procedure 9: v tm(forward) to measure the v tm (forward) parameter: 1. set left-right terminal jack selector to correspond with the location of the test fixture. 2. increase variable collector supply voltage until current reaches rated i t(peak) , which is 1.4 times the i t(rms) rating of the sidac. note: model 370 current is limited. set to 400 ma. check for 1.1 v max. warning: limit test time to 15 seconds. 3. to measure v tm , follow along horizontal scale to the point where the trace crosses the i t(peak) value. this horizontal dis- tance is the v tm value. (figure an1006.25) figure an1006.25 v tm (forward) = 950 mv at i pk = 1.4 a procedure 10: v tm(reverse) to measure the v tm (reverse) parameter: 1. set polarity to (?). 2. repeat procedure 8 to measure v tm(reverse) . diacs diacs are voltage breakdown switches used to trigger-on triacs and non-sensitive scrs in phase control circuits. note: diacs are bi-directional devices and can be connected in either direction. to connect the diac: 1. connect one side of the diac to the collector terminal (c). 2. connect other side of the diac to the emitter terminal (e). to begin testing, perform the following procedures. procedure 1: curve tracer setup to set the curve tracer and begin testing: 1. set variable collector supply voltage range to 75 max peak volts. ( 80 v on 370) 2. set horizontal knob to sufficient scale to allow viewing of trace at the required voltage level ( 10 v to 20 v/div depend- ing on device being tested). 3. set vertical knob to 50 a/div. 4. set polarity to ac. 5. set mode to norm. 6. set power dissipation to 0.5 w . ( 0.4 w on 370) 7. set terminal selector to emitter grounded-open base. procedure 2: v bo to measure the v bo parameter: 1. set left-right terminal jack selector to correspond with the location of the test fixture. 2. set variable collector supply voltage to 55 v ( 65 v for 370) and apply voltage to device under test (d.u.t.), using left-right-selector switch . the peak voltage at which cur- rent begins to flow is the v bo value. (figure an1006.26) figure an1006.26 (+)v bo = 35 v; (-)v bo = 36 v; ()i bo < 15 a; (-)i bo < 10 a and cannot be read easily procedure 3: i bo to measure the i bo parameter, at the v bo point, measure the amount of device current just before the device reaches the breakover mode. the measured current at this point is the i bo value. note: if i bo is less than 10 a, the current cannot readily be seen on the curve tracer. procedure 4: ? v bo(voltage breakover symmetry) to measure the ? v bo (voltage breakover symmetry) parameter: 1. measure positive and negative values of v bo as shown in figure an1006.26. 2. subtract the absolute value of v bo (-) from v bo (+). the absolute value of the result is: ? v bo = [ i +v bo i - i -v bo i ] 500 ma 500 mv per v e r t div per h o r i z div per s t e p ()k div 9m per div v tm i pk 50 a 10 v per v e r t div per h o r i z div per s t e p ()k div 9m per div +v bo +i bo i bo v bo
an1006 application notes http://www.teccor.com an1006 - 16 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog model 370 curve tracer procedure notes because the curve tracer procedures in this application note are written for the tektronix model 576 curve tracer, certain settings must be adjusted when using model 370. variable collector sup- ply voltage range and power dissipation controls have different scales than model 576. the following table shows the guidelines for setting power dissipation when using model 370. (figure an1006.27) although the maximum power setting on the model 370 curve tracer is 200 w, the maximum collector voltage available is only 400 v at 220 w. the following table shows the guidelines for adapting collector supply voltage range settings for model 370 curve tracer procedures: the following table shows the guidelines for adapting terminal selector knob settings for model 370 curve tracer procedures: model 576 model 370 if power dissipation is 0.1 w, set at 0.08 w. if power dissipation is 0.5 w, set at 0.4 w. if power dissipation is 2.2 w, set at 2 w. if power dissipation is 10 w, set at 10 w. if power dissipation is 50 w, set at 50 w. if power dissipation is 220 w, set at 220 w. model 576 model 370 if voltage range is 15 v, set at 16 v. if voltage range is 75 v, set at 80 v. if voltage range is 350 v, set at 400 v. if voltage range is 1500 v, set at 2000 v. model 576 model 370 if step generator (base) is emitter grounded, then base step generator is emitter common. if emitter grounded is open base, then base open is emitter common.
application notes an1006 ?2002 teccor electronics an1006 - 17 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1006.27 tektronix model 370 curve tracer programmable curve tracer setup memory display intensity position gpib plotter step generator aux sipply step/offset amplitude cursor measurement horizontal volts/div vertical current/div offset polarity collector supply collector supply variable c b e c sense e sense b sense c b e c sense e sense b sense power max peak power watts terminal jacks gate/trigger mt2/anode mt1/cathode variable collector supply voltage range terminal selector variable collector supply voltage max peak power (power dissipation) offset step/offset amplitude (amps/volts) step/offset polarity horizontal voltage control note: all voltage settings will be referenced to "collector" crt left-right selector for terminal jacks left right both kelvin terminals used when measuring v tm or v fm collector step family max peak volts polarity vert/div cursor horz/div cursor per step offset or gm/div aux supply configuration
an1006 application notes http://www.teccor.com an1006 - 18 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog model 577 curve tracer procedure notes because the curve tracer procedures in this application note are written for the tektronix model 576 curve tracer, certain sett ings must be adjusted when using model 577. model 576 curve tracer has separate controls for polarity (ac,+,-) and mode (norm, dc, leakag e), whereas model 577 has only a polarity control. the following table shows the guidelines for setting collector supply polarity wh en using model 577. (figure an1006.28) one difference between models 576 and 577 is the step/offset polarity setting. the polarity is inverted when the button is depressed on the model 576 curve tracer. the model 577 is opposite ? the step/offset polarity is ?inverted? when the button is extended and ?normal? when the button is depressed. the step/offset polarity is used only when measuring i gt and v gt of triacs and quadracs in quadrants l through lv. also, the variable collector supply voltage range and power dissipation controls have different scales than model 576. the following table shows the guidelines for setting power dissipation when using model 577. although the maximum power setting on model 576 curve tracer is 220 w (compared to 100 w for model 577), the maximum col- lector current available is approximately the same. this is due to the minimum voltage range on model 577 curve tracer being 6.5 v compared to 15 v for model 576. the following table shows the guidelines for adapting collector voltage supply range set- tings for model 577 curve tracer procedures: model 576 model 577 if using leakage mode along with polarity setting of +(npn) and -(pnp), [vertical scale divided by 1,000], set collector supply polarity to either +dc or -dc , depending on polarity setting specified in the procedure. the vertical scale is read directly from the scale on the control knob. if using dc mode along with either +(npn) or -(pnp) polarity, set collector supply polarity to either +dc or -dc depending on polarity specified. if using norm mode along with either +(npn) or -(pnp) polarity, set collector supply polarity to either +(npn) or -(pnp) per specified procedure. if using norm mode with ac polarity, set collector supply polarity to ac . model 576 model 577 if power dissipation is 0.1 w, set at 0.15 w. if power dissipation is 0.5 w, set at 0.6 w. if power dissipation is 2.2 w, set at 2.3 w. if power dissipation is 10 w, set at 9 w. if power dissipation is 50 w, set at 30 w. if power dissipation is 220 w, set at 100 w. model 576 model 577 if voltage range is 15 v, set at either 6.5 v or 25 v, depending on parameter being tested. set at 6.5 v when measuring v tm (to allow maximum collector current) and set at 25 v when measuring i gt and v gt . if voltage range is 75 v, set at 100 v. if voltage range is 1500 v, set at 1600 v.
application notes an1006 ?2002 teccor electronics an1006 - 19 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1006.28 tektronix model 577 curve tracer brightness store intensity focus power step/offset amplifier polarity offset multi position position display max peak volts variable collector% collector supply polarity step rate collector supply terminal jacks sense sense sense sense c b e c b e e e cc kelvin terminals used when measuring v tm or v fm variable voltage looping compensation step gen output (off) variable output ext base or emit input vertical right left avoid extremely bright display adjust for best focus step generator section number of steps step/offset polarity horizontal voltage control note: all voltage settings will be referenced to "collector" indicates dangerous voltages on test jacks vertical current supply left-right selector for terminal jacks indicates collector supply disabled watch high power settings. can damage device under test max peak power (power dissipation) variable collector supply voltage range crt variable collector supply voltage mt1/cathode gate/trigger mt2/anode terminal selector ground beam finder step family
notes
?2002 teccor electronics an1007 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 7 thyristors used as ac st atic switches and relays introduction since the scr and the triac are bistable devices, one of their broad areas of application is in the realm of signal and power switching. this application note describes circuits in which these thyristors are used to perform simple switching functions of a general type that might also be performed non-statically by vari- ous mechanical and electromechanical switches. in these appli- cations, the thyristors are used to open or close a circuit completely, as opposed to applications in which they are used to control the magnitude of average voltage or energy being deliv- ered to a load. these latter types of applications are described in detail in ?phase control using thyristors? (an1003). static ac switches normally open circuit the circuit shown in figure an1007.1 provides random (any- where in half-cycle), fast turn-on (<10 s) of ac power loads and is ideal for applications with a high-duty cycle. it eliminates com- pletely the contact sticking, bounce, and wear associated with conventional electromechanical relays, contactors, and so on. as a substitute for control relays, thyristors can overcome the differ- ential problem; that is, the spread in current or voltage between pickup and dropout because thyristors effectively drop out every half cycle. also, providing resistor r 1 is chosen correctly, the cir- cuits are operable over a much wider voltage range than is a comparable relay. resistor r 1 is provided to limit gate current (i gtm ) peaks. its resistance plus any contact resistance (r c ) of the control device and load resistance (r l ) should be just greater than the peak supply voltage divided by the peak gate current rating of the triac. if r 1 is set too high, the triacs may not trigger at the beginning of each cycle, and phase control of the load will result with consequent loss of load voltage and waveform distor- tion. for inductive loads, an rc snubber circuit, as shown in fig- ure an1007.1, is required. however, a snubber circuit is not required when an alternistor is used. figure an1007.2 illustrates an analysis to better understand a typical static switch circuit. the circuit operation occurs when switch s 1 is closed, since the triac q 1 will initially be in the block- ing condition. current flow will be through load r l , s 1 , r 1 , and gate to mt1 junction of the thyristor. when this current reaches the required value of i gt , the mt2 to mt1 junctions will switch to the conduction state and the voltage from mt2 to mt1 will be v t . as the current approaches the zero crossing, the load current will fall below holding current turning the triac q 1 device off until it is refired in the next half cycle. figure an1007.3 illustrates the volt- age waveform appearing across the mt2 to mt1 terminals of q 1 . note that the maximum peak value of current which s 1 will carry would be 25 ma since q 1 has a 25 ma maximum i gt rating. addi- tionally, no arcing of a current value greater than 25 ma when opening s 1 will occur when controlling an inductive load. it is important also to note that the triac q 1 is operating in quadrants i and iii, the more sensitive and most suitable gating modes for tri- acs. the voltage rating of s 1 (mechanical switch or reed switch) must be equivalent to or greater than line voltage applied. figure an1007.1 basic triac static switch figure an1007.2 analysis of static switch load r l r 1 100 ? r 2 100 ? s 1 control device reed switch for inductive loads c 1 0.1 f tr i a c r 1 2? v (r l + r c ) where i gtm is peak gate current rating of triac i gtm v rms mt1 i gt mt2 ac voltage input 120 v rms, 60 hz v in r l s 1 i gt v gt q 1 + - load r 1 g q2008l4 an1007
an1007 application notes http://www.teccor.com an1007 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1007.3 waveform across static switch a typical example would be in the application of this type circuit for the control of 5 a resistive load with 120 v rms input voltage. choosing a value of 100 ? for r 1 and assuming a typical value of 1 v for the gate to mt1 (v gt ) voltage, we can solve for v p by the following: v p = i gt (r l + r 1 ) + v gt note: r c is not included since it is negligible. v p = 0.025 (24 + 100) + 1.0 = 4.1 v additionally the turn-on angle is [ = 1.4] the power lost by the turn-on angle is essentially zero. the power dissipation in the gate resistor is very minute. a 100 ? , 0.25 w rated resistor may safely be used. the small turn-on angle also ensures that no appreciable rfi is generated. the relay circuit shown in figure an1007.1 and figure an1007.2 has several advantages in that it eliminates contact bounce, noise, and additional power consumption by an energizing coil and can carry an in-rush current of many times its steady state rating. the control device s 1 indicated can be either electrical or mechanical in nature. light-dependent resistors and light- acti- vated semiconductors, optocoupler, magnetic cores, and mag- netic reed switches are all suitable control elements. regardless of the switch type chosen, it must have a voltage rating equal to or greater than the peak line voltage applied. in particular, the use of hermetically sealed reed switches as control elements in combination with triacs offers many advantages. the reed switch can be actuated by passing dc current through a small coiled wire or by the proximity of a small magnet. in either case, com- plete electrical isolation exists between the control signal input, which may be derived from many sources, and the switched power output. long life of the triac/reed switch combination is ensured by the minimal volt-ampere switching load placed on the reed switch by the triac triggering requirements. the thyristor rat- ings determine the amount of load power that can be switched. normally closed circuit with a few additional components, the thyristor can provide a normally closed static switch function. the critical design portion of this static switch is a clamping device to turn off/eliminate gate drive and maintain very low power dissipation through the clamp- ing component plus have low by-pass leakage around the power thyristor device. in selecting the power thyristor for load require- ments, gate sensitivity becomes critical to maintain low power requirements. either sensitive scrs or sensitive logic triacs must be considered, which limits the load in current capacity and type. however, this can be broader if an extra stage of circuitry for gat- ing is permitted. figure an1007.4 illustrates an application using a normally closed circuit driving a sensitive scr for a simple but precise temperature controller. the same basic principle could be applied to a water level controller for a motor or solenoid. of course, scr and diode selection would be changed depending on load current requirements. figure an1007.4 normally closed temperature controller a mercury-in-glass thermostat is an extremely sensitive measur- ing instrument, capable of sensing changes in temperature as small as 0.1 c. its major limitation lies in its very low current- handling capability for reliability and long life, and contact current should be held below 1 ma. in the circuit of figure an1007.4, the s2010ls2 scr serves as both current amplifier for the hg ther- mostat and as the main load switching element. with the thermostat open, the scr will trigger each half cycle and deliver power to the heater load. when the thermostat closes, the scr can no longer trigger and the heater shuts off. maximum current through the thermostat in the closed position is less than 250 a rms. figure an1007.5 shows an all solid state, optocoupled, normally closed switch circuit. by using a low voltage sbs triggering device, this circuit can turn on with only a small delay in each half cycle and also keep gating power low. when the optocoupled transistor is turned on, the gate drive is removed with only a few milliamps of bypass current around the triac power device. also, by use of the bs08d and 0.1 f, less sensitive triacs and alter- nistors can be used to control various types of high current loads. 120 v rms (170 v peak) v p - ? 1 v rms or 1.6 v peak max v p + v t + v t - sin 1 ? 4.1 170v pk --------------------- = 1000 w heater load 120 v ac 60 cps d2015l cr 1 ?cr 4 cr 4 cr 3 cr 1 cr 2 s2010ls2 0.1 f r 1 510 k scr 1 twist leads to minimize pickup hg in glass thermostat
application notes an1007 ?2002 teccor electronics an1007 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1007.5 normally closed switch circuit optocoupled driver circuits random turn-on, normally open many applications use optocouplers to drive thyristors. the com- bination of a good optocoupler and a triac or alternistor makes an excellent, inexpensive solid state relay. application information provided by the optocoupler manufacturers is not always best for application of the power thyristor. figure an1007.6 shows a stan- dard circuit for a resistive load. figure an1007.6 optocoupled circuit for resistive loads (triac or alternistor) a common mistake in this circuit is to make the series gate resis- tor too large in value. a value of 180 ? is shown in a typical appli- cation circuit by optocoupler manufacturers. the 180 ? is based on limiting the current to 1 a peak at the peak of a 120 v line input. this is good for protection of the optocoupler output triac, as well as the gate of the power triac on a 120 v line; however, it must be lowered if a 24 v line is being controlled, or if the r l (resistive load) is 200 w or less. this resistor limits current for worst case turn-on at the peak line voltage, but it also sets turn- on point (conduction angle) in the sine wave, since triac gate cur- rent is determined by this resistor and produced from the sine wave voltage as illustrated in figure an1007.2. the load resis- tance is also important, since it can also limit the amount of avail- able triac gate current. a 100 ? gate resistor would be a better choice in most 120 v applications with loads greater than 200 w and optocouplers from quality technologies or vishay with opto- coupler output triacs that can handle 1.7 a pk (i tsm rating) for a few microseconds at the peak of the line. for loads less than 200 w, the resistor can be dropped to 22 ? . remember that if the gate resistor is too large in value, the triac will not turn on at all or not turn on fully, which can cause excessive power dissipation in the gate resistor, causing it to burn out. also, the voltage and dv/ dt rating of the optocoupler's output device must be equal to or greater than the voltage and dv/dt rating of the triac or alternistor it is driving. figure an1007.7 illustrates a circuit with a dv/dt snubber network included. this is a typical circuit presented by optocoupler manu- facturers. figure an1007.7 optocoupler circuit for inductive loads (triac or alternistor) this ?t? circuit hinges around one capacitor to increase dv/dt capability to either the optocoupler output triac or the power triac. the sum of the two resistors then forms the triac gate resistor. both resistors should then be standardized and lowered to 100 ? . again, this sum resistance needs to be low, allowing as much gate current as possible without exceeding the instanta- neous current rating of the opto output triac or triac gate junction. by having 100 ? for current limit in either direction from the capacitor, the optocoupler output triac and power triac can be protected against di/dt produced by the capacitor. of course, it is most important that the capacitor be connected between proper terminals of triac. for example, if the capacitor and series resis- tor are accidentally connected between the gate and mt2, the triac will turn on from current produced by the capacitor, resulting in loss of control. for low current (ma) and/or highly inductive loads, it may be nec- essary to have a latching network (3.3 k ? + 0.047 f) connected directly across the power triac. the circuit shown in figure an1007.8 illustrates the additional latching network. load triac 51 k 0.02 f (4) in4004 ps2502 + 120 v ac q2008l4 bs08d r in v cc 1 6 4 180 g r l 120 v 60 hz mt2 mt1 hot neutral load could be in either le g 2 r in v cc 1 6 4 100 g neutral 2 100 z l 120 v 60 hz mt2 mt1 hot 0.1 f c 1
an1007 application notes http://www.teccor.com an1007 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1007.8 optocoupler circuit for lower current inductive loads (triac or alternistor) in this circuit, the series gate resistors are increased to 180 ? each, since a 240 v line is applied. note that the load is placed on the mt1 side of the power triac to illustrate that load place- ment is not important for the circuit to function properly. also note that with standard u.s. residential 240 v home wiring, both sides of the line are hot with respect to ground (no neutral). therefore, for some 240 v line applications, it will be necessary to have a triac switch circuit in both sides of the 240 v line input. if an application requires back-to-back scrs instead of a triac or alternistor, the circuit shown in figure an1007.9 may be used. figure an1007.9 optocoupled circuit for heavy-duty inductive loads all application comments and recommendations for optocoupled switches apply to this circuit. however, the snubber network can be applied only across the scrs as shown in the illustration. the optocoupler should be chosen for best noise immunity. also, the voltage rating of the optocoupler output triac must be equal to or greater than the voltage rating of scrs. summary of random turn-on relays as shown in figure an1007.10, if the voltage across the load is to be phase controlled, the input control circuitry must be syn- chronized to the line frequency and the trigger pulses delayed from zero crossing every half cycle. if the series gate resistor is chosen to limit the peak current through the opto-driver to less than 1 a, then on a 120 v ac line the peak voltage is 170 v; therefore, the resistor is 180 ? . on a 240 v ac line the peak volt- age is 340 v; therefore, the resistor should be 360 ? . these gate pulses are only as long as the device takes to turn on (typically, 5 s to 6 s); therefore, 0.25 w resistor is adequate. figure an1007.10 random turn-on triac driver select the triac for the voltage of the line being used, the current through the load, and the type of load. since the peak voltage of a 120 v ac line is 170 v, you would choose a 200 v (min) device. if the application is used in an electrically noisy industrial envi- ronment, a 400 v device should be used. if the line voltage to be controlled is 240 v ac with a peak voltage of 340 v, then use at least a 400 v rated part or 600 v for more design margin. selec- tion of the voltage rating of the opto-driver must be the same or higher than the rating of the power triac. in electrically noisy industrial locations, the dv/dt rating of the opto-driver and the triac must be considered. the rms current through the load and main terminals of the triac should be approximately 70% of the maximum rating of the device. however, a 40 a triac should not be chosen to control a 1 a load due to low latching and holding current requirements. remember that the case temperature of the triac must be main- tained at or below the current versus temperature curve specified on its data sheet. as with all semiconductors the lower the case temperature the better the reliability. opto-driven gates normally do not use a sensitive gate triac. the opto-driver can supply up to 1 a gate pulses and less sensitive gate triacs have better dv/dt capability. if the load is resistive, it is acceptable to use a stan- dard triac. however, if the load is a heavy inductive type, then an alternistor triac, or back-to-back scrs as shown in figure an1007.9, is recommended. a series rc snubber network may or may not be necessary when using an alternistor triac. nor- mally a snubber network is not needed when using an alternistor because of its high dv/dt and dv/dt(c) capabilities. however, latching network as described in figure an1007.8 may be needed for low current load variations. zero crossing turn-on, normally open relay circuits when a power circuit is mechanically switched on and off mechanically, generated high-frequency components are gener- ated that can cause interference problems such as rfi. when power is initially applied, a step function of voltage is applied to the circuit which causes a shock excitation. random switch opening stops current off, again generating high frequencies. in addition, abrupt current interruption in an inductive circuit can lead to high induced-voltage transients. the latching characteristics of thyristors are ideal for eliminating interference problems due to current interruption since these devices can only turn off when the on-state current approaches zero, regardless of load power factor. on the other hand, interference-free turn-on with thyristors requires special trigger circuits. it has been proven experimen- 6 r in v cc 1 180 g 240 v ac mt2 mt1 2 180 0.1 f 3 4 5 0.047 f 3.3 k load r in v cc 1 g 120 v ac 2 3 0.1 f load 6 4 5 100 k a 100 g a k ns-scr ns- scr tr i a c o r alternistor mt2 0.1 f 100 ? load mt1 hot neutral 120/240 v ac g 180 ? for 120 v ac 360 ? for 240 v ac input r in 1 6 5 4 3 2 load could be here instead of lower location
application notes an1007 ?2002 teccor electronics an1007 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 tally that general purpose ac circuits will generate minimum electromagnetic interference (emi) if energized at zero voltage. the ideal ac circuit switch, therefore, consists of a contact which closes at the instant when voltage across it is zero and opens at the instant when current through it is zero. this has become known as ?zero-voltage switching.? for applications that require synchronized zero-crossing turn-on, the illustration in figure an1007.11 shows a circuit which incor- porates an optocoupler with a built-in zero-crossing detector figure an1007.11 optocoupled circuit with zero-crossing turn-on (triac or alternistor) also, this circuit includes a dv/dt snubber network connected across the power triac. this typical circuit illustrates switching the hot line; however, the load may be connected to either the hot or neutral line. also, note that the series gate resistor is low in value (22 ?) , which is possible on a 120 v line and above, since zero- crossing turn-on is ensured in any initial half cycle. summary of zero crossing turn-on circuits zero voltage crossing turn-on opto-drivers are designed to limit turn-on voltage to less than 20 v. this reduces the amount of rfi and emi generated when the thyristor switches on. because of this zero turn-on, these devices cannot be used to phase control loads. therefore, speed control of a motor and dimming of a lamp cannot be accomplished with zero turn-on opto-couplers. since the voltage is limited to 20 v or less, the series gate resis- tor that limits the gate drive current has to be much lower with a zero crossing opto-driver. with typical inhibit voltage of 5 v, an alternistor triac gate could require a 160 ma at -30 c (5 v/ 0.16 a = 31 ? gate resistor). if the load has a high inrush current, then drive the gate of the triac with as much current as reliably possible but stay under the i tsm rating of the opto-driver. by using 22 ? for the gate resistor, a current of at least 227 ma is supplied with only 5 v, but limited to 909 ma if the voltage goes to 20 v. as shown in figure an1007.12, figure an1007.13, and figure an1007.14, a 22 ? gate resistor is a good choice for various zero crossing controllers. figure an1007.12 zero crossing turn-on opto triac driver figure an1007.13 zero crossing turn-on non-sensitive scr driver figure an1007.14 zero crossing turn-on opto-sensitive gate scr driver r in v cc 1 120 v ac mt2 mt1 2 3 load 6 0.1 f 4 5 hot neutral zero crossing circuit g 100 22 triac or alternistor mt2 0.1 f 100 ? load mt1 hot neutral 120/240 v ac g 22 input r in 1 6 5 4 3 2 load could be here instead of lower location zero crossing circuit r in 1 g 120/240 v ac 2 3 0.1 f load 6 4 5 22 k a 100 g a k non-sensitive gate scrs load could be here instead of lower location zero crossing circuit input r in 1 g 120/240 v ac 2 3 0.1 f load 6 4 5 22 k a 100 g a k sensitive gate scrs load could be here instead of lower location zero crossing circuit input 1 k 1 k * * * gate diodes to have same piv as scrs
an1007 application notes http://www.teccor.com an1007 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog time delay relay circuit by combining a 555 timer ic with a triac, various time delays of several seconds can be achieved for delayed activation of solid state relays or switches. figure an1007.15 shows a solid state timer delay relay using a sensitive gate triac and a 555 timer ic. the 555 timer precisely controls time delay of operation using an external resistor and capacitor, as illustrated by the resistor and capacitor combination curves. (figure an1007.16) figure an1007.15 555 timer circuit with 10 second delay figure an1007.16 resistor (r) and capacitor (c) combination curves ir motion control an example of a more complex triac switch is an infrared (ir) motion detector controller circuit. some applications for this cir- cuit are alarm systems, automatic lighting, and auto doorbells. figure an1007.17 shows an easy- to-implement automatic light- ing system using an infrared motion detector control circuit. a commercially available lsi circuit ht761xb, from holtek, inte- grates most of the analog functions. this lsi chip, u2, contains the op amps, comparators, zero crossing detection, oscillators, and a triac output trigger. an external rc that is connected to the oscd pin determines the output trigger pulse width. ( holtek semiconductor inc. is located at no.3, creation road ii, science- based industrial park, hsinchu, taiwan, r.o.c.) device u1 pro- vides the infrared sensing. device r13 is a photo sensor that serves to prevent inadvertent triggering under daylight or other high light conditions. choosing the right triac depends on the load characteristics. for example, an incandescent lamp operating at 110 v requires a 200 v, 8 a triac. this gives sufficient margin to allow for the high current state during lamp burn out. u2 provides a minimum out- put triac negative gate trigger current of 40 ma, thus operating in qii & qiii. this meets the requirements of a 25 ma gate triac. teccor also offers alternistor triacs for inductive load conditions. this circuit has three operating modes (on, auto, off), which can be set through the mode pin. while the lsi chip is working in the auto mode, the user can override it and switch to the test mode, or manual on mode, or return to the auto mode by switch- ing the power switch. more information on this circuit, such as mask options for the infrared trigger pulse and flash options, are available in the holtek ht761x general purpose pir controller specifications. figure an1007.17 i r motion control circuit 555 10 k 0.1 f 0.01 f 1 f 1 k load mt2 mt1 g 10 m 1n4740 3.5 k 10 f + _ 1n4003 -10 v 250 v 120 v 60 hz 4 38 2 5 1 6 7 r c 10ms 100ms 1ms 10ms 100ms 1.0 10 100 0.001 0.01 0.1 1.0 10 100 t d time delay (s) c, (capacitance) (f) 1 k ? 1 0 k ? 1 0 0 k ? 1 m ? 1 0 m ? s g d u1 pir sd622 (nippon ceramic) 1 3 c4 100f 56k r3 2 c13 0.02f c12 22f r12 22k c9 10f c2 0.02f r4 1m c1 100f q1 triac q2008l4 ac lp1 lamp 60 to 600 watt c8 0.1f d3 1n4002 sw1 on/off override ac+ 110 r9 1m r7 1m r8 569k c3 100pf c7 3900pf u2 vss triac oscd oscs zc cds mode vdd op20 op2n op2p op10 op1n op1p rstb vee 1 2 3 4 5 6 7 8 ht761xb -16 dip/sop 9 10 11 12 13 14 15 16 r6 1m 0.02f c5 c6 22f r5 22k sw2 mode off auto on r2 2.4m d4 1n4002 *r10 d1 12v r13 cds c11 330f d2 1n4002 c10 0.33f 350v r14 68w 2w r9 1m d5 1n4002
?2002 teccor electronics an1008 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 8 explanation of maximum ratings and characteristics for thyristors introduction data sheets for scrs and triacs give vital information regarding maximum ratings and characteristics of thyristors. if the maxi- mum ratings of the thyristors are surpassed, possible irrevers- ible damage may occur. the characteristics describe various pertinent device parameters which are guaranteed as either min- imums or maximums. some of these characteristics relate to the ratings but are not ratings in themselves. the characteristic does not define what the circuit must provide or be restricted to, but defines the device characteristic. for example, a minimum value is indicated for the dv/dt because this value depicts the guaran- teed worst-case limit for all devices of the specific type. this min- imum dv/dt value represents the maximum limit that the circuit should allow. maximum ratings v rrm : peak repetitive reverse voltage ? scr the peak repetitive reverse voltage rating is the maximum peak reverse voltage that may be continuously applied to the main ter- minals (anode, cathode) of an scr. (figure an1008.1) an open- gate condition and gate resistance termination is designated for this rating. an increased reverse leakage can result due to a pos- itive gate bias during the reverse voltage exposure time of the scr. the repetitive peak reverse voltage rating relates to case temperatures up to the maximum rated junction temperature. figure an1008.1 v-i characteristics of scr device v drm : peak repetitive forward (off-state) voltage scr the peak repetitive forward (off-state) voltage rating (figure an1008.1) refers to the maximum peak forward voltage which may be applied continuously to the main terminals (anode, cath- ode) of an scr. this rating represents the maximum voltage the scr should be required to block in the forward direction. the scr may or may not go into conduction at voltages above the v drm rating. this rating is specified for an open-gate condition and gate resistance termination. a positive gate bias should be avoided since it will reduce the forward-voltage blocking capabil- ity. the peak repetitive forward (off-state) voltage rating applies for case temperatures up to the maximum rated junction temper- ature. triac the peak repetitive off-state voltage rating should not be sur- passed on a typical, non-transient, working basis. (figure an1008.2) v drm should not be exceeded even instantaneously. this rating applies for either positive or negative bias on main terminal 2 at the rated junction temperature. this voltage is less than the minimum breakover voltage so that breakover will not occur during operation. leakage current is controlled at this volt- age so that the temperature rise due to leakage power does not contribute significantly to the total temperature rise at rated cur- rent. figure an1008.2 v-i characteristics of triac device reverse breakdown voltage forward breakover voltage specified minimum off - state blocking voltage (v drm ) +i -i +v -v minimum holding current (i h ) voltage drop (v t ) at specified current (i t ) latching current (i l ) off - state leakage current - (i drm ) at specified v drm specified minimum reverse blocking voltage (v rrm ) reverse leakage current - (i rrm ) at specified v rrm breakover voltage specified minimum off-state blocking voltage (v drm ) +i -i +v -v minimum holding current (i h ) voltage drop (v t ) at specified current (i t ) latching current (i l ) off-state leakage current ? (i drm ) at specified v drm an1008
an1008 application notes http://www.teccor.com an1008 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog i t : current rating scr for rms and average currents, the restricting factor is usually confined so that the power dissipated during the on state and as a result of the junction-to-case thermal resistance will not pro- duce a junction temperature in excess of the maximum junction temperature rating. power dissipation is changed to rms and average current ratings for a 60 hz sine wave with a 180 con- duction angle. the average current for conduction angles less than 180 is derated because of the higher rms current con- nected with high peak currents. the dc current rating is higher than the average value for 180 conduction since no rms com- ponent is present. the dissipation for non-sinusoidal waveshapes can be deter- mined in several ways. graphically plotting instantaneous dissi- pation as a function of time is one method. the total maximum allowable power dissipation (p d ) may be determined using the following equation for temperature rise: where t j (max) is the maximum rated junction temperature (at zero rated current), t c is the actual operating case temperature, and r jc is the published junction-to-case thermal resistance. transient thermal resistance curves are required for short inter- val pulses. triac the limiting factor for rms current is determined by multiplying power dissipation by thermal resistance. the resulting current value will ensure an operating junction temperature within maxi- mum value. for convenience, dissipation is converted to rms current at a 360 conduction angle. the same rms current can be used at a conduction angle of less than 360. for information on non-sinusoidal waveshapes and a discussion of dissipation, refer to the preceding description of scr current rating. i tsm : peak surge (non-repetitive) on-state current ? scr and triac the peak surge current is the maximum peak current that may be applied to the device for one full cycle of conduction without device degradation. the maximum peak current is usually speci- fied as sinusoidal at 50 hz or 60 hz. this rating applies when the device is conducting rated current before the surge and, thus, with the junction temperature at rated values before the surge. the junction temperature will surpass the rated operating tem- perature during the surge, and the blocking capacity may be decreased until the device reverts to thermal equilibrium . the surge-current curve in figure an1008.3 illustrates the peak current that may be applied as a function of surge duration. this surge curve is not intended to depict an exponential current decay as a function of applied overload. instead, the peak current shown for a given number of cycles is the maximum peak surge permitted for that time period. the current must be derated so that the peak junction temperature during the surge overload does not exceed maximum rated junction temperature if blocking is to be retained after a surge. figure an1008.3 peak surge current versus surge current duration i tm : peak repetitive on-state current ? scr and triac the i tm rating specifies the maximum peak current that may be applied to the device during brief pulses. when the device oper- ates under these circumstances, blocking capability is main- tained. the minimum pulse duration and shape are defined and control the applied di/dt. the operating voltage, the duty factor, the case temperature, and the gate waveform are also defined. this rating must be followed when high repetitive peak currents are employed, such as in pulse modulators, capacitive-discharge circuits, and other applications where snubbers are required. di/dt: rate-of-change of on-sta te current ? scr and triac the di/dt rating specifies the maximum rate-of-rise of current through a thyristor device during turn-on. the value of principal voltage prior to turn-on and the magnitude and rise time of the gate trigger waveform during turn-on are among the conditions under which the rating applies. if the rate-of-change of current (di/dt) exceeds this maximum value, or if turn-on with high di/dt during minimum gate drive occurs (such as dv/dt or overvoltage events), then localized heating may cause device degradation. during the first few microseconds of initial turn-on, the effect of di/dt is more pronounced. the di/dt capability of the thyristor is greatly increased as soon as the total area of the pellet is in full conduction. the di/dt effects that can occur as a result of voltage or transient turn-on (non-gated) is not related to this rating. the di/dt rating is specified for maximum junction temperature. as shown in figure an1008.4, the di/dt of a surge current can be calculated by means of the following equation. as an example, surge current of 400 a at 60 hz has a di/dt of 400/8.3 or 151.4 a/ms. p d t jmax () t c ? r jc ----------------------------------- = 110 100 1000 10 20 30 40 50 60 80 100 120 150 250 300 400 1000 sur g e current duration ? full c y cles peak surge (non-repetitive) on-state current (i tsm ) ? amps 40 a to-218 25 a t0-220 15 a to-220 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. supply frequency: 60 hz sinusoidal load: resistive rms on-state current [ i t(rms)]: maximum rated value at specified case temperature notes: di dt ---- - i tm () t ----------------- - =
application notes an1008 ?2002 teccor electronics an1008 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1008.4 relationship of ma ximum current rating to time i 2 t rating ? scr and triac the i 2 t rating gives an indication of the energy-absorbing capabil- ity of the thyristor device during surge-overload conditions. the rating is the product of the square of the rms current (i rms ) 2 that flows through the device and the time during which the current is present and is expressed in a 2 s. this rating is given for fuse selection purposes. it is important that the i 2 t rating of the fuse is less than that of the thyristor device. without proper fuse or cur- rent limit, overload or surge current will permanently damage the device due to excessive junction heating. p g : gate power dissipation ? scr and triac gate power dissipation ratings define both the peak power (p gm ) forward or reverse and the average power (p g(av) ) that may be applied to the gate. damage to the gate can occur if these ratings are not observed. the width of the applied gate pulses must be considered in calculating the voltage and current allowed since the peak power allowed is a function of time. the peak power that results from a given signal source relies on the gate charac- teristics of the specific unit. the average power resulting from high peak powers must not exceed the average-power rating. t s , t j : temperature range ? scr and triac the maximum storage temperature (t s ) is greater than the maxi- mum operating temperature (actually maximum junction temper- ature). maximum storage temperature is restricted by material limits defined not so much by the silicon but by peripheral materi- als such as solders used on the chip/die and lead attachments as well as the encapsulating epoxy. the forward and off-state block- ing capability of the device determines the maximum junction (t j ) temperature. maximum blocking voltage and leakage current rat- ings are established at elevated temperatures near maximum junction temperature; therefore, operation in excess of these lim- its may result in unreliable operation of the thyristor. characteristics v bo : instantaneous breakover voltage ? scr and triac breakover voltage is the voltage at which a device turns on (switches to on state by voltage breakover). (figure an1008.1) this value applies for open-gate or gate-resistance termination. positive gate bias lowers the breakover voltage. breakover is temperature sensitive and will occur at a higher voltage if the junction temperature is kept below maximum t j value. if scrs and triacs are turned on as a result of an excess of breakover voltage, instantaneous power dissipations may be produced that can damage the chip or die. i drm : peak repetitive off-state (blocking) current scr i drm is the maximum leakage current permitted through the scr when the device is forward biased with rated positive voltage on the anode (dc or instantaneous) at rated junction temperature and with the gate open or gate resistance termination. a 1000 ? resistor connected between gate and cathode is required on all sensitive scrs. leakage current decreases with decreasing junction temperatures. effects of the off-state leakage currents on the load and other circuitry must be considered for each cir- cuit application. leakage currents can usually be ignored in applications that control high power. triac the description of peak off-state (blocking/leakage) current for the triac is the same as for the scr except that it applies with either positive or negative bias on main terminal 2. (figure an1008.2) i rrm : peak repetitive reverse current ? scr this characteristic is essentially the same as the peak forward off-state (blocking/leakage) current except negative voltage is applied to the anode (reverse biased). v tm : peak on-state voltage ? scr and triac the instantaneous on-state voltage (forward drop) is the principal voltage at a specified instantaneous current and case temperature when the thyristor is in the conducting state. to prevent heating of the junction, this characteristic is mea- sured with a short current pulse. the current pulse should be at least 100 s duration to ensure the device is in full conduc- tion. the forward-drop characteristic determines the on-state dissipation. see figure an1008.5, and refer to ?it: current rating? on page an1008-2. figure an1008.5 on-state current versus on-state voltage (typical) i i tm di/dt time 0t t = 8.3 ms for 60 hz 10 ms for 50 hz di dt (i tm ) t = 15 and 25 a to-220 t c = 25 ?c 40 a to-218 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 positive or negative instantaneous on-state voltage (v t ) ? volts 0 10 20 30 40 50 60 70 80 90 positive or negative instantaneous on-state current (i t ) ? amps
an1008 application notes http://www.teccor.com an1008 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog i gt : dc gate trigger current scr i gt is the minimum dc gate current required to cause the thyris- tor to switch from the non-conducting to the conducting state for a specified load voltage and current as well as case temperature. the characteristic curve illustrated in figure an1008.6 shows that trigger current is temperature dependent. the thyristor becomes less sensitive (requires more gate current) with decreasing junction temperatures. the gate current should be increased by a factor of two to five times the minimum threshold dc trigger current for best operation. where fast turn-on is demanded and high di/dt is present or low temperatures are expected, the gate pulse may be 10 times the minimum i gt , plus it must be fast-rising and of sufficient duration in order to properly turn on the thyristor. figure an1008.6 normalized dc gate trigger current for all quadrants versus case temperature triac the description for the scr applies as well to the triac with the addition that the triac can be fired in four possible modes (figure an1008.7): quadrant i (main terminal 2 positive, gate positive) quadrant ii (main terminal 2 positive, gate negative) quadrant iii (main terminal 2 negative, gate negative) quadrant iv (main terminal 2 negative, gate positive) figure an1008.7 definition of operating quadrants v gt : dc gate trigger voltage scr v gt is the dc gate-cathode voltage that is present just prior to triggering when the gate current equals the dc trigger current. as shown in the characteristic curve in figure an1008.8, the gate trigger voltage is higher at lower temperatures. the gate-cathode voltage drop can be higher than the dc trigger level if the gate is driven by a current higher than the trigger current. triac the difference in v gt for the scr and the triac is that the triac can be fired in four possible modes. the threshold trigger voltage can be slightly different, depending on which of the four operating modes is actually used. figure an1008.8 normalized dc gate trigger voltage for all quadrants versus case temperature i l : latching current scr latching current is the dc anode current above which the gate signal can be withdrawn and the device stays on. it is related to, has the same temperature dependence as, and is somewhat greater than the dc gate trigger current. (figure an1008.1 and figure an1008.2) latching current is at least equal to or much greater than the holding current, depending on the thyristor type. latching current is greater for fast-rise-time anode currents since not all of the chip/die is in conduction. it is this dynamic latching current that determines whether a device will stay on when the gate signal is replaced with very short gate pulses. the dynamic latching current varies with the magnitude of the gate drive cur- rent and pulse duration. in some circuits, the anode current may oscillate and drop back below the holding level or may even go negative; hence, the unit may turn off and not latch if the gate sig- nal is removed too quickly. triac the description of this characteristic for the triac is the same as for the scr, with the addition that the triac can be latched on in four possible modes (quadrants). also, the required latching is significantly different depending on which gating quadrants are used. figure an1008.9 illustrates typical latching current require- ments for the four possible quadrants of operation. 0 1.0 2.0 3.0 4.0 -65 -15 +65 +25 +125 -40 case temperature (t c ) ? ?c ratio of i gt i gt (t c = 25 ?c) mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - note: alternistors will not operate in q iv 0 .5 1.0 1.5 2.0 -65 -15 +65 +25 +125 -40 case temperature (t c ) ? ?c v gt (t c = 25 ?c) ratio of v gt
application notes an1008 ?2002 teccor electronics an1008 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1008.9 typical triac latching (i l ) requirements for four quadrants versus gate current (i gt ) i h : holding current ? scr and triac the holding current is the dc principal on-state current below which the device will not stay in regeneration/on state after latch- ing and gate signal is removed. this current is equal to or lower in value than the latching current (figure an1008.1 and figure an1008.2) and is related to and has the same temperature dependence as the dc gate trigger current shown in figure an1008.10. both minimum and maximum holding current may be important. if the device is to stay in conduction at low-anode cur- rents, the maximum holding current of a device for a given circuit must be considered. the minimum holding current of a device must be considered if the device is expected to turn off at a low dc anode current. note that the low dc principal current condi- tion is a dc turn-off mode, and that an initial on-state current (latching current) is required to ensure that the thyristor has been fully turned on prior to a holding current measurement. figure an1008.10 normalized dc holding current versus case temperature dv/dt, static: critical rate-of-rise of off-state voltage ? scr and triac static dv/dt is the minimum rate-of-rise of off-state voltage that a device will hold off, with gate open, without turning on. figure an1008.11 illustrates the exponential definition. this value will be reduced by a positive gate signal. this charac- teristic is temperature-dependent and is lowest at the maxi- mum-rated junction temperature. therefore, the characteristic is determined at rated junction temperature and at rated forward off-state voltage which is also a worst-case situation. line or other transients which might be applied to the thyristor in the off state must be reduced, so that neither the rate-of- rise nor the peak voltage are above specifications if false firing is to be prevented. turn-on as result of dv/dt is non-destructive as long as the follow current remains within current ratings of the device being used. figure an1008.11 exponential rate-of-rise of off-state voltage defining dv/dt dv/dt, commutating: critical rate-of-rise of commutation voltage ? triac commutating dv/dt is the rate-of-rise of voltage across the main terminals that a triac can support (block without switching back on) when commutating from the on state in one half cycle to the off state in the opposite half cycle. this parameter is specified at maximum rated case temperature (equal to t j ) since it is temper- ature-dependent. it is also dependent on current (commutating di/dt) and peak reapplied voltage (line voltage) and is specified at rated current and voltage. all devices are guaranteed to commu- tate rated current with a resistive load at 50 hz to 60 hz. com- mutation of rated current is not guaranteed at higher frequencies, and no direct relationship can be made with regard to current/ temperature derating for higher-frequency operation. with induc- tive loading, when the voltage is out of phase with the load cur- rent, a voltage stress (dv/dt) occurs across the main terminals of the triac during the zero-current crossing. (figure an1008.12) a snubber (series rc across the triac) should be used with induc- tive loads to decrease the applied dv/dt to an amount below the minimum value which the triac can be guaranteed to commutate off each half cycle. ii iii iv i 0 1.0 2.0 3.0 4.0 5.0 6.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 i l ? ma i gt ? ma 0 1.0 2.0 3.0 4.0 -65 -15 +65 +25 +125 -40 case temperature (t c ) ? ?c i h (t c = 25 ?c) ratio of i h initial on - state current = 400 ma dc critical dv/dt dv = 0.63 v d t t = rc 0 dt t 63% of v d v d
an1008 application notes http://www.teccor.com an1008 - 6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog commutating dv/dt is specified for a half sinewave current at 60 hz which fixes the di/dt of the commutating current. the com- mutating di/dt for 50 hz is approximately 20% lower while i rms rating remains the same. (figure an1008.4) figure an1008.12 waveshapes of commutating dv/dt and associated conditions t gt : gate-controlled turn-on time ? scr and triac the t gt is the time interval between the application of a gate pulse and the on-state current reaching 90% of its steady-state value. (figure an1008.13) as would be expected, turn-on time is a function of gate drive. shorter turn-on times occur for increased gate drives. this turn-on time is actually only valid for resistive loading. for example, inductive loading would restrict the rate-of- rise of anode current. for this reason, this parameter does not indicate the time that must be allowed for the device to stay on if the gate signal is removed. (refer to the description of ?il: latch- ing current? on page an1008-4.) however, if the load was resis- tive and equal to the rated load current value, the device definitely would be operating at a current above the dynamic latching current in the turn-on time interval since current through the device is at 90% of its peak value during this interval. figure an1008.13 waveshapes for turn-on time and associated conditions t q : circuit-commutated turn-off time ? scr the circuit-commutated turn-off time of the device is the time dur- ing which the circuit provides reverse bias to the device (negative anode) to commutate it off. the turn-off time occurs between the time when the anode current goes negative and when the anode positive voltage may be reapplied. (figure an1008.14) turn-off time is a function of many parameters and very dependent on temperature and gate bias during the turn-off interval. turn-off time is lengthened for higher temperature so a high junction tem- perature is specified. the gate is open during the turn-off interval. positive bias on the gate will lengthen the turn-off time; negative bias on the gate will shorten it. figure an1008.14 waveshapes of t q rating test and associated conditions r jc , r ja : thermal resistance (junction-to-case, junction-to-ambient) ? scr and triac the thermal-resistance characteristic defines the steady-state temperature difference between two points at a given rate of heat-energy transfer (dissipation) between the points. the ther- mal-resistance system is an analog to an electrical circuit where thermal resistance is equivalent to electrical resistance, tempera- ture difference is equivalent to voltage difference, and rate of heat-energy transfer (dissipation) is equivalent to current. dissi- pation is represented by a constant current generator since gen- erated heat must flow (steady-state) no matter what the resistance in its path. junction-to-case thermal resistance estab- lishes the maximum case temperature at maximum rated steady- state current. the case temperature must be held to the maxi- mum at maximum ambient temperature when the device is oper- ating at rated current. junction-to-ambient thermal resistance is established at a lower steady-state current, where the device is in free air with only the external heat sinking offered by the device package itself. for r ja , power dissipation is limited by what the device package can dissipate in free air without any additional heat sink: i g i t time di/dt (di/dt) c c e m 10% 63% v drm (dv/dt) voltage across triac e source i trm 90% 90% 10% 50% 50% 10% on-state current rise time gate trigger pulse delay time turn-on time gate pulse width off-state voltage 10% i tm 50% i tm 50% i rm i r reverse current i d off-state leakage v d off-state voltage di/dt dv/dt t rr t q t 1 v t r jc t j t c ? p av () --------------------- = r ja t j t a ? p av ()
?2002 teccor electronics an1009 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 9 miscellaneous design tips and facts introduction this application note presents design tips and facts on the follow- ing topics: ? relationship of i av , i rms , and i pk ? dv/dt definitions ? examples of gate terminations ? curves for average current at various conduction angles ? double-exponential impulse waveform ? failure modes of thyristor ? characteristics formulas for phase control circuits relationship of i av , i rms , and i pk since a single rectifier or scr passes current in one direction only, it conducts for only half of each cycle of an ac sinewave. the average current (i av ) then becomes half of the value deter- mined for full-cycle conduction, and the rms current (i rms ) is equal to the square root of half the mean-square value for full- cycle conduction or half the peak current (i pk ). in terms of half- cycle sinewave conduction (as in a single-phase half-wave cir- cuit), the relationships of the rectifier currents can be shown as follows: i pk = i av = 3.14 i av i av = (1 / ) i pk = 0.32 i pk i pk = 2 i rms i rms = 0.5 i pk i av = (2 / ) i rms = 0.64 i rms i rms = ( /2) i av = 1.57 i av when two identically rated scrs are connected inverse parallel for full-wave operation, as shown in figure an1009.1, they can handle 1.41 times the rms current rating of either single scr. therefore, the rms value of two half sinewave current pulses in one cycle is 2 times the rms value of one such pulse per cycle. figure an1009.1 scr anti-parallel circuit dv/dt definitions the rate-of-rise of voltage (dv/dt) of an exponential waveform is 63% of peak voltage (excluding any overshoots) divided by the time at 63% minus 10% peak voltage. (figure an1009.2) exponential dv/dt = = resistor capacitor circuit t = rc = resistor capacitor circuit figure an1009.2 exponential dv/dt waveform the rate-of-rise of voltage (dv/dt) of a linear waveform is 80% of peak voltage (excluding any overshoots) divided by the time at 90% minus 10% peak voltage. (figure an1009.3) linear dv/dt = = linear dv/dt = = figure an1009.3 linear dv/dt waveform 0.63 v pk [] ? t 2 t 1 ? () t 2 t 1 ? () 4rc ? t 3 t 2 ? () = (peak value) 100% 0% 63% t 1 t 2 t 0 t 3 percent of voltage time numerical dv/dt 10% 0.8 v pk [] ? t 2 t 1 ? () 0.9 v pk ? 0.1 v pk ? ? [] t 2 t 1 ? () 90% 0% 10% t 1 t 2 t 0 percent of voltage time an1009
an1009 application notes http://www.teccor.com an1009 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog examples of gate terminations primary purpose (1) increase dv/dt capability (2) keep gate clamped to ensure v drm capability (3) lower t q time related effect ? raises the device latching and holding current primary purpose (1) increase dv/dt capability (2) remove high frequency noise related effects (1) increases delay time (2) increases turn-on interval (3) lowers gate signal rise time (4) lowers di/dt capability (5) increases t q time primary purpose (1) decrease dc gate sensitivity (2) decrease t q time related effects (1) negative gate current increases holding current and causes gate area to drop out of conduction (2) in pulse gating gate signal tail may cause device to drop out of conduction primary purpose ? select frequency related effects ? unless circuit is ?damped,? positive and negative gate current may inhibit conduction or bring about spo- radic anode current primary purpose (1) supply reverse bias in off period (2) protect gate and gate supply for reverse transients (3) lower t q time related effects ? isolates the gate if high impedance signal source is used without sustained diode current in the negative cycle primary purpose ? decrease threshold sensitivity related effects (1) affects gate signal rise time and di/dt rating (2) isolates the gate primary purpose ? isolate gate circuit dc component related effects ? in narrow gate pulses and low impedance sources, i gt followed by reverse gate signals which may inhibit con- duction curves for average current at various conduction angles scr maximum average current curves for various conduction angles can be established using the factors for maximum aver- age current at conduction angle of: 30 = 0.40 x avg 180 60 = 0.56 x avg 180 90 = 0.70 x avg 180 120 = 0.84 x avg 180 the reason for different ratings is that the average current for conduction angles less than 180 is derated because of the higher rms current connected with high peak currents. note that maximum allowable case temperature (t c ) remains the same for each conduction angle curve but is established from average current rating at 180 conduction as given in the data sheet for any particular device type. the maximum t c curve is then derated down to the maximum junction (t j ). the curves illustrated in figure an1009.4 are derated to 125 c since the maximum t j for the non-sensitive scr series is 125 c. figure an1009.4 typical curves for average on-state current at various conduction angles versus t c for a sxx20l scr zener optional ? 80 85 90 95 100 105 110 115 120 125 0246810121416 average on-state current [i t (av)] ? amps maximum allowable case temperature (t c ) ? ? c 180 ? 90 ? 30 ? 60 ? 120 ? current: halfwave sinusoidal load: resistive or inductive conduction angle: as given below case temperature: measured as shown on dimensional drawings conduction angle 7.2 10.8 12.8 5.1
application notes an1009 ?2002 teccor electronics an1009 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 double-exponential impulse waveform a double-exponential impulse waveform or waveshape of current or voltage is designated by a combination of two numbers (t r /t d or t r x t d s). the first number is an exponential rise time (t r ) or wave front and the second number is an exponential decay time (t d ) or wave tail. the rise time (t r ) is the maximum rise time permitted. the decay time (t d ) is the minimum time permitted. both the t r and the t d are in the same units of time, typically microseconds, des- ignated at the end of the waveform description as defined by ansi/ieee c62.1-1989. the rise time (t r ) of a current waveform is 1.25 times the time for the current to increase from 10% to 90% of peak value. see fig- ure an1009.5. t r = rise time = 1.25 ? [t c ? t a ] t r = 1.25 ? [t(0.9 i pk ) ? t(0.1 i pk )] = t 1 ? t 0 the rise time (t r ) of a voltage waveform is 1.67 times the time for the voltage to increase from 30% to 90% of peak value. (figure an1009.5) t r = rise time = 1.67 ? [t c ? t b ] t r = 1.67 ? [t(0.9 v pk ) ? t(0.3 v pk )] = t 1 ? t 0 the decay time (t d ) of a waveform is the time from virtual zero (10% of peak for current or 30% of peak for voltage) to the time at which one-half (50%) of the peak value is reached on the wave tail. (figure an1009.5) current waveform t d = decay time = [t(0.5 i pk ) ? t(0.1 i pk )] = t 2 ? t 0 voltage waveform t d = decay time = [t(0.5 v pk ) ? t(0.3 v pk )] = t 2 ? t 0 figure an1009.5 double-exponential impulse waveform failure modes of thyristor thyristor failures may be broadly classified as either degrading or catastrophic. a degrading type of failure is defined as a change in some characteristic which may or may not cause a cat- astrophic failure, but could show up as a latent failure. cata- strophic failure is when a device exhibits a sudden change in characteristic that renders it inoperable. to minimize degrading and catastrophic failures, devices must be operated within maxi- mum ratings at all times. degradation failures a significant change of on-state, gate, or switching characteris- tics is quite rare. the most vulnerable characteristic is blocking voltage. this type of degradation increases with rising operating voltage and temperature levels. catastrophic failures a catastrophic failure can occur whenever the thyristor is oper- ated beyond its published ratings. the most common failure mode is an electrical short between the main terminals, although a triac can fail in a half-wave condition. it is possible, but not probable, that the resulting short-circuit current could melt the internal parts of the device which could result in an open circuit. failure causes most thyristor failures occur due to exceeding the maximum operating ratings of the device. overvoltage or overcurrent oper- ations are the most probable cause for failure. overvoltage fail- ures may be due to excessive voltage transients or may also occur if inadequate cooling allows the operating temperature to rise above the maximum allowable junction temperature. over- current failures are generally caused by improper fusing or circuit protection, surge current from load initiation, load abuse, or load failure. another common cause of device failure is incorrect han- dling procedures used in the manufacturing process. mechanical damage in the form of excessive mounting torque and/or force applied to the terminals or leads can transmit stresses to the internal thyristor chip and cause cracks in the chip which may not show up until the device is thermally cycled. prevention of failures careful selection of the correct device for the application?s oper- ating parameters and environment will go a long way toward extending the operating life of the thyristor. good design practice should also limit the maximum current through the main terminals to 75% of the device rating. correct mounting and forming of the leads also help ensure against infant mortality and latent failures. the two best ways to ensure long life of a thyristor is by proper heat sink methods and correct voltage rating selection for worst case conditions. overheating, overvoltage, and surge currents are the main killers of semiconductors. most common thyristor failure mode when a thyristor is electrically or physically abused and fails either by degradation or a catastrophic means, it will short (full-wave or half-wave) as its normal failure mode. rarely does it fail open circuit. the circuit designer should add line breaks, fuses, over- temperature interrupters or whatever is necessary to protect the end user and property if a shorted or partially shorted thyristor offers a safety hazard. virtual start of wavefront (peak value) 100% 90% 50% 0% 10% 30% t a t b t 0 t c t 1 t 2 time percent of current or voltage decay = e - t 1.44 t 2
an1009 application notes http://www.teccor.com an1009 - 4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog characteristics formulas for phase control circuits note: angle alpha ( ) is in radians. half-wave resistive load ? schematic full-wave bridge ? schematic full-wave ac switch resistive load ? schematic half-wave resistive load ? waveform full-wave bridge ? waveform full-wave ac switch resistive load ? waveform circuit name max thyristor voltage prv max. load voltage e d =avg. e a =rms load voltage with delayed firing max. average thyristor or rectifier current scr avg. amps cond. period half-wave resistive load 1.4 e rms e p 180 full-wave bridge 1.4 e rms e p 180 full-wave ac switch resistive load 1.4 e rms e p 180 e d e p ------- = e a e p 2 ------- = e d e p 2 ------- 1 cos + () = e a e p 2 ---------- - ? 1 2 -- -2 sin + = e p r ------- - e d 2e p ---------- - =e d e p 2 ---------- -1 cos + () = e p r ------- - e a e p 1.4 ------- - =e a e p 2 ---------- - ? 1 2 -- -2 sin + = e p r ------- - e rms load r e load r l e rms load r 0 e p 0 e p 0 e p
?2002 teccor electronics an1010 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 10 thyristors for ignition of fluorescent lamps introduction one of the many applications for teccor thyristors is in fluores- cent lighting. standard conventional and circular fluorescent lamps with filaments can be ignited easily and much more quickly by using thyristors instead of the mechanical starter switch, and solid state thyristors are more reliable. thyristors produce a pure solid state igniting circuit with no mechanical parts in the fluores- cent lamp fixture. also, because the lamp ignites much faster, the life of the fluorescent lamp can be increased since the filaments are activated for less time during the ignition. the thyristor igni- tion eliminates any audible noise or flashing off and on which most mechanical starters possess. standard fluorescent circuit the standard starter assembly is a glow switch mechanism with option small capacitor in parallel. (figure an1010.1) figure an1010.1 typical standard fluorescent circuit the glow switch is made in a small glass bulb containing neon or argon gas. inside the bulb is a u-shaped bimetallic strip and a fixed post. when the line input current is applied, the voltage between the bimetallic strip and the fixed post is high enough to ionize and produce a glow similar to a standard neon lamp. the heat from the ionization causes the bimetallic strip to move and make contact to the fixed post. at this time the ionization ceases and current can flow through and pre-heat the filaments of the fluorescent lamp. since ionization (glowing) has ceased, the bimetallic strip begins to cool down and in a few seconds opens to start ionization (glowing) again. the instant the bimetallic ceases to make con- tact (opens), an inductive kick from the ballast produces some high voltage spikes 400 v to 600 v, which can ignite (strike) the fluorescent lamp. if the lamp fails to ignite or start, the glow switch mechanically repeats its igniting cycle over and over until the lamp ignites, usually within a few seconds. in this concept the ballast (inductor) is able to produce high volt- age spikes using a mechanical switch opening and closing, which is fairly slow. since thyristors (solid state switches) do not mechanically open and close, the conventional fluorescent lighting circuit concept must be changed in order to use thyristors. in order to ignite (strike) a fluorescent lamp, a high voltage spike must be pro- duced. the spike needs to be several hundred volts to quickly ini- tiate ionization in the fluorescent lamp. a series ballast can only produce high voltage if a mechanical switch is used in conjunc- tion with it. therefore, with a thyristor a standard series ballast (inductor) is only useful as a current limiter. methods for producing high voltage the circuits illustrated in figure an1010.2 through figure an1010.5 show various methods for producing high voltage to ignite fluorescent lamps using thyristors (solid state switches). note: due to many considerations in designing a fluorescent fix- ture, the illustrated circuits are not necessarily the optimum design. one 120 v ac circuit consists of triac and diac thyristors with a capacitor to ignite the fluorescent lamp. (figure an1010.2) this circuit allows the 5 f ac capacitor to be charged and added to the peak line voltage, developing close to 300 v peak or 600 v peak to peak. this is accomplished by using a triac and diac phase control network set to fire near the 90 point of the input line. a capacitor-charging network is added to ensure that the capacitor is charged immediately, letting tolerances of compo- nents or temperature changes in the triac and diac circuit to be less critical. by setting the triac and diac phase control to fire at near the 90 point of the sinewave, maximum line voltages appear across the lamp for ignition. as the triac turns on during each half cycle, the filaments are pre-heated and in less than a second the lamp is lit. once the lamp is lit the voltage is clamped to approximately 60 v peak across the 15 w to 20 w lamp, and the triac and diac circuit no longer functions until the lamp is required to be ignited again. line input lamp starter assembly ballast an1010
an1010 application notes http://www.teccor.com an1010 - 2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog figure an1010.2 120 v ac triac/diac circuit figure an1010.3 illustrates a circuit using a sidac (a simpler thy- ristor) phase control network to ignite a 120 v ac fluorescent lamp. as in the triac/diac circuit, the 5 f ac capacitor is charged and added to the peak line voltage, developing greater than 200 v peak or 400 v peak to peak. since the sidac is a voltage breakover (v bo ) activated device with no gate, a charging net- work is essential in this circuit to charge the capacitor above the peak of the line in order to break over (turn on) the sidac with a v bo of 220 v to 250 v. as the sidac turns on each half cycle, the filaments are pre- heated and in less than 1.5 seconds the lamp is lit. once the lamp is lit, the voltage across it clamps to approximately 60 v peak (for a 15 w to 20 w lamp), and the sidac ceases to function until the lamp is required to be ignited again. figure an1010.3 120 v ac sidac circuit the circuits illustrated in figure an1010.2 and figure an1010.3 use 15 w to 20 w lamps. the same basic circuits can be applied to higher wattage lamps. however, with higher wattage lamps the voltage developed to fire (light) the lamp will need to be some- what higher. for instance, a 40 w lamp is critical on line input voltage to ignite, and after it is lit the voltage across the lamp will clamp to approximately 130 v peak. for a given type of lamp, the current must be limited to constant current regardless of the watt- age of the lamp. figure an1010.4 shows a circuit for igniting a fluorescent lamp with 240 v line voltage input using triac and diac networks. 120 v ac line input lamp 15 w - 20 w optional charging network 5 f 400 v 0.047 f 50 v 220 k ht-32 mt1 g mt2 q401e4 ballast 14 w - 22 w 1n4004 47 k 120 v ac line input lamp 15 w - 20w k2400e sidac optional charging network 5 f 400 v ballast 14 w - 22w 1n4004 47 k
application notes an1010 ?2002 teccor electronics an1010 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure an1010.4 240 v ac triac/diac circuit figure an1010.5 illustrates a circuit using a sidac phase control network to ignite a 240 v ac fluorescent lamp. this circuit works basically the same as the 120 v circuit shown in figure an1010.3, except that component values are changed to com- pensate for higher voltage. the one major change is that two k2400e devices in series are used to accomplish high firing volt- age for a fluorescent lamp. figure an1010.5 240 v ac sidac circuit 240 v ac line input lamp 40 w optional charging network 3.3 f 0.047 f 50 v 470 k ht-32 mt1 g mt2 q601e4 ballast 47 k 1n4004 lamp 40 w 3.3 f 240 v ac line input k2400e sidac k2400e sidac optional charging network ballast 1n4004 47 k
notes
?2002 teccor electronics a-1 http://www.teccor.com thyristor product catalog +1 972-580-7777 cross reference guide triacs, scrs, diacs, sidacs, and rectifiers (suggested teccor replacements for jedec and industry house numbers) 1 how to use this guide this cross reference guide will help you determine the compet- itive products that teccor supplies on either a direct replacement or suggested replacement basis. teccor offers replacements for most competitive devices. if you do not find a desired competitive product type listed, please con- tact the factory for information on recent additions to this list. on the following pages, listed in alphanumeric order, you will find: ? competitive product number ? teccor device part number ? ?d? indicating the direct replacement (teccor device meets or exceeds the electrical and mechanical specifications of the competitive device); ?s? indicates a suggested replacement (the suggested replacements in this guide represent the nearest teccor equivalent for the product listed and in most instances are replacements. however, teccor assumes no responsibility and does not guarantee that the replacements are exact; only that the replacements will meet the terms of its applicable published written specifications. the pertinent teccor specification sheet should be used as the principle tool for actual replacements.) ? teccor package type for additional assistance, contact your nearest teccor distributor, sales representative, or the factory.
cross reference guide appendix http://www.teccor.com a-2 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog part number teccor device direct or suggested replacement teccor package 40431 q2006lt s to-220 (isol) 03p05m ec103b s to-92 (isol) 03p1m ec103b s to-92 (isol) 03p2m ec103b s to-92 (isol) 03p3m ec103d s to-92 (isol) 03p4m ec103d s to-92 (isol) 03p5m ec103m s to-92 (isol) 10tts08s s8012d s to-252 (smdt) 16tts08 s8016r d to-220 (n.isol) 16tts08s s8016n s to-263 (smt) 25tts08 s8025r d to-220 (n.isol) 25tts08fp s8025l d to-220 (isol) 25tts08s s8025n s to-263 (smt) 2n1595 s201e s to-92 (isol) 2n1596 s201e s to-92 (isol) 2n1597 s201e s to-92 (isol) 2n1598 s401e s to-92 (isol) 2n1599 s401e s to-92 (isol) 2n2323 tcr22-4 75 s to-92 (isol) 2n3001 ec103b s to-92 (isol) 2n3002 ec103b s to-92 (isol) 2n3003 ec103b s to-92 (isol) 2n3004 ec103b s to-92 (isol) 2n3005 ec103b d to-92 (isol) 2n3006 ec103b d to-92 (isol) 2n3007 ec103b d to-92 (isol) 2n3008 ec103b d to-92 (isol) 2n3228 s2006r s to-220 (n.isol) 2n3525 s4006r s to-220 (n.isol) 2n3528 s2006f1 s to-202 (n.isol) 2n3529 s4006f1 s to-202 (n.isol) 2n4101 s6006l s to-220 (isol) 2n4102 s6006f1 s to-202 (n.isol) 2n4441 s2008r s to-220 (n.isol 2n4442 s2008r s to-220 (n.isol) 2n4443 s4008r s to-220 (n.isol) 2n4444 s6008r s to-220 (n.isol) 2n5060 2n5064 d to-92 (isol) 2n5061 2n5064 d to-92 (isol) 2n5062 2n5064 d to-92 (isol) 2n5063 2n5064 d to-92 (isol) 2n5064 2n5064 d to-92 (isol) 2n5754 q2004f41 s to-202 (n.isol) 2n5755 q2004f41 s to-202 (n.isol) 2n5756 q4004f41 s to-202 (n.isol) 2n6068 q2004f41 s to-202 (n.isol) 2n6068a l2004f51 s to-202 (n.isol) 2n6068b l2004f31 s to-202 (n.isol) 2n6069 q2004f41 s to-202 (n.isol) 2n6069a l2004f51 s to-202 (n.isol) 2n6069b l2004f31 s to-202 (n.isol) 2n6070 q2004f41 s to-202 (n.isol) 2n6070a l2004f51 s to-202 (n.isol) 2n6070b l2004f31 s to-202 (n.isol) 2n6071 q2004f41 s to-202 (n.isol) 2n6071a l2004f51 s to-202 (n.isol) 2n6071b l2004f31 s to-202 (n.isol) 2n6072 q4004f41 s to-202 (n.isol) 2n6072a l4004f51 s to-202 (n.isol) 2n6072b l4004f31 s to-202 (n.isol) 2n6073 q4004f41 s to-202 (n.isol) 2n6073a l4004f51 s to-202 (n.isol) 2n6073b l4004f31 s to-202 (n.isol) 2n6074 q6004f41 s to-202 (n.isol) 2n6074a l6004f51 s to-202 (n.isol) 2n6074b l6004f31 s to-202 (n.isol) 2n6075 q6004f41 s to-202 (n.isol) 2n6075a l6004f51 s to-202 (n.isol) 2n6075b l6004f31 s to-202 (n.isol) 2n6236 t106b1 s to-202 (n.isol) 2n6237 t106b1 s to-202 (n.isol) 2n6238 t106b1 s to-202 (n.isol) 2n6239 t106b1 s to-202 (n.isol) 2n6240 t106d1 s to-202 (n.isol) 2n6241 t106m1 s to-202 (n.isol) 2n6342 q2008r4 s to-220 (n.isol) 2n6342a q2012rh5 s to-220 (n.isol) 2n6343 q4008r4 s to-220 (n.isol) 2n6343a q4012rh5 s to-220 (n.isol) 2n6344 q6008r5 s to-220 (n.isol) 2n6344a q6012rh5 s to-220 (n.isol) 2n6345 q8008r5 s to-220 (n.isol) 2n6345a q8012rh5 s to-220 (n.isol) 2n6346a q2015r5 s to-220 (n.isol) 2n6347a q4015r5 s to-220 (n.isol) 2n6348a q6015r5 s to-220 (n.isol) 2n6349 q8010r5 s to-220 (n.isol) 2n6349a q8015r5 s to-220 (n.isol) 2n6394 s2012r d to-220 (n.isol) 2n6395 s2012r d to-220 (n.isol) 2n6396 s2012r d to-220 (n.isol) 2n6397 s4012r d to-220 (n.isol) 2n6398 s6012r d to-220 (n.isol) 2n6399 s8012r d to-220 (n.isol) 2n6400 s2016r d to-220 (n.isol) 2n6401 s2016r d to-220 (n.isol) 2n6402 s2016r d to-220 (n.isol) 2n6403 s4016r d to-220 (n.isol) 2n6404 s6016r d to-220 (n.isol) 2n6405 s8016r d to-220 (n.isol) 2n6504 s2025r d to-220 (n.isol) 2n6505 s2025r d to-220 (n.isol) 2n6506 s2025r d to-220 (n.isol) 2n6507 s4025r d to-220 (n.isol) 2n6508 s6025r d to-220 (n.isol) 2n6509 s8025r d to-220 (n.isol) 2n6564 2n6565 d to-92 (isol) 2n6564 ec103d s to-92 (isol) 2n6565 2n6565 d to-92 (isol) 2n6565 ec103d s to-92 (isol) 2n877 ec103b s to-92 (isol) 2n878 ec103b s to-92 (isol) 2n879 ec103b s to-92 (isol) 2n880 ec103b s to-92 (isol) 2n881 ec103b s to-92 (isol) 2n885 2n5064 d to-92 (isol) 2n886 2n5064 d to-92 (isol) 2n887 2n5064 d to-92 (isol) 2n888 2n5064 d to-92 (isol) 2n889 2n5064 d to-92 (isol) 2p05m t106b1 s to-202 (n.isol) 2p1m t106b1 s to-202 (n.isol) 2p2m t106b1 s to-202 (n.isol) 2p4m t106d1 s to-202 (n.isol) 2p5m t106m1 s to-202 (n.isol) 2p6m t106m1 s to-202 (n.isol) 30tps08 s8035k s to-218ac (isol) "k" 3p4j t106d2 s to-202 (n.isol) 40tps08 s8035k s to-218ac (isol) "k" 5p05m s2008r s to-220 (n.isol) 5p1m s2008r s to-220 (n.isol) 5p2m s2008r s to-220 (n.isol) 5p4m s4008r s to-220 (n.isol) 5p5m s6008r s to-220 (n.isol) 5p6m s6008r s to-220 (n.isol) 8t04ha q2004f41 d to-202 (n.isol) 8t04sh l2004f81 s to-202 (n.isol) 8t14ha q2004f41 d to-202 (n.isol) 8t14sh l2004f81 s to-202 (n.isol) 8t24ha q2004f41 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-3 http://www.teccor.com thyristor product catalog +1 972-580-7777 8t24sh l2004f81 s to-202 (n.isol) 8t34ha q4004f41 d to-202 (n.isol) 8t34sh l4004f81 s to-202 (n.isol) 8t44ha q4004f41 d to-202 (n.isol) 8t44sh l4004f81 s to-202 (n.isol) 8t54ha q6004f41 d to-202 (n.isol) 8t64ha q6004f41 d to-202 (n.isol) 8t64sh l6004f81 s to-202 (n.isol) ac03bgm q2004f41 s to-202 (n.isol) ac03dgm q4004f41 s to-202 (n.isol) ac03egm q5004f41 s to-202 (n.isol) ac03fgm q6004f41 s to-202 (n.isol) ac08bgm q2008r5 s to-220 (n.isol) ac08bsm q2008lh4 s to-220 (isol) ac08dgm q4008r4 s to-220 (n.isol) ac08dsm q4008lh4 s to-220 (isol) ac08egm q6008r4 s to-220 (n.isol) ac08esm q6008lh4 s to-220 (isol) ac08fgm q6008r5 s to-220 (n.isol) ac08fsm q6008lh4 s to-220 (isol) ac10bgml q2010rh5 s to-220 (n.isol) ac10bsm q2010lh5 s to-220 (isol) ac10dgml q4010rh5 s to-220 (n.isol) ac10dsm q4010lh5 s to-220 (isol) ac10egml q6010rh5 s to-220 (n.isol) ac10esm q6010lh5 s to-220 (isol) ac10fgml q6010rh5 s to-220 (n.isol) ac10fsm q6010lh5 s to-220 (isol) ac12bgml q2012rh5 s to-220 (n.isol) ac12bsm q2012lh5 s to-220 (isol) ac12dgml q4012rh5 s to-220 (n.isol) ac12dsm q4012lh5 s to-220 (isol) ac12egml q6012rh5 s to-220 (n.isol) ac12esm q6012lh5 s to-220 (isol) ac12fgml q6012rh5 s to-220 (n.isol) ac12fsm q6012lh5 s to-220 (isol) ac16bgm q2015r5 s to-220 (n.isol) ac16bsm q2015l5 s to-220 (isol) ac16dgm q4015r5 s to-220 (n.isol) ac16dsm q4015l5 s to-220 (isol) ac16egm q6015r5 s to-220 (n.isol) ac16esm q6015l5 s to-220 (isol) ac16fgm q6015r5 s to-220 (n.isol) ac16fsm q6015l5 s to-220 (isol) ac25b1fl q6025p5 s fastpak (isol) ac25d1fl q6025p5 s fastpak (isol) ac25e1fl q6025p5 s fastpak (isol) ac25f1fl q6025p5 s fastpak (isol) bcr3as-12 q6006dh3 d to-252 (smt) bcr3as-8 q4006dh3 d to-252 (smt) bt131w-600 l6n3 s sot223 / compak bt136-500 q6004f41 s to-202 (n.isol) bt136-500d l6004f61 s to-202 (n.isol) bt136-500e l6004f81 s to-202 (n.isol) bt136-500f q6004f41 s to-202 (n.isol) bt136-500g q6004f41 s to-202 (n.isol) bt136-600 q6004f41 s to-202 (n.isol) bt136-600d l6004f61 s to-202 (n.isol) bt136-600e l6004f81 s to-202 (n.isol) bt136-600f q6004f41 s to-202 (n.isol) bt136-600g q6004f41 s to-202 (n.isol) bt136-800 q8004l4 s to-220 (isol) bt136-800f q8004l4 s to-220 (isol) bt136-800g q8004l4 s to-220 (isol) bt136f-500 q6004l4 s to-220 (isol) bt136f-500d l6004l6 s to-220 (isol) bt136f-500e l6004l8 s to-220 (isol) bt136f-500f q6004l4 s to-220 (isol) bt136f-500g q6004l4 s to-220 (isol) bt136f-600 q6004l4 s to-220 (isol) part number teccor device direct or suggested replacement teccor package bt136f-600d l6004l6 s to-220 (isol) bt136f-600e l6004l8 s to-220 (isol) bt136f-600f q6004l4 s to-220 (isol) bt136f-600g q6004l4 s to-220 (isol) bt136f-800 q8004l4 s to-220 (isol) bt136f-800f q8004l4 s to-220 (isol) bt136f-800g q8004l4 s to-220 (isol) bt136s-600d l6004d5 s to-252 (smt) BT136S-600E l6004d6 s to-252 (smt) bt136s-600f l6004d8 s to-252 (smt) bt136x-500 q6004l4 s to-220 (isol) bt136x-500d l6004l6 s to-220 (isol) bt136x-500e l6004l8 s to-220 (isol) bt136x-500f q6004l4 s to-220 (isol) bt136x-500g q6004l4 s to-220 (isol) bt136x-600 q6004l4 s to-220 (isol) bt136x-600d l6004l6 s to-220 (isol) bt136x-600e l6004l8 s to-220 (isol) bt136x-600f q6004l4 s to-220 (isol) bt136x-600g q6004l4 s to-220 (isol) bt136x-800 q8004l4 s to-220 (isol) bt136x-800f q8004l4 s to-220 (isol) bt136x-800g q8004l4 s to-220 (isol) bt137-500 q6008r4 s to-220 (n.isol) bt137-500d l6008l6 s to-220 (isol) bt137-500e l6008l8 s to-220 (isol) bt137-500f q6008r4 s to-220 (n.isol) bt137-500g q6008r4 s to-220 (n.isol) bt137-600d l6008l6 s to-220 (isol) bt137-600e l6008l8 s to-220 (isol) bt137-600g q6008r5 s to-220 (n.isol) bt137-800g q8008r5 s to-220 (n.isol) bt137b-600 q6010n4 s to-263 (smt) bt137b-600f q6010n4 s to-263 (smt) bt137f-500 q6008l4 s to-220 (isol) bt137f-500d l6008l6 s to-220 (isol) bt137f-500e l6008l8 s to-220 (isol) bt137f-500f q6008l4 s to-220 (isol) bt137f-500g q6008l4 s to-220 (isol) bt137f-600d l6008l6 s to-220 (isol) bt137f-600e l6008l8 s to-220 (isol) bt137f-600g q6008l5 s to-220 (isol) bt137f-800g q8008l5 s to-220 (isol) bt137s-600e l6008d8 s to-252 (smt) bt137x-500 q6008l4 s to-220 (isol) bt137x-500d l6008l6 s to-220 (isol) bt137x-500e l6008l8 s to-220 (isol) bt137x-500f q6008l4 s to-220 (isol) bt137x-500g q6008l4 s to-220 (isol) bt137x-600d l6008l6 s to-220 (isol) bt137x-600e l6008l8 s to-220 (isol) bt137x-600g q6008l5 s to-220 (isol) bt137x-800g q8008l5 s to-220 (isol) bt138-500g q6015r5 s to-220 (n.isol) bt138-600g q6015r5 s to-220 (n.isol) bt138-800g q8015r5 s to-220 (n.isol) bt138f-500g q6015l5 s to-220 (isol) bt138f-600g q6015l5 s to-220 (isol) bt138f-800g q8015l5 s to-220 (isol) bt138x-500g q6015l5 s to-220 (isol) bt138x-600g q6015l5 s to-220 (isol) bt138x-800g q8015l5 s to-220 (isol) bt139-500g q6015r5 s to-220 (n.isol) bt139-600g q6015r5 s to-220 (n.isol) bt139-800g q8015r5 s to-220 (n.isol) bt139f-500g q6015l5 s to-220 (isol) bt139f-600g q6015l5 s to-220 (isol) bt139f-800g q8015l5 s to-220 (isol) bt139x-500g q6015l5 s to-220 (isol) bt139x-500h q6015l6 s to-220 (isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-4 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog bt139x-600g q6015l5 s to-220 (isol) bt139x-600h q6015l6 s to-220 (isol) bt139x-800g q8015l5 s to-220 (isol) bt139x-800h q8015l6 s to-220 (isol) bt145-500r q6025r s to-220 (n.isol) bt145-600r q6025r s to-220 (n.isol) bt145-800r q8025r s to-220 (n.isol) bt149b ec103b s to-92 (isol) bt149d ec103d s to-92 (isol) bt149e ec103m s to-92 (isol) bt149g ec103m s to-92 (isol) bt150-500r t106m1 s to-202 (n.isol) bt150-600r t106m1 s to-202 (n.isol) bt150s-600r s6004ds2 s to-252 (smt) bt151-500r s6010r s to-220 (n.isol) bt151-650r s8010r s to-220 (n.isol) bt151-800r s8010r s to-220 (n.isol) bt151s-500r s6012d s to-252 (smt) bt151s-650r s8012d s to-252 (smt) bt151x-500 s6010l s to-220 (isol) bt151x-650 s8010l s to-220 (isol) bt151x-800 s8010l s to-220 (isol) bt152-400r s4020l s to-220 (isol) bt152-600r s6020l s to-220 (isol) bt152-800r s8020l s to-220 (isol) bt152b-400r s4025n s to-263 (smt) bt152b-600r s6025n s to-263 (smt) bt152b-800r s8025n s to-263 (smt) bt168b ec103b s to-92 (isol) bt168d ec103d s to-92 (isol) bt168e ec103m s to-92 (isol) bt168g ec103m s to-92 (isol) bt169b ec103b d to-92 (isol) bt169d ec103d d to-92 (isol) bt169e ec103m d to-92 (isol) bt169g ec103m d to-92 (isol) bt300-500r s6008r s to-220 (n.isol) bt300-600r s6008r s to-220 (n.isol) bt300-800r s8008r s to-220 (n.isol) bt300s-600r s6008d d to-252 (smt) bta04-200a l2004l8 d to-220 (isol) bta04-200d l2004l6 d to-220 (isol) bta04-200gp l2004l6 s to-220 (isol) bta04-200s l2004l6 d to-220 (isol) bta04-200t l2004l5 d to-220 (isol) bta04-400a l4004l8 d to-220 (isol) bta04-400d l4004l6 d to-220 (isol) bta04-400gp l4004l6 s to-220 (isol) bta04-400s l4004l6 d to-220 (isol) bta04-400t l4004l5 d to-220 (isol) bta04-600a l6004l8 d to-220 (isol) bta04-600d l6004l6 d to-220 (isol) bta04-600gp l6004l6 s to-220 (isol) bta04-600s l6004l6 d to-220 (isol) bta04-600t l6004l5 d to-220 (isol) bta06-200a l2006l8 d to-220 (isol) bta06-200b q2006l4 s to-220 (isol) bta06-200c q2006l4 s to-220 (isol) bta06-200d l2006l6 d to-220 (isol) bta06-200gp l2006l6 s to-220 (isol) bta06-200s l2006l6 d to-220 (isol) bta06-200sw l2006l8 d to-220 (isol) bta06-200t l2006l5 s to-220 (isol) bta06-200tw l2006l6 d to-220 (isol) bta06-400a l4006l8 d to-220 (isol) bta06-400b q4006l4 s to-220 (isol) bta06-400bw q4006lh4 s to-220 (isol) bta06-400c q4006l4 s to-220 (isol) bta06-400cw q4006lh4 d to-220 (isol) bta06-400d l4006l6 d to-220 (isol) part number teccor device direct or suggested replacement teccor package bta06-400gp l4006l6 s to-220 (isol) bta06-400s l4006l6 d to-220 (isol) bta06-400sw l4006l8 d to-220 (isol) bta06-400t l4006l5 s to-220 (isol) bta06-400tw l4006l6 d to-220 (isol) bta06-600a l6006l8 d to-220 (isol) bta06-600b q6006l5 s to-220 (isol) bta06-600bw q6006lh4 s to-220 (isol) bta06-600c q6006l5 s to-220 (isol) bta06-600cw q6006lh4 s to-220 (isol) bta06-600d l6006l6 d to-220 (isol) bta06-600gp l6006l6 s to-220 (isol) bta06-600s l6006l6 d to-220 (isol) bta06-600sw l6006l8 d to-220 (isol) bta06-600t l6006l5 s to-220 (isol) bta06-600tw l6006l6 d to-220 (isol) bta06-700b q8006l5 s to-220 (isol) bta06-700bw q8006lh4 s to-220 (isol) bta06-700c q8006l5 d to-220 (isol) bta06-700cw q7006lh4 d to-220 (isol) bta06-800b q8006l5 s to-220 (isol) bta06-800bw q8006lh4 s to-220 (isol) bta06-800c q8006l5 s to-220 (isol) bta06-800cw q8006lh4 d to-220 (isol) bta08-200a l2008l8 d to-220 (isol) bta08-200b q2008l4 s to-220 (isol) bta08-200c q2008l4 s to-220 (isol) bta08-200s l2008l6 d to-220 (isol) bta08-200sw l2008l8 d to-220 (isol) bta08-200tw l2008l6 d to-220 (isol) bta08-400a l4008l8 d to-220 (isol) bta08-400b q4008l4 s to-220 (isol) bta08-400bw q4008lh4 s to-220 (isol) bta08-400c q4008l4 s to-220 (isol) bta08-400cw q4008lh4 d to-220 (isol) bta08-400s l4008l6 d to-220 (isol) bta08-400sw l4008l8 d to-220 (isol) bta08-400tw l4008l6 d to-220 (isol) bta08-600a l6008l8 d to-220 (isol) bta08-600b q6008l5 s to-220 (isol) bta08-600bw q6008lh4 s to-220 (isol) bta08-600c q6008l5 s to-220 (isol) bta08-600cw q6008lh4 d to-220 (isol) bta08-600s l6008l6 d to-220 (isol) bta08-600sw l6008l8 d to-220 (isol) bta08-600tw l6008l6 d to-220 (isol) bta08-700b q8008l5 s to-220 (isol) bta08-700bw q8008lh4 s to-220 (isol) bta08-700c q8008l5 s to-220 (isol) bta08-700cw q8008lh4 d to-220 (isol) bta08-800b q8008l5 s to-220 (isol) bta08-800bw q8008lh4 s to-220 (isol) bta08-800c q8008l5 s to-220 (isol) bta08-800cw q8008lh4 d to-220 (isol) bta10-200aw q2010l5 s to-220 (isol) bta10-200b q2010l5 s to-220 (isol) bta10-200bw q2010lh5 d to-220 (isol) bta10-200c q2010l5 s to-220 (isol) bta10-200cw q2010lh5 s to-220 (isol) bta10-400aw q4010l5 s to-220 (isol) bta10-400b q4010l5 s to-220 (isol) bta10-400bw q4010lh5 d to-220 (isol) bta10-400c q4010l5 s to-220 (isol) bta10-400cw q4010lh5 s to-220 (isol) bta10-400gp q4010l4 s to-220 (isol) bta10-600aw q6010l5 s to-220 (isol) bta10-600b q6010l5 s to-220 (isol) bta10-600bw q6010lh5 d to-220 (isol) bta10-600c q6010l5 s to-220 (isol) bta10-600cw q6010lh5 s to-220 (isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-5 http://www.teccor.com thyristor product catalog +1 972-580-7777 bta10-600gp q6010l4 s to-220 (isol) bta10-700aw q8010l5 s to-220 (isol) bta10-700b q8010l5 s to-220 (isol) bta10-700bw q8010lh5 d to-220 (isol) bta10-700c q8010l5 s to-220 (isol) bta10-700cw q8010lh5 s to-220 (isol) bta10-800b q8010l5 s to-220 (isol) bta10-800bw q8010lh5 d to-220 (isol) bta10-800c q8010l5 s to-220 (isol) bta10-800cw q8010lh5 s to-220 (isol) bta12-200aw q2012lh5 d to-220 (isol) bta12-200b q2015l5 s to-220 (isol) bta12-200bw q4012lh5 d to-220 (isol) bta12-200c q2015l5 s to-220 (isol) bta12-400aw q4012lh5 d to-220 (isol) bta12-400b q4015l5 s to-220 (isol) bta12-400bw q4012lh5 d to-220 (isol) bta12-400c q4015l5 s to-220 (isol) bta12-400cw q4012lh5 s to-220 (isol) bta12-600aw q6012lh5 d to-220 (isol) bta12-600b q6015l5 s to-220 (isol) bta12-600bw q6012lh5 d to-220 (isol) bta12-600c q6015l5 s to-220 (isol) bta12-600cw q6012lh5 s to-220 (isol) bta12-700aw q8012lh5 d to-220 (isol) bta12-700b q8015l5 s to-220 (isol) bta12-700bw q8012lh5 d to-220 (isol) bta12-700c q8015l5 s to-220 (isol) bta12-700cw q8012lh5 s to-220 (isol) bta12-800b q8015l5 s to-220 (isol) bta12-800bw q8012lh5 s to-220 (isol) bta12-800c q8015l5 s to-220 (isol) bta12-800cw q8012lh5 s to-220 (isol) bta13-200b q2015l5 s to-220 (isol) bta13-400b q4015l5 s to-220 (isol) bta13-600b q6015l5 s to-220 (isol) bta13-700b q8015l5 s to-220 (isol) bta13-800b q8015l5 s to-220 (isol) bta140-500 q6025r5 s to-220 (n.isol) bta140-600 q6025r5 s to-220 (n.isol) bta140-800 q8025r5 s to-220 (n.isol) bta16-200aw q2016lh6 s to-220 (isol) bta16-200b q2015l5 s to-220 (isol) bta16-200bw q2016lh4 s to-220 (isol) bta16-400aw q2016lh6 s to-220 (isol) bta16-400b q2015l5 s to-220 (isol) bta16-400bw q2016lh4 s to-220 (isol) bta16-400cw q4016lh4 s to-220 (isol) bta16-600aw q6016lh6 s to-220 (isol) bta16-600b q6015l5 s to-220 (isol) bta16-600bw q6016lh4 s to-220 (isol) bta16-600cw q6016lh4 s to-220 (isol) bta16-700aw q8016lh6 s to-220 (isol) bta16-700b q8015l5 s to-220 (isol) bta16-700bw q8016lh4 s to-220 (isol) bta16-700cw q8016lh4 s to-220 (isol) bta16-800aw q8016lh6 s to-220 (isol) bta16-800b q8015l5 s to-220 (isol) bta16-800bw q8016lh4 s to-220 (isol) bta16-800cw q8016lh4 s to-220 (isol) bta20-400bw q4025l6 s to-220 (isol) bta20-400cw q4025l6 s to-220 (isol) bta204s-600c q6006dh4 d to-252 (smt) bta204s-600e q6006dh3 d to-252 (smt) bta20-600bw q6025l6 s to-220 (isol) bta20-600cw q6025l6 s to-220 (isol) bta20-700bw q8025l6 s to-220 (isol) bta20-700cw q8025l6 s to-220 (isol) bta20-800bw q8025l6 s to-220 (isol) bta20-800cw q8025l6 s to-220 (isol) part number teccor device direct or suggested replacement teccor package bta208-600b q6008rh4 s to-220 (n.isol bta208-800b q8008rh4 s to-220 (n.isol bta208s-600e q6008dh3 d to-252 (smt) bta208s-800c q8008dh4 d to-252 (smt) bta208x-600b q6008lh4 s to-220 (isol) bta208x-800b q8008lh4 s to-220 (isol) bta20c q4006r4 d to-220 (n.isol) bta20d q4006r4 d to-220 (n.isol) bta20e q6006r4 d to-220 (n.isol) bta20m q6006r5 d to-220 (n.isol) bta20n q8006r5 d to-220 (n.isol) bta212-600b q6012rh5 s to-220 (n.isol) bta212-800b q8012rh5 s to-220 (n.isol) bta212b-600b q6012nh5 d to-263 (smt) bta212b-800b q8012nh5 d to-263 (smt) bta212x-600b q6012lh5 s to-220 (isol) bta212x-800b q8012lh5 s to-220 (isol) bta216-600b q6015r6 s to-220 (n.isol) bta216-800b q8015r6 s to-220 (n.isol) bta216b-600 q6016nh4 s to-263 (smt) bta216x-600b q6015l6 s to-220 (isol) bta216x-800b q8015l6 s to-220 (isol) bta21c q4008r4 d to-220 (n.isol) bta21d q4008r4 d to-220 (n.isol) bta21e q6008r4 d to-220 (n.isol) bta21m q6008r5 s to-220 (n.isol) bta21n q8008r5 s to-220 (n.isol) bta225-600b q6025r6 s to-220 (n.isol) bta225-800b q8025r6 s to-220 (n.isol) bta225b-600b q6025nh6 s to-263 (smt) bta225b-800b q8025nh6 s to-263 (smt) bta22b q2010r5 s to-220 (n.isol) bta22c q4010r5 s to-220 (n.isol) bta22d q4010r5 s to-220 (n.isol) bta22e q5010r5 s to-220 (n.isol) bta22m q6010r5 s to-220 (n.isol) bta23b q2015r5 s to-220 (n.isol) bta23c q4015r5 s to-220 (n.isol) bta23d q4015r5 s to-220 (n.isol) bta23e q5015r5 s to-220 (n.isol) bta23m q6015r5 s to-220 (n.isol) bta24-600bw q6025l6 s to-220 (isol) bta24-600cw q6025l6 s to-220 (isol) bta24-700bw q8025l6 s to-220 (isol) bta24-700cw q8025l6 s to-220 (isol) bta24-800bw q8025l6 s to-220 (isol) bta24-800cw q8025l6 s to-220 (isol) bta25-200a q6025p5 s fastpak (isol) bta25-200b q6025p5 s fastpak (isol) bta25-400a q6025p5 s fastpak (isol) bta25-400b q6025p5 s fastpak (isol) bta25-600a q6025p5 s fastpak (isol) bta25-600b q6025p5 s fastpak (isol) bta25-600bw q6025p5 s fastpak (isol) bta25-600cw q6025p5 s fastpak (isol) bta25-700a q8025p5 s fastpak (isol) bta25-700b q8025p5 s fastpak (isol) bta25-800a q8025p5 s fastpak (isol) bta25-800b q8025p5 s fastpak (isol) bta25-800bw q8025p5 s fastpak (isol) bta25-800cw q8025p5 s fastpak (isol) bta26-200a q2025k6 s to-218 (isol) bta26-200b q2025k6 s to-218 (isol) bta26-400a q4025k6 s to-218 (isol) bta26-400b q4025k6 s to-218 (isol) bta26-400bw q4025k6 s to-218 (isol) bta26-400cw q4025k6 s to-218 (isol) bta26-600a q6025k6 s to-218 (isol) bta26-600b q6025k6 s to-218 (isol) bta26-600bw q6025k6 s to-218 (isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-6 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog bta26-600cw q6025k6 s to-218 (isol) bta26-700a q8025k6 s to-218 (isol) bta26-700b q8025k6 s to-218 (isol) bta26-700bw q8025k6 s to-218 (isol) bta26-700cw q8025k6 s to-218 (isol) bta26-800a q8025k6 s to-218 (isol) bta26-800b q8025k6 s to-218 (isol) bta26-800bw q8025k6 s to-218 (isol) bta26-800cw q8025k6 s to-218 (isol) bta40-200a q6035p5 s fastpak (isol) bta40-200b q6035p5 s fastpak (isol) bta40-400a q6035p5 s fastpak (isol) bta40-400b q6035p5 s fastpak (isol) bta40-600a q6035p5 s fastpak (isol) bta40-600b q6035p5 s fastpak (isol) bta40-700a q8035p5 s fastpak (isol) bta40-700b q8035p5 s fastpak (isol) bta41-200a q2040k7 s to-218 (isol) bta41-200b q2040k7 s to-218 (isol) bta41-400a q4040k7 s to-218 (isol) bta41-400b q4040k7 s to-218 (isol) bta41-600a q6040k7 s to-218 (isol) bta41-600b q6040k7 s to-218 (isol) bta41-700a q8040k7 s to-218 (isol) bta41-700b q8040k7 s to-218 (isol) bta41-800a q8040k7 s to-218 (isol) bta41-800b q8040k7 s to-218 (isol) btb04-200a l2004f81 s to-202 (n.isol) btb04-200d l2004f61 s to-202 (n.isol) btb04-200s l2004f61 s to-202 (n.isol) btb04-200t l2004f51 s to-202 (n.isol) btb04-400a l4004f81 s to-202 (n.isol) btb04-400d l4004f61 s to-202 (n.isol) btb04-400s l4004f61 s to-202 (n.isol) btb04-400t l4004f51 s to-202 (n.isol) btb04-600a l6004f61 s to-202 (n.isol) btb04-600d l6004f61 s to-202 (n.isol) btb04-600s l6004f81 s to-202 (n.isol) btb04-600t l6004f51 s to-202 (n.isol) btb06-200a l2006l8 s to-220 (isol) btb06-200b q2006r4 s to-220 (n.isol) btb06-200c q2006r4 s to-220 (n.isol) btb06-200d l2006l6 s to-220 (isol) btb06-200s l2006l6 s to-220 (isol) btb06-200t l2006l5 s to-220 (isol) btb06-400a l4006l8 s to-220 (isol) btb06-400b q4006r4 s to-220 (n.isol) btb06-400bw q4006rh4 s to-220 (n.isol) btb06-400c q4006r4 s to-220 (n.isol) btb06-400cw q4006rh4 s to-220 (n.isol) btb06-400d l4006l6 s to-220 (isol) btb06-400s l4006l6 s to-220 (isol) btb06-400t l4006l5 s to-220 (isol) btb06-600a l6006l8 s to-220 (isol) btb06-600b q6006r5 s to-220 (n.isol) btb06-600bw q6006rh4 s to-220 (n.isol) btb06-600c q6006r5 s to-220 (n.isol) btb06-600cw q6006rh4 s to-220 (n.isol) btb06-600d l6006l6 s to-220 (isol) btb06-600s l6006l6 s to-220 (isol) btb06-600t l6006l5 s to-220 (isol) btb06-700b q8006r5 s to-220 (n.isol) btb06-700bw q8006rh4 s to-220 (n.isol) btb06-700c q8006r5 s to-220 (n.isol) btb06-700cw q8006rh4 s to-220 (n.isol) btb06-800b q8006r5 s to-220 (n.isol) btb06-800bw q8006rh4 s to-220 (n.isol) btb06-800c q8006r5 s to-220 (n.isol) btb06-800cw q8006rh4 s to-220 (n.isol) btb08-200a l2008l8 s to-220 (isol) part number teccor device direct or suggested replacement teccor package btb08-200b q2008r4 s to-220 (n.isol) btb08-200c q2008r4 s to-220 (n.isol) btb08-200s l2008l6 s to-220 (isol) btb08-400a l4008l8 s to-220 (isol) btb08-400b q4008r4 s to-220 (n.isol) btb08-400bw q4008rh4 s to-220 (n.isol) btb08-400c q4008r4 s to-220 (n.isol) btb08-400cw q4008rh4 s to-220 (n.isol) btb08-400s l4008l6 s to-220 (isol) btb08-600a l6008l8 s to-220 (isol) btb08-600b q6008r5 s to-220 (n.isol) btb08-600bw q6008rh4 s to-220 (n.isol) btb08-600c q6008r5 s to-220 (n.isol) btb08-600cw q6008rh4 s to-220 (n.isol) btb08-600s l6008l6 s to-220 (isol) btb08-700b q8008r5 s to-220 (n.isol) btb08-700bw q8008rh4 s to-220 (n.isol) btb08-700c q8008r5 s to-220 (n.isol) btb08-700cw q8008rh4 s to-220 (n.isol) btb08-800b q8008r5 s to-220 (n.isol) btb08-800bw q8008rh4 s to-220 (n.isol) btb08-800c q8008r5 s to-220 (n.isol) btb08-800cw q8008rh4 s to-220 (n.isol) btb10-200b q2010r5 s to-220 (n.isol) btb10-200c q2010r5 s to-220 (n.isol) btb10-400b q4010r5 s to-220 (n.isol) btb10-400bw q4010rh5 s to-220 (n.isol) btb10-400c q4010r5 s to-220 (n.isol) btb10-400cw q4010rh5 s to-220 (n.isol) btb10-600b q6010r5 s to-220 (n.isol) btb10-600bw q6010rh5 s to-220 (n.isol) btb10-600c q6010r5 s to-220 (n.isol) btb10-600cw q6010rh5 s to-220 (n.isol) btb10-700b q8010r5 s to-220 (n.isol) btb10-700bw q8010rh5 s to-220 (n.isol) btb10-700c q8010r5 s to-220 (n.isol) btb10-700cw q8010rh5 s to-220 (n.isol) btb10-800b q8010r5 s to-220 (n.isol) btb10-800bw q8010rh5 s to-220 (n.isol) btb10-800c q8010r5 s to-220 (n.isol) btb10-800cw q8010rh5 s to-220 (n.isol) btb12-200b q2015r5 s to-220 (n.isol) btb12-200c q2015r5 s to-220 (n.isol) btb12-400b q4015r5 s to-220 (n.isol) btb12-400bw q4012rh5 s to-220 (n.isol) btb12-400c q4015r5 s to-220 (n.isol) btb12-400cw q4012rh5 s to-220 (n.isol) btb12-400sw q4016rh3 s to-220 (n.isol) btb12-600b q6015r5 s to-220 (n.isol) btb12-600bw q6012rh5 s to-220 (n.isol) btb12-600c q6015r5 s to-220 (n.isol) btb12-600cw q6012rh5 s to-220 (n.isol) btb12-600sw q6016rh3 s to-220 (n.isol) btb12-700b q8015r5 s to-220 (n.isol) btb12-700bw q8012rh5 s to-220 (n.isol) btb12-700c q8015r5 s to-220 (n.isol) btb12-700cw q8012rh5 s to-220 (n.isol) btb12-700sw q8016rh3 s to-220 (n.isol) btb12-800b q8015r5 s to-220 (n.isol) btb12-800bw q8012rh5 s to-220 (n.isol) btb12-800c q8015r5 s to-220 (n.isol) btb12-800cw q8012rh5 s to-220 (n.isol) btb13-200b q2015r5 s to-220 (n.isol) btb13-400b q4015r5 s to-220 (n.isol) btb13-600b q6015r5 s to-220 (n.isol) btb13-700b q8015r5 s to-220 (n.isol) btb13-800b q8015r5 s to-220 (n.isol) btb15-200b q2015r5 s to-220 (n.isol) btb15-400b q4015r5 s to-220 (n.isol) btb15-600b q6015r5 s to-220 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-7 http://www.teccor.com thyristor product catalog +1 972-580-7777 btb15-700b q8015r5 s to-220 (n.isol) btb16-200b q2015r5 s to-220 (n.isol) btb16-400b q4015r5 s to-220 (n.isol) btb16-400cw q4016rh4 s to-220 (n.isol) btb16-600b q6015r5 s to-220 (n.isol) btb16-600cw q6016rh4 s to-220 (n.isol) btb16-700b q8015r5 s to-220 (n.isol) btb16-700cw q8016rh4 s to-220 (n.isol) btb16-800b q8015r5 s to-220 (n.isol) btb16-800cw q8016rh4 s to-220 (n.isol) btb19-200b q2025r5 s to-220 (n.isol) btb19-400b q4025r5 s to-220 (n.isol) btb19-600b q6025r5 s to-220 (n.isol) btb19-700b q8025r5 s to-220 (n.isol) btb20-400bw q4025r6 s to-220 (n.isol) btb20-400cw q4025r6 s to-220 (n.isol) btb20-600bw q6025r6 s to-220 (n.isol) btb20-600cw q6025r6 s to-220 (n.isol) btb20-700bw q8025r6 s to-220 (n.isol) btb20-700cw q8025r6 s to-220 (n.isol) btb20-800bw q8025r6 s to-220 (n.isol) btb20-800cw q8025r6 s to-220 (n.isol) btb24-200b q2025r5 s to-220 (n.isol) btb24-400b q4025r5 s to-220 (n.isol) btb24-600b q6025r5 s to-220 (n.isol) btb24-600bw q6025r6 s to-220 (n.isol) btb24-700b q8025r5 s to-220 (n.isol) btb24-800b q8025r5 s to-220 (n.isol) btb26-200a q2025k6 s to-218 (isol) btb26-200b q2025k6 s to-218 (isol) btb26-400a q4025k6 s to-218 (isol) btb26-400b q4025k6 s to-218 (isol) btb26-600a q6025k6 s to-218 (isol) btb26-600b q6025k6 s to-218 (isol) btb26-700a q8025k6 s to-218 (isol) btb26-700b q8025k6 s to-218 (isol) btb26-800b q8025k6 s to-218 (isol) btb41-200a q2040k7 s to-218 (isol) btb41-200b q2040k7 s to-218 (isol) btb41-400a q4040k7 s to-218 (isol) btb41-400b q4040k7 s to-218 (isol) btb41-600a q6040k7 s to-218 (isol) btb41-600b q6040k7 s to-218 (isol) btb41-700a q8040k7 s to-218 (isol) btb41-700b q8040k7 s to-218 (isol) btb41-800a q8040k7 s to-218 (isol) btb41-800b q8040k7 s to-218 (isol) btw41-500g q6035p5 s fastpak (isol) btw41-600g q6035p5 s fastpak (isol) btw66-200 s2035j s to-218 (isol) btw66-400 s4035j s to-218 (isol) btw66-600 s6035j s to-218 (isol) btw66-800 s8035j s to-218 (isol) btw67-200 s2065j s to-218 (isol) btw67-400 s4065j s to-218 (isol) btw67-600 s6065j s to-218 (isol) btw67-800 s8065j s to-218 (isol) btw68-200 s2035k d to-218 (isol) btw68-200n s2035k s to-218 (isol) btw68-400 s4035k d to-218 (isol) btw68-400n s4035k s to-218 (isol) btw68-600 s6035k d to-218 (isol) btw68-600n s6035k s to-218 (isol) btw68-800 s8035k d to-218 (isol) btw68-800n s8035k s to-218 (isol) btw69-200 s2065k d to-218 (isol) btw69-200n s2055m d to-218 (n.isol) btw69-400 s4065k d to-218 (isol) btw69-400n s4055m d to-218 (n.isol) btw69-600 s6065k d to-218 (isol) part number teccor device direct or suggested replacement teccor package btw69-600n s6055m d to-218 (n.isol) btw69-800 s8065k d to-218 (isol) btw69-800n s8055m d to-218 (n.isol) btw70-200n s2070w s to-218 (n.isol) btw70-400n s4070w s to-218 (n.isol) btw70-600n s6070w s to-218 (n.isol) byw80-100 d2020l s to-220 (isol) byw80-150 d2020l s to-220 (isol) byw80-200 d2020l s to-220 (isol) byw80-50 d2020l s to-220 (isol) c103a ec103b s to-92 (isol) c103b ec103b s to-92 (isol) c103d ec103d s to-92 (isol) c103e ec103m s to-92 (isol) c103m ec103m s to-92 (isol) c103y ec103b s to-92 (isol) c103yy ec103b s to-92 (isol) c106a t106b1 s to-202 (n.isol) c106a1 t106b1 s to-202 (n.isol) c106a11 t106b11 s to-202 (n.isol) c106a12 t106b12 s to-202 (n.isol) c106a2 t106b2 s to-202 (n.isol) c106a21 t106b21 s to-202 (n.isol) c106a3 t106b3 s to-202 (n.isol) c106a32 t106b32 s to-202 (n.isol) c106a4 t106b4 s to-202 (n.isol) c106a41 t106b41 s to-202 (n.isol) c106b t106b1 s to-202 (n.isol) c106b1 t106b1 s to-202 (n.isol) c106b11 t106b11 s to-202 (n.isol) c106b12 t106b12 s to-202 (n.isol) c106b2 t106b2 s to-202 (n.isol) c106b21 t106b21 s to-202 (n.isol) c106b3 t106b3 s to-202 (n.isol) c106b32 t106b32 s to-202 (n.isol) c106b4 t106b4 s to-202 (n.isol) c106b41 t106b41 s to-202 (n.isol) c106c t106d s to-202 (n.isol) c106c1 t106d1 s to-202 (n.isol) c106c11 t106d11 s to-202 (n.isol) c106c12 t106d12 s to-202 (n.isol) c106c2 t106d2 s to-202 (n.isol) c106c21 t106d1 s to-202 (n.isol) c106c3 t106d3 s to-202 (n.isol) c106c32 t106d32 s to-202 (n.isol) c106c4 t106d4 s to-202 (n.isol) c106c41 t106d41 s to-202 (n.isol) c106d t106d1 s to-202 (n.isol) c106d1 t106d1 s to-202 (n.isol) c106d11 t106d11 s to-202 (n.isol) c106d12 t106d12 s to-202 (n.isol) c106d2 t106d2 s to-202 (n.isol) c106d21 t106d21 s to-202 (n.isol) c106d3 t106d3 s to-202 (n.isol) c106d32 t106d32 s to-202 (n.isol) c106d4 t106d4 s to-202 (n.isol) c106d41 t106d41 s to-202 (n.isol) c106e t106m1 s to-202 (n.isol) c106e1 t106m1 s to-202 (n.isol) c106e11 t106m11 s to-202 (n.isol) c106e12 t106m12 s to-202 (n.isol) c106e2 t106m2 s to-202 (n.isol) c106e21 t106m21 s to-202 (n.isol) c106e3 t106m3 s to-202 (n.isol) c106e32 t106m32 s to-202 (n.isol) c106e4 t106m4 s to-202 (n.isol) c106e41 t106m41 s to-202 (n.isol) c106f t106b1 s to-202 (n.isol) c106f1 t106b1 s to-202 (n.isol) c106f11 t106b11 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-8 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog c106f12 t106b12 s to-202 (n.isol) c106f2 t106b2 s to-202 (n.isol) c106f21 t106b21 s to-202 (n.isol) c106f3 t106b3 s to-202 (n.isol) c106f32 t106b32 s to-202 (n.isol) c106f4 t106b4 s to-202 (n.isol) c106f41 t106b41 s to-202 (n.isol) c106m t106m1 s to-202 (n.isol) c106m1 t106m1 s to-202 (n.isol) c106m11 t106m11 s to-202 (n.isol) c106m12 t106m12 s to-202 (n.isol) c106m2 t106m2 s to-202 (n.isol) c106m21 t106m21 s to-202 (n.isol) c106m3 t106m3 s to-202 (n.isol) c106m32 t106m32 s to-202 (n.isol) c106m4 t106m4 s to-202 (n.isol) c106m41 t106m41 s to-202 (n.isol) c106q t106b1 s to-202 (n.isol) c106q1 t106b1 s to-202 (n.isol) c106q11 t106b11 s to-202 (n.isol) c106q12 t106b12 s to-202 (n.isol) c106q2 t106b2 s to-202 (n.isol) c106q21 t106b21 s to-202 (n.isol) c106q3 t106b3 s to-202 (n.isol) c106q32 t106b32 s to-202 (n.isol) c106q4 t106b4 s to-202 (n.isol) c106q41 t106b41 s to-202 (n.isol) c106y t106b1 s to-202 (n.isol) c106y1 t106b1 s to-202 (n.isol) c106y11 t106b11 s to-202 (n.isol) c106y12 t106b12 s to-202 (n.isol) c106y2 t106b2 s to-202 (n.isol) c106y21 t106b21 s to-202 (n.isol) c106y3 t106b3 s to-202 (n.isol) c106y32 t106b32 s to-202 (n.isol) c106y4 t106b4 s to-202 (n.isol) c106y41 t106b41 s to-202 (n.isol) c107a t107b1 s to-202 (n.isol) c107a1 t107b1 s to-202 (n.isol) c107a11 t107b11 s to-202 (n.isol) c107a12 t107b12 s to-202 (n.isol) c107a2 t107b2 s to-202 (n.isol) c107a21 t107b21 s to-202 (n.isol) c107a3 t107b3 s to-202 (n.isol) c107a32 t107b32 s to-202 (n.isol) c107a4 t107b4 s to-202 (n.isol) c107a41 t107b41 s to-202 (n.isol) c107b t107b1 s to-202 (n.isol) c107b1 t107b1 s to-202 (n.isol) c107b11 t107b11 s to-202 (n.isol) c107b12 t107b12 s to-202 (n.isol) c107b2 t107b2 s to-202 (n.isol) c107b21 t107b21 s to-202 (n.isol) c107b3 t107b3 s to-202 (n.isol) c107b32 t107b32 s to-202 (n.isol) c107b4 t107b4 s to-202 (n.isol) c107b41 t107b41 s to-202 (n.isol) c107c t107d1 s to-202 (n.isol) c107c1 t107d1 s to-202 (n.isol) c107c11 t107d11 s to-202 (n.isol) c107c12 t107d12 s to-202 (n.isol) c107c2 t107d2 s to-202 (n.isol) c107c21 t107d21 s to-202 (n.isol) c107c3 t107d3 s to-202 (n.isol) c107c32 t107d32 s to-202 (n.isol) c107c4 t107d4 s to-202 (n.isol) c107c41 t107d41 s to-202 (n.isol) c107d t107d1 s to-202 (n.isol) c107d1 t107d1 s to-202 (n.isol) c107d11 t107d11 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package c107d12 t107d12 s to-202 (n.isol) c107d2 t107d2 s to-202 (n.isol) c107d21 t107d21 s to-202 (n.isol) c107d3 t107d3 s to-202 (n.isol) c107d32 t107d32 s to-202 (n.isol) c107d4 t107d4 s to-202 (n.isol) c107d41 t107d41 s to-202 (n.isol) c107e t107m1 s to-202 (n.isol) c107e1 t107m1 s to-202 (n.isol) c107e11 t107m11 s to-202 (n.isol) c107e12 t107m12 s to-202 (n.isol) c107e2 t107m2 s to-202 (n.isol) c107e21 t107m21 s to-202 (n.isol) c107e3 t107m3 s to-202 (n.isol) c107e32 t107m32 s to-202 (n.isol) c107e4 t107m4 s to-202 (n.isol) c107e41 t107m41 s to-202 (n.isol) c107f t107b1 s to-202 (n.isol) c107f1 t107b1 s to-202 (n.isol) c107f11 t107b11 s to-202 (n.isol) c107f12 t107b12 s to-202 (n.isol) c107f2 t107b2 s to-202 (n.isol) c107f21 t107b21 s to-202 (n.isol) c107f3 t107b3 s to-202 (n.isol) c107f32 t107b32 s to-202 (n.isol) c107f4 t107b4 s to-202 (n.isol) c107f41 t107b41 s to-202 (n.isol) c107m t107m1 s to-202 (n.isol) c107m1 t107m1 s to-202 (n.isol) c107m11 t107m11 s to-202 (n.isol) c107m12 t107m12 s to-202 (n.isol) c107m2 t107m2 s to-202 (n.isol) c107m21 t107m21 s to-202 (n.isol) c107m3 t107m3 s to-202 (n.isol) c107m32 t107m32 s to-202 (n.isol) c107m41 t107m41 s to-202 (n.isol) c107q t107b1 s to-202 (n.isol) c107q1 t107b1 s to-202 (n.isol) c107q11 t107b11 s to-202 (n.isol) c107q12 t107b12 s to-202 (n.isol) c107q2 t107b2 s to-202 (n.isol) c107q21 t107b21 s to-202 (n.isol) c107q3 t107b3 s to-202 (n.isol) c107q32 t107b32 s to-202 (n.isol) c107q4 t107b4 s to-202 (n.isol) c107q41 t107b41 s to-202 (n.isol) c107y t107b1 s to-202 (n.isol) c107y1 t107b1 s to-202 (n.isol) c107y11 t107b11 s to-202 (n.isol) c107y12 t107b12 s to-202 (n.isol) c107y2 t107b2 s to-202 (n.isol) c107y21 t107b21 s to-202 (n.isol) c107y3 t107b3 s to-202 (n.isol) c107y32 t107b32 s to-202 (n.isol) c107y4 t107b4 s to-202 (n.isol) c107y41 t107b41 s to-202 (n.isol) c108a s2006fs21 s to-202 (n.isol) c108a1 s2006fs21 s to-202 (n.isol) c108a11 s2006fs211 s to-202 (n.isol) c108a12 s2006fs212 s to-202 (n.isol) c108a2 s2006fs22 s to-202 (n.isol) c108a21 s2006fs221 s to-202 (n.isol) c108a3 s2006fs23 s to-202 (n.isol) c108a32 s2006fs232 s to-202 (n.isol) c108a4 s2006fs24 s to-202 (n.isol) c108a41 s2006fs241 s to-202 (n.isol) c108b s2006fs21 s to-202 (n.isol) c108b1 s2006fs21 s to-202 (n.isol) c108b11 s2006fs211 s to-202 (n.isol) c108b12 s2006fs212 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-9 http://www.teccor.com thyristor product catalog +1 972-580-7777 c108b2 s2006fs22 s to-202 (n.isol) c108b21 s2006fs221 s to-202 (n.isol) c108b3 s2006fs23 s to-202 (n.isol) c108b32 s2006fs232 s to-202 (n.isol) c108b4 s2006fs24 s to-202 (n.isol) c108b41 s2006fs241 s to-202 (n.isol) c108c s4006fs21 s to-202 (n.isol) c108c1 s4006fs21 s to-202 (n.isol) c108c11 s4006fs211 s to-202 (n.isol) c108c12 s4006fs212 s to-202 (n.isol) c108c2 s4006fs22 s to-202 (n.isol) c108c21 s4006fs221 s to-202 (n.isol) c108c3 s4006fs23 s to-202 (n.isol) c108c32 s4006fs232 s to-202 (n.isol) c108c4 s4006fs24 s to-202 (n.isol) c108c41 s4006fs241 s to-202 (n.isol) c108d s4006fs21 s to-202 (n.isol) c108d1 s4006fs21 s to-202 (n.isol) c108d11 s4006fs211 s to-202 (n.isol) c108d12 s4006fs212 s to-202 (n.isol) c108d2 s4006fs22 s to-202 (n.isol) c108d21 s4006fs221 s to-202 (n.isol) c108d3 s4006fs23 s to-202 (n.isol) c108d32 s4006fs232 s to-202 (n.isol) c108d4 s4006fs24 s to-202 (n.isol) c108d41 s4006fs241 s to-202 (n.isol) c108e s6006fs21 s to-202 (n.isol) c108e1 s6006fs21 s to-202 (n.isol) c108e11 s6006fs211 s to-202 (n.isol) c108e12 s6006fs212 s to-202 (n.isol) c108e2 s6006fs22 s to-202 (n.isol) c108e21 s6006fs221 s to-202 (n.isol) c108e3 s6006fs23 s to-202 (n.isol) c108e32 s6006fs232 s to-202 (n.isol) c108e4 s6006fs24 s to-202 (n.isol) c108e41 s6006fs241 s to-202 (n.isol) c108f s2006fs21 s to-202 (n.isol) c108f1 s2006fs21 s to-202 (n.isol) c108f11 s2006fs211 s to-202 (n.isol) c108f12 s2006fs212 s to-202 (n.isol) c108f2 s2006fs22 s to-202 (n.isol) c108f21 s2006fs221 s to-202 (n.isol) c108f3 s2006fs23 s to-202 (n.isol) c108f32 s2006fs232 s to-202 (n.isol) c108f4 s2006fs24 s to-202 (n.isol) c108f41 s2006fs241 s to-202 (n.isol) c108m s6006fs21 s to-202 (n.isol) c108m1 s6006fs21 s to-202 (n.isol) c108m11 s6006fs211 s to-202 (n.isol) c108m12 s6006fs212 s to-202 (n.isol) c108m2 s6006fs22 s to-202 (n.isol) c108m21 s6006fs221 s to-202 (n.isol) c108m3 s6006fs23 s to-202 (n.isol) c108m32 s6006fs232 s to-202 (n.isol) c108m4 s6006fs24 s to-202 (n.isol) c108m41 s6006fs241 s to-202 (n.isol) c108q s2006fs21 s to-202 (n.isol) c108q1 s2006fs21 s to-202 (n.isol) c108q11 s2006fs211 s to-202 (n.isol) c108q12 s2006fs212 s to-202 (n.isol) c108q2 s2006fs22 s to-202 (n.isol) c108q21 s2006fs221 s to-202 (n.isol) c108q3 s2006fs23 s to-202 (n.isol) c108q32 s2006fs232 s to-202 (n.isol) c108q4 s2006fs24 s to-202 (n.isol) c108q41 s2006fs241 s to-202 (n.isol) c108y s2006fs21 s to-202 (n.isol) c108y1 s2006fs21 s to-202 (n.isol) c108y11 s2006fs211 s to-202 (n.isol) c108y12 s2006fs212 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package c108y2 s2006fs22 s to-202 (n.isol) c108y21 s2006fs221 s to-202 (n.isol) c108y3 s2006fs23 s to-202 (n.isol) c108y32 s2006fs232 s to-202 (n.isol) c108y4 s2006fs24 s to-202 (n.isol) c108y41 s2006fs241 s to-202 (n.isol) c116a1 s2008f1 s to-202 (n.isol) c116b1 s2008f1 s to-202 (n.isol) c116c1 s4008f1 s to-202 (n.isol) c116d1 s4008f1 s to-202 (n.isol) c116e1 s6008f1 s to-202 (n.isol) c116f1 s2008f1 s to-202 (n.isol) c116m1 s6008f1 s to-202 (n.isol) c122a s2008r s to-220 (n.isol) c122b s2008r s to-220 (n.isol) c122c s4008r s to-220 (n.isol) c122d s4008r s to-220 (n.isol) c122e s6008r s to-220 (n.isol) c122f s2008r s to-220 (n.isol) c122m s6008r s to-220 (n.isol) c122n s8008r s to-220 (n.isol) c122s s8008r s to-220 (n.isol) c123a s2008l s to-220 (isol) c123b s2008l s to-220 (isol) c123c s4008l s to-220 (isol) c123d s4008l s to-220 (isol) c123e s6008l s to-220 (isol) c123f s2008l s to-220 (isol) c123m s6008l s to-220 (isol) c126a s2012r s to-220 (n.isol) c126b s2012r s to-220 (n.isol) c126c s4012r s to-220 (n.isol) c126d s4012r s to-220 (n.isol) c126e s6012r s to-220 (n.isol) c126f s2012r s to-220 (n.isol) c126m s6012r s to-220 (n.isol) c127a s2016r d to-220 (n.isol) c127b s2016r d to-220 (n.isol) c127d s4016r d to-220 (n.isol) c127e s6016r d to-220 (n.isol) c127f s2016r d to-220 (n.isol) c127m s6016r d to-220 (n.isol) c203a ec103b s to-92 (isol) c203b ec103b s to-92 (isol) c203c ec103d s to-92 (isol) c203d ec103d s to-92 (isol) c203y ec103b s to-92 (isol) c203yy ec103b s to-92 (isol) c205a ec103b d to-92 (isol) c205b ec103b d to-92 (isol) c205c ec103d d to-92 (isol) c205d ec103d d to-92 (isol) c205y ec103b d to-92 (isol) c205yy ec103b d to-92 (isol) d30 ht32 d do-35 (isol) d40 ht40 d do-35 (isol) db3 ht32 s do-35 (isol) db4 ht40 d do-35 (isol) dc34 ht32 s do-35 (isol) dc38 ht40 s do-35 (isol) dc42 ht40 s do-35 (isol) do201yr ht5761 d do-35 (isol) hi03sc l2004f31 s to-202 (n.isol) hi03sd l2004f51 s to-202 (n.isol) hi03sg l2004f61 s to-202 (n.isol) hi03sh l2004f81 s to-202 (n.isol) hi03ss l2004f31 s to-202 (n.isol) hi13sc l2004f31 s to-202 (n.isol) hi13sd l2004f51 s to-202 (n.isol) hi13sg l2004f61 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-10 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog hi13sh l2004f81 s to-202 (n.isol) hi13ss l2004f31 s to-202 (n.isol) hi23sc l2004f31 s to-202 (n.isol) hi23sd l2004f51 s to-202 (n.isol) hi23sg l2004f61 s to-202 (n.isol) hi23sh l2004f81 s to-202 (n.isol) hi23ss l2004f31 s to-202 (n.isol) hi33sc l4004f31 s to-202 (n.isol) hi33sd l4004f51 s to-202 (n.isol) hi33sg l4004f61 s to-202 (n.isol) hi33sh l4004f81 s to-202 (n.isol) hi33ss l4004f31 s to-202 (n.isol) hi43sc l4004f31 s to-202 (n.isol) hi43sd l4004f51 s to-202 (n.isol) hi43sg l4004f61 s to-202 (n.isol) hi43sh l4004f81 s to-202 (n.isol) hi43ss l4004f31 s to-202 (n.isol) hi63sc l6004f31 s to-202 (n.isol) hi63sd l6004f51 s to-202 (n.isol) hi63sg l6004f61 s to-202 (n.isol) hi63sh l6004f81 s to-202 (n.isol) hi63ss l6004f31 s to-202 (n.isol) ht06 q2006f41 s to-202 (n.isol) ht16 q2006f41 s to-202 (n.isol) ht26 q2006f41 s to-202 (n.isol) ht36 q4006f41 s to-202 (n.isol) ht46 q4006f41 s to-202 (n.isol) ht66 q6006f41 s to-202 (n.isol) id100 ec103b s to-92 (isol) id101 ec103b s to-92 (isol) id102 ec103b s to-92 (isol) id103 ec103b s to-92 (isol) id104 ec103b s to-92 (isol) id105 ec103d s to-92 (isol) id106 ec103d s to-92 (isol) ip100 2n5064 d to-92 (isol) ip101 2n5064 d to-92 (isol) ip102 2n5064 d to-92 (isol) ip103 2n5064 d to-92 (isol) ip104 2n5064 d to-92 (isol) ip105 ec103d d to-92 (isol) ip106 ec103d d to-92 (isol) is010 s2010l d to-220 (isol) is010x s2010l d to-220 (isol) is020 s2020l s to-220 (isol) is020x s2020l d to-220 (isol) is08 s2008l d to-220 (isol) is08x s2008l d to-220 (isol) is110 s2010l d to-220 (isol) is110x s2010l d to-220 (isol) is120 s2020l s to-220 (isol) is120x s2020l d to-220 (isol) is18 s2008l d to-220 (isol) is18x s2008l d to-220 (isol) is210 s2010l d to-220 (isol) is210x s2010l d to-220 (isol) is220 s2020l s to-220 (isol) is220x s2020l d to-220 (isol) is28 s2008l d to-220 (isol) is28x s2008l d to-220 (isol) is310 s4010l d to-220 (isol) is310x s4010l d to-220 (isol) is320 s4020l s to-220 (isol) is320x s4020l d to-220 (isol) is38 s4008l d to-220 (isol) is38x s4008l d to-220 (isol) is410 s4010l d to-220 (isol) is410x s4010l d to-220 (isol) is420 s4020l s to-220 (isol) is420x s4020l d to-220 (isol) part number teccor device direct or suggested replacement teccor package is48 s4008l d to-220 (isol) is48x s4008l d to-220 (isol) is510 s6010l d to-220 (isol) is510x s6010l d to-220 (isol) is520 s6020l s to-220 (isol) is520x s6020l d to-220 (isol) is58 s6008l d to-220 (isol) is58x s6008l d to-220 (isol) is610 s6010l d to-220 (isol) is610x s6010l d to-220 (isol) is620 s6020l s to-220 (isol) is620x s6020l d to-220 (isol) is68 s6008l d to-220 (isol) is68x s6008l d to-220 (isol) it010 q2010l5 d to-220 (isol) it010a q2010l5 d to-220 (isol) it010b q2010l5 d to-220 (isol) it010ha q2010l5 s to-220 (isol) it010hx q2010l5 s to-220 (isol) it015 q2015l5 d to-220 (isol) it015a q2015l5 d to-220 (isol) it015b q2015l5 d to-220 (isol) it015ha q2015l5 s to-220 (isol) it015hx q2015l5 s to-220 (isol) it06 q2006l4 d to-220 (isol) it08 q2008l4 d to-220 (isol) it08a q2008l4 d to-220 (isol) it08b q2008l4 d to-220 (isol) it08ha q2008l4 d to-220 (isol) it08hx q2008l4 s to-220 (isol) it110 q2010l5 d to-220 (isol) it110a q2010l5 d to-220 (isol) it110b q2010l5 d to-220 (isol) it110ha q2010l5 s to-220 (isol) it110hx q2010l5 s to-220 (isol) it115 q2015l5 d to-220 (isol) it115a q2015l5 d to-220 (isol) it115b q2015l5 d to-220 (isol) it115ha q2015l5 s to-220 (isol) it115hx q2015l5 s to-220 (isol) it16 q2006l4 d to-220 (isol) it18 q2008l4 d to-220 (isol) it18a q2008l4 d to-220 (isol) it18b q2008l4 d to-220 (isol) it18ha q2008l4 d to-220 (isol) it18hx q2008l4 s to-220 (isol) it210 q2010l5 d to-220 (isol) it210a q2010l5 d to-220 (isol) it210b q2010l5 d to-220 (isol) it210ha q2010l5 s to-220 (isol) it210hx q2010l5 s to-220 (isol) it215 q2015l5 d to-220 (isol) it215a q2015l5 d to-220 (isol) it215b q2015l5 d to-220 (isol) it215ha q2015l5 s to-220 (isol) it215hx q2015l5 s to-220 (isol) it26 q2006l4 d to-220 (isol) it28 q2008l4 d to-220 (isol) it28a q2008l4 d to-220 (isol) it28b q2008l4 d to-220 (isol) it28ha q2008l4 d to-220 (isol) it28hx q2008l4 s to-220 (isol) it310 q4010l5 d to-220 (isol) it310a q4010l5 d to-220 (isol) it310b q4010l5 d to-220 (isol) it310ha q4010l5 s to-220 (isol) it310hx q4010l5 s to-220 (isol) it315 q4015l5 d to-220 (isol) it315a q4015l5 d to-220 (isol) it315b q4015l5 d to-220 (isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-11 http://www.teccor.com thyristor product catalog +1 972-580-7777 it315ha q4015l5 s to-220 (isol) it315hx q4015l5 s to-220 (isol) it36 q4006l4 d to-220 (isol) it38 q4008l4 d to-220 (isol) it38a q4008l4 d to-220 (isol) it38b q4008l4 d to-220 (isol) it38ha q4008l4 d to-220 (isol) it38hx q4008l4 s to-220 (isol) it410 q4010l5 d to-220 (isol) it410a q4010l5 d to-220 (isol) it410b q4010l5 d to-220 (isol) it410ha q4010l5 s to-220 (isol) it410hx q4010l5 s to-220 (isol) it415 q4015l5 d to-220 (isol) it415a q4015l5 d to-220 (isol) it415b q4015l5 d to-220 (isol) it415ha q4015l5 s to-220 (isol) it415hx q4015l5 s to-220 (isol) it46 q4006l4 d to-220 (isol) it48 q4008l4 d to-220 (isol) it48a q4008l4 d to-220 (isol) it48b q4008l4 d to-220 (isol) it48ha q4008l4 d to-220 (isol) it48hx q4008l4 s to-220 (isol) it510 q6010l5 d to-220 (isol) it510a q6010l5 d to-220 (isol) it510b q6010l5 d to-220 (isol) it510ha q6010l5 s to-220 (isol) it510hx q6010l5 s to-220 (isol) it515 q6015l5 d to-220 (isol) it515a q6015l5 d to-220 (isol) it515b q6015l5 d to-220 (isol) it515ha q6015l5 s to-220 (isol) it515hx q6015l5 s to-220 (isol) it56 q6006l4 d to-220 (isol) it58 q6008l4 d to-220 (isol) it58a q6008l4 d to-220 (isol) it58b q6008l4 d to-220 (isol) it58ha q6008l4 d to-220 (isol) it58hx q6008l4 s to-220 (isol) it610 q6010l5 d to-220 (isol) it610a q6010l5 d to-220 (isol) it610b q6010l5 d to-220 (isol) it610ha q6010l5 s to-220 (isol) it610hx q6010l5 s to-220 (isol) it615 q6015l5 d to-220 (isol) it615a q6015l5 d to-220 (isol) it615b q6015l5 d to-220 (isol) it615ha q6015l5 s to-220 (isol) it615hx q6015l5 s to-220 (isol) it66 q6006l5 d to-220 (isol) it68 q6008l5 d to-220 (isol) it68a q6008l5 d to-220 (isol) it68b q6008l5 d to-220 (isol) it68ha q6008l5 s to-220 (isol) it68hx q6008l5 s to-220 (isol) k1v10 k1050g s do-15x k1v11 k1100g s do-15x k1v12 k1200g s do-15x k1v14 k1300g s do-15x k1v16 k1500g s do-15x k1v18 k1500g s do-15x k1v22 k2200g s do-15x k1v24 k2400g s do-15x k1v26 k2500g s do-15x k1va10 k1050e70 s to-92 (isol) k1va11 k1100e70 s to-92 (isol) k1va12 k1200e70 s to-92 (isol) k1va14 k1300e70 s to-92 (isol) k1va16 k1500e70 s to-92 (isol) part number teccor device direct or suggested replacement teccor package l2004l7 l2004l6 d to-220 (isol) l2004l9 l2004l8 d to-220 (isol) l2006l7 l2006l6 d to-220 (isol) l2006l9 l2006l8 d to-220 (isol) l2008l7 l2008l6 d to-220 (isol) l2008l9 l2008l8 d to-220 (isol) l201e7 l201e6 d to-92 (isol) l201e9 l201e8 d to-92 (isol) l4004l7 l4004l6 d to-220 (isol) l4004l9 l4004l8 d to-220 (isol) l4006l7 l4006l6 d to-220 (isol) l4006l9 l4006l8 d to-220 (isol) l4008l7 l4008l6 d to-220 (isol) l4008l9 l4008l8 d to-220 (isol) l401e7 l401e6 d to-92 (isol) l401e9 l401e8 d to-92 (isol) l6004l7 l6004l6 d to-220 (isol) l6004l9 l6004l8 d to-220 (isol) l6006l7 l6006l6 d to-220 (isol) l6006l9 l6006l8 d to-220 (isol) l6008l7 l6008l6 d to-220 (isol) l6008l9 l6008l8 d to-220 (isol) l601e7 l601e6 d to-92 (isol) l601e9 l601e8 d to-92 (isol) mac08bt1 l2x5 s sot-223/compak mac08dt1 l4x5 s sot-223/compak mac08mt1 l6x5 s sot-223/compak mac12d q4015r5 s to-220 (n.isol) mac12hcd q4012rh5 s to-220 (n.isol) mac12hcm q6012rh5 s to-220 (n.isol) mac12hcn q8012rh5 s to-220 (n.isol) mac12m q6015r5 s to-220 (n.isol) mac12n q8015r5 s to-220 (n.isol) mac15-10 q8015r5 d to-220 (n.isol) mac15-10fp q8015l5 d to-220 (isol) mac15-4 q2015r5 d to-220 (n.isol) mac15-4fp q2015l5 d to-220 (isol) mac15-5 q4015r5 d to-220 (n.isol) mac15-6 q4015r5 d to-220 (n.isol) mac15-6fp q4015l5 d to-220 (isol) mac15-7 q6015r5 d to-220 (n.isol) mac15-8 q6015r5 d to-220 (n.isol) mac15-8fp q6015l5 d to-220 (isol) mac15-9 q8015r5 d to-220 (n.isol) mac15a10 q8015r5 s to-220 (n.isol) mac15a10fp q8015l5 s to-220 (isol) mac15a4 q2015r5 s to-220 (n.isol) mac15a4fp q2015l5 s to-220 (isol) mac15a5 q4015r5 s to-220 (n.isol) mac15a5fp q4015l5 s to-220 (isol) mac15a6 q4015r5 s to-220 (n.isol) mac15a6fp q4015l5 s to-220 (isol) mac15a7 q6015r5 s to-220 (n.isol) mac15a7fp q6015l5 s to-220 (isol) mac15a8 q6015r5 s to-220 (n.isol) mac15a8fp q6015l5 s to-220 (isol) mac15a9 q8015r5 s to-220 (n.isol) mac15a9fp q8015l5 s to-220 (isol) mac15m q6015r5 d to-220 (n.isol) mac15n q8015r5 d to-220 (n.isol) mac16-10 q8015r6 d to-220 (n.isol) mac16-4 q2015r6 d to-220 (n.isol) mac16-6 q4015r6 d to-220 (n.isol) mac16-8 q6015r6 d to-220 (n.isol) mac16cd q4015r6 s to-220 (n.isol) mac16cm q6015r6 s to-220 (n.isol) mac16cn q8015r6 s to-220 (n.isol) mac16d q4015r6 s to-220 (n.isol) mac16m q6015r6 s to-220 (n.isol) mac16n q8015r6 s to-220 (n.isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-12 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog mac20-10 q8025p5 s fastpak (isol) mac20-4 q6025p5 s fastpak (isol) mac20-5 q6025p5 s fastpak (isol) mac20-6 q6025p5 s fastpak (isol) mac20-7 q6025p5 s fastpak (isol) mac20-8 q6025p5 s fastpak (isol) mac20-9 q8025p5 s fastpak (isol) mac20a10 q8025p5 s fastpak (isol) mac20a4 q6025p5 s fastpak (isol) mac20a5 q6025p5 s fastpak (isol) mac20a6 q6025p5 s fastpak (isol) mac20a7 q6025p5 s fastpak (isol) mac20a8 q6025p5 s fastpak (isol) mac20a9 q8025p5 s fastpak (isol) mac210-10 q8010r5 d to-220 (n.isol) mac210-10fp q8010l5 d to-220 (isol) mac210-4 q2010r5 d to-220 (n.isol) mac210-4fp q2010l5 d to-220 (isol) mac210-5 q4010r5 d to-220 (n.isol) mac210-6 q4010r5 d to-220 (n.isol) mac210-6fp q4010l5 d to-220 (isol) mac210-7 q6010r5 d to-220 (n.isol) mac210-8 q6010r5 d to-220 (n.isol) mac210-8fp q6010l5 d to-220 (isol) mac210a10 q8010r5 s to-220 (n.isol) mac210a10f q8010l5 s to-220 (isol) mac210a4 q2010r5 s to-220 (n.isol) mac210a4fp q2010l5 s to-220 (isol) mac210a5 q4010r5 s to-220 (n.isol) mac210a5fp q4010l5 s to-220 (isol) mac210a6 q4010r5 s to-220 (n.isol) mac210a6fp q4010l5 s to-220 (isol) mac210a7 q6010r5 s to-220 (n.isol) mac210a7fp q6010l5 s to-220 (isol) mac210a8 q6010r5 s to-220 (n.isol) mac210a8fp q6010l5 s to-220 (isol) mac210a9 q8010r5 s to-220 (n.isol) mac210a9fp q8010l5 s to-220 (isol) mac212-10 q8012rh5 d to-220 (n.isol) mac212-10fp q8012lh5 d to-220 (isol) mac212-4 q2012rh5 d to-220 (n.isol) mac212-4fp q2012lh5 d to-220 (isol) mac212-6 q4012rh5 d to-220 (n.isol) mac212-6fp q4012lh5 d to-220 (isol) mac212-8 q6012rh5 d to-220 (n.isol) mac212-8fp q6012lh5 d to-220 (isol) mac212a10 q8012rh5 s to-220 (n.isol) mac212a10fp q8012lh5 s to-220 (isol) mac212a4 q2015rh5 s to-220 (n.isol) mac212a4fp q2012lh5 s to-220 (isol) mac212a6 q4012rh5 s to-220 (n.isol) mac212a6fp q4012lh5 s to-220 (isol) mac212a8 q6012rh5 s to-220 (n.isol) mac212a8fp q6012lh5 s to-220 (isol) mac213-10 q8012rh5 d to-220 (n.isol) mac213-4 q2012rh5 d to-220 (n.isol) mac213-6 q4012rh5 d to-220 (n.isol) mac213-8 q6012rh5 d to-220 (n.isol) mac218-10 q8008r5 d to-220 (n.isol) mac218-10fp q8008l5 d to-220 (isol) mac218-2 q2008r5 d to-220 (n.isol) mac218-3 q2008r5 d to-220 (n.isol) mac218-4 q2008r5 d to-220 (n.isol) mac218-4fp q2008l5 d to-220 (isol) mac218-5 q4008r4 d to-220 (n.isol) mac218-6 q4008r4 d to-220 (n.isol) mac218-6fp q4008l5 d to-220 (isol) mac218-7 q4008r4 d to-220 (n.isol) mac218-8 q6008r5 d to-220 (n.isol) mac218-8fp q6008l5 s to-220 (isol) part number teccor device direct or suggested replacement teccor package mac218-a10 q8008r5 s to-220 (n.isol) mac218-a10fp q8008l5 s to-220 (isol) mac218-a2 q2008r4 s to-220 (n.isol) mac218-a3 q2008r4 s to-220 (n.isol) mac218-a4 q2008r4 s to-220 (n.isol) mac218-a4fp q2008l4 s to-220 (isol) mac218-a5 q4008r4 s to-220 (n.isol) mac218-a6 q4008r4 s to-220 (n.isol) mac218-a6fp q4008l4 s to-220 (isol) mac218-a7 q5008r4 s to-220 (n.isol) mac218-a8 q6008r5 s to-220 (n.isol) mac218-a8fp q6008l5 s to-220 (isol) mac219-10 q8008r5 d to-220 (n.isol) mac219-4 q2008r4 d to-220 (n.isol) mac219-6 q4008r4 d to-220 (n.isol) mac219-8 q6008r5 d to-220 (n.isol) mac220-2 q2008r4 d to-220 (n.isol) mac220-3 q2008r4 d to-220 (n.isol) mac220-5 q4008r4 d to-220 (n.isol) mac220-7 q6008r4 d to-220 (n.isol) mac220-9 q8008r5 d to-220 (n.isol) mac221-2 q2008r4 d to-220 (n.isol) mac221-3 q2008r4 d to-220 (n.isol) mac221-5 q4008r4 d to-220 (n.isol) mac221-7 q6008r4 d to-220 (n.isol) mac221-9 q8008r5 d to-220 (n.isol) mac222-1 q2008r4 d to-220 (n.isol) mac222-10 q8008r5 d to-220 (n.isol) mac222-2 q2008r4 d to-220 (n.isol) mac222-3 q2008r4 d to-220 (n.isol) mac222-4 q2008r4 d to-220 (n.isol) mac222-5 q4008r4 d to-220 (n.isol) mac222-6 q4008r4 d to-220 (n.isol) mac222-7 q6008r4 d to-220 (n.isol) mac222-8 q6008r5 d to-220 (n.isol) mac222-9 q8008r5 d to-220 (n.isol) mac222a1 q2008r4 s to-220 (n.isol) mac222a10 q8008r5 s to-220 (n.isol) mac222a2 q2008r4 s to-220 (n.isol) mac222a3 q2008r4 s to-220 (n.isol) mac222a4 q2008r4 s to-220 (n.isol) mac222a5 q4008r4 s to-220 (n.isol) mac222a6 q4008r4 s to-220 (n.isol) mac222a7 q6008r4 s to-220 (n.isol) mac222a8 q6008r5 s to-220 (n.isol) mac222a9 q8008r5 s to-220 (n.isol) mac223-10 q8025r5 s to-220 (n.isol) mac223-10fp q8025l6 s to-220 (isol) mac223-3 q2025r5 s to-220 (n.isol) mac223-4 q2025r5 s to-220 (n.isol) mac223-4fp q2025l6 s to-220 (isol) mac223-5 q4025r5 s to-220 (n.isol) mac223-6 q4025r5 s to-220 (n.isol) mac223-6fp q4025l6 s to-220 (isol) mac223-7 q6025r5 s to-220 (n.isol) mac223-8 q6025r5 s to-220 (n.isol) mac223-8fp q6025l6 s to-220 (isol) mac223-9 q8025r5 s to-220 (n.isol) mac223a10 q8025r5 s to-220 (n.isol) mac223a10fp q8025l6 s to-220 (isol) mac223a3 q4025r5 s to-220 (n.isol) mac223a4 q2025r5 s to-220 (n.isol) mac223a4fp q2025l6 s to-220 (isol) mac223a5 q4025r5 s to-220 (n.isol) mac223a5fp q4025l6 s to-220 (isol) mac223a6 q4025r5 s to-220 (n.isol) mac223a6fp q4025l6 s to-220 (isol) mac223a7 q6025r5 s to-220 (n.isol) mac223a7fp q6025l6 s to-220 (isol) mac223a8 q6025r5 s to-220 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-13 http://www.teccor.com thyristor product catalog +1 972-580-7777 mac223a8fp q6025l6 s to-220 (isol) mac223a9 q8025r5 s to-220 (n.isol) mac223a9fp q8025l6 s to-220 (isol) mac224-10 q8040k7 s to-218 (isol) mac224-4 q2040k7 s to-218 (isol) mac224-5 q4040k7 s to-218 (isol) mac224-6 q4040k7 s to-218 (isol) mac224-7 q6040k7 s to-218 (isol) mac224-8 q6040k7 s to-218 (isol) mac224a10 q8040k7 s to-218 (isol) mac224a4 q2040k7 s to-218 (isol) mac224a5 q4040k7 s to-218 (isol) mac224a6 q4040k7 s to-218 (isol) mac224a7 q6040k7 s to-218 (isol) mac224a8 q6040k7 s to-218 (isol) mac224a9 q8040k7 s to-218 (isol) mac228-2 l2008l6 s to-220 (isol) mac228-3 l2008l6 s to-220 (isol) mac228-4 l2008l6 s to-220 (isol) mac228-4fp l2008l6 d to-220 (isol) mac228-5 l4008l6 s to-220 (isol) mac228-6 l4008l6 s to-220 (isol) mac228-6fp l4008l6 d to-220 (isol) mac228-7 l6008l6 s to-220 (isol) mac228-8 l6008l6 s to-220 (isol) mac228-8fp l6008l6 d to-220 (isol) mac228a2 l2008l6 s to-220 (isol) mac228a3 l2008l6 s to-220 (isol) mac228a4 l2008l6 s to-220 (isol) mac228a4fp l2008l6 s to-220 (isol) mac228a5 l4008l6 s to-220 (isol) mac228a6 l4008l6 s to-220 (isol) mac228a6fp l4008l6 s to-220 (isol) mac228a7 l6008l6 s to-220 (isol) mac228a8 l6008l6 s to-220 (isol) mac228a8fp l6008l6 s to-220 (isol) mac229-4 l2008l6 s to-220 (isol) mac229-4fp l2008l6 d to-220 (isol) mac229-6 l4008l6 s to-220 (isol) mac229-6fp l4008l6 d to-220 (isol) mac229-8 l6008l6 s to-220 (isol) mac229-8fp l6008l6 d to-220 (isol) mac229a4 l2008l6 s to-220 (isol) mac229a4fp l2008l6 s to-220 (isol) mac229a6 l4008l6 s to-220 (isol) mac229a6fp l4008l6 s to-220 (isol) mac229a8 l6008l6 s to-220 (isol) mac229a8fp l6008l6 s to-220 (isol) mac229a8fp l6008l6 s to-220 (isol) mac25-10 q8025p5 s fastpak (isol) mac25-4 q6025p5 s fastpak (isol) mac25-5 q6025p5 s fastpak (isol) mac25-6 q6025p5 s fastpak (isol) mac25-7 q6025p5 s fastpak (isol) mac25-8 q6025p5 s fastpak (isol) mac25-9 q8025p5 s fastpak (isol) mac25a10 q8025p5 s fastpak (isol) mac25a4 q6025p5 s fastpak (isol) mac25a5 q6025p5 s fastpak (isol) mac25a6 q6025p5 s fastpak (isol) mac25a7 q6025p5 s fastpak (isol) mac25a8 q6025p5 s fastpak (isol) mac25a9 q8025p5 s fastpak (isol) mac3010-15 q2015r5 s to-220 (n.isol) mac3010-25 q2025r5 s to-220 (n.isol) mac3010-4 l2004f31 s to-202 (n.isol) mac3010-8 q2008r4 d to-220 (n.isol) mac3020-15 q4015r5 s to-220 (n.isol) mac3020-25 q4025r5 s to-220 (n.isol) mac3020-4 l4004f31 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package mac3020-8 q4008r4 d to-220 (n.isol) mac3030-15 q2015r5 s to-220 (n.isol) mac3030-25 q2025r5 s to-220 (n.isol) mac3030-4 l4004f41 s to-202 (n.isol) mac3030-8 q2008r4 d to-220 (n.isol) mac3040-15 q4015r5 s to-220 (n.isol) mac3040-25 q4025r5 s to-220 (n.isol) mac3040-4 l4004f41 s to-202 (n.isol) mac3040-8 q4008r4 d to-220 (n.isol) mac320-10 q8025r5 s to-220 (n.isol) mac320-10fp q8025l6 s to-220 (isol) mac320-4 q2025r5 s to-220 (n.isol) mac320-4fp q2025l6 s to-220 (isol) mac320-6 q4025r5 s to-220 (n.isol) mac320-6fp q4025l6 s to-220 (isol) mac320-8 q6025r5 s to-220 (n.isol) mac320-8fp q6025l6 s to-220 (isol) mac320a10 q8025r5 s to-220 (n.isol) mac320a4 q2025r5 s to-220 (n.isol) mac320a6 q4025r5 s to-220 (n.isol) mac320a8 q6025r5 s to-220 (n.isol) mac321-10 q8025r5 d to-220 (n.isol) mac321-4 q2025r5 d to-220 (n.isol) mac321-6 q4025r5 d to-220 (n.isol) mac321-8 q6025r5 d to-220 (n.isol) mac4dcm q6006dh4 s to-252 (smt) mac4dcm1 q6006vh4 s to-251 (n.isol) mac4dcn q8006dh4 s to-252 (smt) mac4dcn1 q8006vh4 s to-251 (n.isol) mac4dhm l6004d6 s to-252 (smt) mac4dhm1 l6004v6 s to-251 (n.isol) mac4dlm l6004d5 s to-252 (smt) mac4dlm1 l6004v5 s to-251 (n.isol) mac4dsm q6006dh3 s to-252 (smt) mac4dsm1 q6006vh3 s to-251 (n.isol) mac4dsn q8006dh3 s to-252 (smt) mac4dsn1 q8006vh3 s to-251 (n.isol) mac50-4 q6035p5 s fastpak (isol) mac50-5 q6035p5 s fastpak (isol) mac50-6 q6035p5 s fastpak (isol) mac50-7 q6035p5 s fastpak (isol) mac50-8 q6035p5 s fastpak (isol) mac50-9 q8035p5 s fastpak (isol) mac50a4 q6035p5 s fastpak (isol) mac50a5 q6035p5 s fastpak (isol) mac50a6 q6035p5 s fastpak (isol) mac50a7 q6035p5 s fastpak (isol) mac50a8 q6035p5 s fastpak (isol) mac50a9 q8035p5 s fastpak (isol) mac515-10 q8025p5 s fastpak (isol) mac515-4 q6025p5 s fastpak (isol) mac515-5 q6025p5 s fastpak (isol) mac515-6 q6025p5 s fastpak (isol) mac515-7 q6025p5 s fastpak (isol) mac515-8 q6025p5 s fastpak (isol) mac515-9 q8025p5 s fastpak (isol) mac515a10 q8025p5 s fastpak (isol) mac515a4 q6025p5 s fastpak (isol) mac515a5 q6025p5 s fastpak (isol) mac515a6 q6025p5 s fastpak (isol) mac515a7 q6025p5 s fastpak (isol) mac515a8 q6025p5 s fastpak (isol) mac515a9 q8025p5 s fastpak (isol) mac525-10 q8025p5 s fastpak (isol) mac525-4 q6025p5 s fastpak (isol) mac525-5 q6025p5 s fastpak (isol) mac525-6 q6025p5 s fastpak (isol) mac525-7 q6025p5 s fastpak (isol) mac525-8 q6025p5 s fastpak (isol) mac525-9 q8025p5 s fastpak (isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-14 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog mac525a10 q8025p5 s fastpak (isol) mac525a4 q6025p5 s fastpak (isol) mac525a5 q6025p5 s fastpak (isol) mac525a6 q6025p5 s fastpak (isol) mac525a7 q6025p5 s fastpak (isol) mac525a8 q6025p5 s fastpak (isol) mac525a9 q8025p5 s fastpak (isol) mac625-4 q6025p5 s fastpak (isol) mac625-6 q6025p5 s fastpak (isol) mac625-8 q6025p5 s fastpak (isol) mac635-4 q6035p5 s fastpak (isol) mac635-6 q6035p5 s fastpak (isol) mac635-8 q6035p5 s fastpak (isol) mac8d q4008rh4 d to-220 (n.isol) mac8m q6008rh4 d to-220 (n.isol) mac8n q8008rh4 d to-220 (n.isol) mac91-1 q2x8e3 d to-92 (isol) mac91-2 q2x8e3 d to-92 (isol) mac91-3 q2x8e3 d to-92 (isol) mac91-4 q2x8e3 d to-92 (isol) mac91-5 q4x8e3 d to-92 (isol) mac91-6 q4x8e3 d to-92 (isol) mac91-7 q5x8e3 d to-92 (isol) mac91-8 q6x8e3 d to-92 (isol) mac91a1 l2x8e6 d to-92 (isol) mac91a2 l2x8e6 d to-92 (isol) mac91a3 l2x8e6 d to-92 (isol) mac91a4 l2x8e6 d to-92 (isol) mac91a5 l4x8e6 d to-92 (isol) mac91a6 l4x8e6 d to-92 (isol) mac91a7 l6x8e6 d to-92 (isol) mac91a8 l6x8e6 d to-92 (isol) mac92-1 l2x8e5 d to-92 (isol) mac92-2 l2x8e5 d to-92 (isol) mac92-3 l2x8e5 d to-92 (isol) mac92-4 l2x8e5 d to-92 (isol) mac92-5 l4x8e5 d to-92 (isol) mac92-6 l4x8e5 d to-92 (isol) mac92-7 l6x8e5 d to-92 (isol) mac92-8 l6x8e5 d to-92 (isol) mac92a1 l2x8e5 d to-92 (isol) mac92a2 l2x8e5 d to-92 (isol) mac92a3 l2x8e5 d to-92 (isol) mac92a4 l2x8e5 d to-92 (isol) mac92a5 l4x8e5 d to-92 (isol) mac92a6 l4x8e5 d to-92 (isol) mac92a7 l6x8e5 d to-92 (isol) mac92a8 l6x8e5 d to-92 (isol) mac93-1 l2x8e3 d to-92 (isol) mac93-2 l2x8e3 d to-92 (isol) mac93-3 l2x8e3 d to-92 (isol) mac93-4 l2x8e3 d to-92 (isol) mac93-5 l4x8e3 d to-92 (isol) mac93-6 l4x8e3 d to-92 (isol) mac93-7 l6x8e3 d to-92 (isol) mac93-8 l6x8e3 d to-92 (isol) mac93a1 q2x8e3 d to-92 (isol) mac93a2 q2x8e3 d to-92 (isol) mac93a3 q2x8e3 d to-92 (isol) mac93a4 q2x8e3 d to-92 (isol) mac93a5 l4x8e3 d to-92 (isol) mac93a6 l4x8e3 d to-92 (isol) mac93a7 l6x8e3 d to-92 (isol) mac93a8 l6x8e3 d to-92 (isol) mac94-1 q2x8e3 d to-92 (isol) mac94-2 q2x8e3 d to-92 (isol) mac94-3 q2x8e3 d to-92 (isol) mac94-4 q2x8e3 d to-92 (isol) mac94-5 q4x8e3 d to-92 (isol) mac94-6 q4x8e3 d to-92 (isol) part number teccor device direct or suggested replacement teccor package mac94-7 q6x8e3 d to-92 (isol) mac94-8 q6x8e3 d to-92 (isol) mac94a1 l2x8e6 d to-92 (isol) mac94a2 l2x8e6 d to-92 (isol) mac94a3 l2x8e6 d to-92 (isol) mac94a4 l2x8e6 d to-92 (isol) mac94a5 l4x8e6 d to-92 (isol) mac94a6 l4x8e6 d to-92 (isol) mac94a7 l6x8e6 d to-92 (isol) mac94a8 l6x8e6 d to-92 (isol) mac95-1 l2x8e5 d to-92 (isol) mac95-2 l2x8e5 d to-92 (isol) mac95-3 l2x8e5 d to-92 (isol) mac95-4 l2x8e5 d to-92 (isol) mac95-5 l4x8e5 d to-92 (isol) mac95-6 l4x8e5 d to-92 (isol) mac95-7 l6x8e5 d to-92 (isol) mac95-8 l6x8e5 d to-92 (isol) mac95a1 l2x8e5 d to-92 (isol) mac95a2 l2x8e5 d to-92 (isol) mac95a3 l2x8e5 d to-92 (isol) mac95a4 l2x8e5 d to-92 (isol) mac95a5 l4x8e5 d to-92 (isol) mac95a6 l4x8e5 d to-92 (isol) mac95a7 l6x8e5 d to-92 (isol) mac95a8 l6x8e5 d to-92 (isol) mac96-1 l2x8e3 d to-92 (isol) mac96-2 l2x8e3 d to-92 (isol) mac96-3 l2x8e3 d to-92 (isol) mac96-4 l2x8e3 d to-92 (isol) mac96-5 l4x8e3 d to-92 (isol) mac96-6 l4x8e3 d to-92 (isol) mac96-7 l6x8e3 d to-92 (isol) mac96-8 l6x8e3 d to-92 (isol) mac96a1 l2x8e3 d to-92 (isol) mac96a2 l2x8e3 d to-92 (isol) mac96a3 l2x8e3 d to-92 (isol) mac96a4 l2x8e3 d to-92 (isol) mac96a5 l4x8e3 d to-92 (isol) mac96a6 l4x8e3 d to-92 (isol) mac96a7 l6x8e3 d to-92 (isol) mac96a8 l6x8e3 d to-92 (isol) mac97-2 l2x8e6 d to-92 (isol) mac97-3 l2x8e6 d to-92 (isol) mac97-4 l2x8e6 d to-92 (isol) mac97-5 l4x8e6 d to-92 (isol) mac97-6 l4x8e6 d to-92 (isol) mac97-7 l6x8e6 d to-92 (isol) mac97-8 l6x8e6 d to-92 (isol) mac97a2 l2x8e5 d to-92 (isol) mac97a3 l2x8e5 d to-92 (isol) mac97a4 l2x8e5 d to-92 (isol) mac97a5 l4x8e5 d to-92 (isol) mac97a6 l4x8e5 d to-92 (isol) mac97a7 l6x8e5 d to-92 (isol) mac97a8 l6x8e5 d to-92 (isol) mac97b2 l2x8e3 d to-92 (isol) mac97b3 l2x8e3 d to-92 (isol) mac97b4 l2x8e3 d to-92 (isol) mac97b5 l4x8e3 d to-92 (isol) mac97b6 l4x8e3 d to-92 (isol) mac97b7 l6x8e3 d to-92 (isol) mac97b8 l6x8e3 d to-92 (isol) mac9d q4008rh4 s to-220 (n.isol) mac9m q6008rh4 s to-220 (n.isol) mac9n q8008rh4 s to-220 (n.isol) mcr08bt1 s2s s sot-223 / compak mcr08dt1 s4s s sot-223 / compak mcr08mt1 s6s s sot-223 / compak mcr100-3 ec103b d to-92 (isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-15 http://www.teccor.com thyristor product catalog +1 972-580-7777 mcr100-4 ec103b d to-92 (isol) mcr100-5 ec103d d to-92 (isol) mcr100-6 ec103d d to-92 (isol) mcr100-7 ec103m d to-92 (isol) mcr100-8 ec103m d to-92 (isol) mcr101 ec103b d to-92 (isol) mcr102 ec103b d to-92 (isol) mcr103 ec103b d to-92 (isol) mcr106-1 t106b1 d to-202 (n.isol) mcr106-2 t106b1 d to-202 (n.isol) mcr106-3 t106b1 d to-202 (n.isol) mcr106-4 t106b1 d to-202 (n.isol) mcr106-5 t106d1 d to-202 (n.isol) mcr106-6 t106d1 d to-202 (n.isol) mcr106-7 t106m1 d to-202 (n.isol) mcr106-8 t106m1 d to-202 (n.isol) mcr120 ec103b d to-92 (isol) mcr12dsm s6010ds2 s to-252 (smt) mcr12dsm1 s6010vs2 s to-251 (n.isol) mcr12m q6015r s to-220 (n.isol) mcr12n q8015r s to-220 (n.isol) mcr16d q4015r s to-220 (n.isol) mcr16m q6015r s to-220 (n.isol) mcr16n q8015r s to-220 (n.isol) mcr202 ec103b s to-92 (isol) mcr203 ec103b s to-92 (isol) mcr204 ec103b s to-92 (isol) mcr206 ec103b s to-92 (isol) mcr218-10fp s8008l d to-220 (isol) mcr218-2 s2008r d to-220 (n.isol) mcr218-2fp s2008l d to-220 (isol) mcr218-3 s2008r d to-220 (n.isol) mcr218-3fp s2008l d to-220 (isol) mcr218-4 s2008r d to-220 (n.isol) mcr218-4fp s2008l d to-220 (isol) mcr218-5 s4008r d to-220 (n.isol) mcr218-6 s4008r d to-220 (n.isol) mcr218-6fp s4008l d to-220 (isol) mcr218-7 s6008r d to-220 (n.isol) mcr218-8 s6008r d to-220 (n.isol) mcr218-8fp s6008l d to-220 (isol) mcr220-5 s4012r d to-220 (n.isol) mcr220-7 s6012r d to-220 (n.isol) mcr220-9 s8012r d to-220 (n.isol) mcr22-1 tcr22-4 s to-92 (isol) mcr221-5 s4016r d to-220 (n.isol) mcr221-7 s6016r d to-220 (n.isol) mcr221-9 s8016r d to-220 (n.isol) mcr22-2 tcr22-4 d to-92 (isol) mcr22-3 tcr22-4 d to-92 (isol) mcr22-4 tcr22-4 d to-92 (isol) mcr225-10fp s8025l s to-220 (isol) mcr225-2fp s2025l s to-220 (isol) mcr225-4fp s2025l s to-220 (isol) mcr225-5 s4025r s to-220 (n.isol) mcr225-6fp s4025l s to-220 (isol) mcr225-7 s6025r s to-220 (n.isol) mcr225-8fp s6025l s to-220 (isol) mcr225-9 s8025r s to-220 (n.isol) mcr22-6 tcr22-6 d to-92 (isol) mcr22-7 tcr22-8 d to-92 (isol) mcr22-8 tcr22-8 d to-92 (isol) mcr25d s4025r d to-220 (n.isol) mcr25m s6025r d to-220 (n.isol) mcr25n s8025r d to-220 (n.isol) mcr264-10 s8040r d to-220 (n.isol) mcr264-2 s2040r d to-220 (n.isol) mcr264-3 s2040r d to-220 (n.isol) mcr264-4 s2040r d to-220 (n.isol) mcr264-6 s4040r d to-220 (n.isol) part number teccor device direct or suggested replacement teccor package mcr264-8 s6040r d to-220 (n.isol) mcr265-10 s8055r d to-220 (n.isol) mcr265-2 s2055r d to-220 (n.isol) mcr265-3 s2055r d to-220 (n.isol) mcr265-4 s2055r d to-220 (n.isol) mcr265-6 s4055r d to-220 (n.isol) mcr265-8 s6055r d to-220 (n.isol) mcr3000-1 s2008r s to-220 (n.isol) mcr3000-10 s8008r s to-220 (n.isol) mcr3000-2 s2008r s to-220 (n.isol) mcr3000-3 s2008r s to-220 (n.isol) mcr3000-4 s2008r s to-220 (n.isol) mcr3000-5 s4008r s to-220 (n.isol) mcr3000-6 s4008r s to-220 (n.isol) mcr3000-7 s6008r s to-220 (n.isol) mcr3000-8 s6008r s to-220 (n.isol) mcr3000-9 s8008r s to-220 (n.isol) mcr310-1 s2010ls2 s to-220 (isol) mcr310-2 s2010ls2 s to-220 (isol) mcr310-3 s2010ls2 s to-220 (isol) mcr310-4 s2010ls2 s to-220 (isol) mcr310-5 s4010ls2 s to-220 (isol) mcr310-6 s4010ls2 s to-220 (isol) mcr310-7 s6010ls2 s to-220 (isol) mcr310-8 s6010ls2 s to-220 (isol) mcr506-1 s2006fs21 s to-202 (n.isol) mcr506-2 s2006fs21 s to-202 (n.isol) mcr506-3 s2006fs21 s to-202 (n.isol) mcr506-4 s2006fs21 s to-202 (n.isol) mcr506-6 s4006fs21 s to-202 (n.isol) mcr506-8 s6006fs21 s to-202 (n.isol) mcr525-1 s2035j s to-218 (isol) mcr525-2 s2035j s to-218 (isol) mcr525-3 s2035j s to-218 (isol) mcr525-6 s4035j s to-218 (isol) mcr68-1 s2012r d to-220 (n.isol) mcr68-2 s2012r d to-220 (n.isol) mcr68-3 s2012r d to-220 (n.isol) mcr68-6 s4012r d to-220 (n.isol) mcr69-1 s2025r d to-220 (n.isol) mcr69-2 s2025r d to-220 (n.isol) mcr69-3 s2025r d to-220 (n.isol) mcr69-6 s4025r d to-220 (n.isol) mcr704a s2004ds2 s to-252 (smt) mcr704a1 s2004vs2 s to-251 (n.isol) mcr706a s4004ds2 s to-252 (smt) mcr706a1 s4004vs2 s to-251 (n.isol) mcr708a s6004ds2 s to-252 (smt) mcr708a1 s6004vs2 s to-251 (n.isol) mcr716 s4004ds2 d to-252 (smt) mcr718 s6004ds2 d to-252 (smt) mcr72-1 s2008ls2 s to-220 (isol) mcr72-2 s2008ls2 s to-220 (isol) mcr72-3 s2008ls2 s to-220 (isol) mcr72-4 s2008ls2 s to-220 (isol) mcr72-5 s4008ls2 s to-220 (isol) mcr72-6 s4008ls2 s to-220 (isol) mcr72-7 s6008ls2 s to-220 (isol) mcr72-8 s6008ls2 s to-220 (isol) mcr8dcm s6008d d to-252 (smt) mcr8dcm1 s6008v d to-251 (n.isol) mcr8dcn s8008d d to-252 (smt) mcr8dcn1 s8008v d to-251 (n.isol) mcr8dsm s6008ds2 d to-252 (smt) mcr8dsm1 s6008vs2 d to-251 (n.isol) mcr8sd s4008fs21 s to-202 (n.isol) mcr8sm s6008fs21 s to-202 (n.isol) mk1v115 k1100g s do-15x mk1v125 k1200g s do-15x mk1v135 k1300g s do-15x part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-16 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog mk1v240 k2400g s do-15x mk1v260 k2500g s do-15x mk1v270 k2500g s do-15x mk1v280 k2500g s do-15x mkp1v120 k1200e70 s to-92 (isol) mkp1v130 k1300e70 s to-92 (isol) mkp1v240 k2400e70 s to-92 (isol) mkp3v110 k1100g s do-15x mkp3v120 k1200g s do-15x mkp3v130 k1300g s do-15x mkp9v120 k1200e70 s to-92 (isol) mkp9v130 k1300e70 s to-92 (isol) mkp9v240 k2400e70 s to-92 (isol) mkp9v260 k2500e70 s to-92 (isol) mkp9v270 k2500e70 s to-92 (isol) mn611a k1050e70 s to-92 (isol) p0100aa ec103b1 d to-92 (isol) p0100ab ec103b1 s to-92 (isol) p0100ba ec103b1 d to-92 (isol) p0100bb ec103b1 s to-92 (isol) p0100ca ec103d1 d to-92 (isol) p0100cb ec103d1 s to-92 (isol) p0100da ec103d1 d to-92 (isol) p0100db ec103d1 s to-92 (isol) p0101aa ec103b1 d to-92 (isol) p0101ab ec103b1 s to-92 (isol) p0101ba ec103b1 d to-92 (isol) p0101bb ec103b1 s to-92 (isol) p0101ca ec103d1 d to-92 (isol) p0101cb ec103d1 s to-92 (isol) p0101da ec103d1 d to-92 (isol) p0101db ec103d1 s to-92 (isol) p0102aa ec103b d to-92 (isol) p0102ab ec103b s to-92 (isol) p0102ad ec103b78 s to-92 (isol) p0102an s2s s sot223/compak p0102ba ec103b d to-92 (isol) p0102bb ec103b s to-92 (isol) p0102bd ec103b78 s to-92 (isol) p0102bn s2s s sot223/compak p0102ca ec103d d to-92 (isol) p0102cb ec103d s to-92 (isol) p0102cd ec103d78 s to-92 (isol) p0102cn s4s s sot223/compak p0102da ec103d d to-92 (isol) p0102db ec103d s to-92 (isol) p0102dd ec103d78 s to-92 (isol) p0102dn s4s s sot223/compak p0103aa ec103b d to-92 (isol) p0103ab ec103b s to-92 (isol) p0103ba ec103b d to-92 (isol) p0103bb ec103b s to-92 (isol) p0103ca ec103d d to-92 (isol) p0103cb ec103d s to-92 (isol) p0103da ec103d d to-92 (isol) p0103db ec103d s to-92 (isol) p0104aa ec103b2 d to-92 (isol) p0104ab ec103b2 s to-92 (isol) p0104ba ec103b2 d to-92 (isol) p0104bb ec103b2 s to-92 (isol) p0104ca ec103d2 d to-92 (isol) p0104cb ec103d2 s to-92 (isol) p0104da ec103d2 d to-92 (isol) p0104db ec103d2 s to-92 (isol) p0105aa ec103b2 s to-92 (isol) p0105ab ec103b2 s to-92 (isol) p0105ba ec103b2 s to-92 (isol) p0105bb ec103b2 d to-92 (isol) p0105ca ec103d2 s to-92 (isol) p0105cb ec103d2 s to-92 (isol) part number teccor device direct or suggested replacement teccor package p0105da ec103d2 s to-92 (isol) p0105db ec103d2 s to-92 (isol) p0110aa ec103b1 s to-92 (isol) p0110ab ec103b1 s to-92 (isol) p0110ba ec103b1 s to-92 (isol) p0110bb ec103b2 s to-92 (isol) p0110ca ec103d2 s to-92 (isol) p0110cb ec103d1 s to-92 (isol) p0110da ec103d1 s to-92 (isol) p0110db ec103d1 s to-92 (isol) p0111an s2s1 s sot223/compak p0111bn s2s1 s sot223/compak p0111cn s4s1 s sot223/compak p0111dn s4s1 s sot223/compak pt20 d2015l d to-220 (isol) pt40 d4015l d to-220 (isol) pt60 d6015l d to-220 (isol) q2015l9 q2016lh6 d to-220 (isol) q2015r9 q2016rh6 d to-220 (n.isol) q2025l9 q2025l6 s to-220 (isol) q2025r9 q2025r6 s to-220 (n.isol) q2040j9 q2040j7 d to-218x (isol) q2040k9 q2040k7 d to-218ac (isol) q4015l9 q4016lh6 d to-220 (isol) q4015r9 q4016rh6 d to-220 (n.isol) q4025l9 q4025l6 s to-220 (isol) q4025r9 q4025r6 s to-220 (n.isol) q4040j9 q4040j7 d to-218x (isol) q4040k9 q4040k7 d to-218ac (isol) q5015l9 q6016lh6 d to-220 (isol) q5015r9 q6016rh6 d to-220 (n.isol) q5025l9 q6025l6 s to-220 (isol) q5025r9 q6025r6 s to-220 (n.isol) q5040j9 q6040j7 d to-218x (isol) q5040k9 q6040k7 d to-218ac (isol) q6015l9 q6016lh6 d to-220 (isol) q6015r9 q6016rh6 d to-220 (n.isol) q6025l9 q6025l6 s to-220 (isol) q6025r9 q6025r6 s to-220 (n.isol) q6040j9 q6040j7 d to-218x (isol) q6040k9 q6040k7 d to-218ac (isol) q7015l9 q8016lh6 d to-220 (isol) q7015r9 q8016rh6 d to-220 (n.isol) q7025l9 q8025l6 s to-220 (isol) q7025r9 q8025r6 s to-220 (n.isol) q7040j9 q8040j7 d to-218x (isol) q7040k9 q8040k7 d to-218ac (isol) q8015l9 q8016lh6 d to-220 (isol) q8015r9 q8016rh6 d to-220 (n.isol) q8025l9 q8025l6 s to-220 (isol) q8025r9 q8025r6 s to-220 (n.isol) q8040j9 q8040j7 d to-218x (isol) q8040k9 q8040k7 d to-218ac (isol) s0402bh t106b1 s to-202 (n.isol) s0402dh t106d1 s to-202 (n.isol) s0402mh t106m1 s to-202 (n.isol) s0405bh s2006l d to-220 (isol) s0405dh s4006l d to-220 (isol) s0405mh s6006l s to-220 (isol) s0406bh s2006l s to-220 (isol) s0406dh s4006l s to-220 (isol) s0406mh s6006l s to-220 (isol) s0406nh s8006l s to-220 (isol) s0407bh s2006l s to-220 (isol) s0407dh s4006l s to-220 (isol) s0407mh s6006l s to-220 (isol) s0410bh s2006l s to-220 (isol) s0410dh s4006l s to-220 (isol) s0410mh s6006l s to-220 (isol) s0410nh s8006l s to-220 (isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-17 http://www.teccor.com thyristor product catalog +1 972-580-7777 s0417bh s2006l s to-220 (isol) s0417dh s4006l s to-220 (isol) s0417mh s6006l s to-220 (isol) s0417nh s8006l s to-220 (isol) s0602bh s2006ls2 s to-220 (isol) s0602dh s4006ls2 s to-220 (isol) s0602mh s6006ls2 s to-220 (isol) s0605bh s2006l s to-220 (isol) s0605dh s4006l s to-220 (isol) s0605mh s6006l s to-220 (isol) s0606bh s2006l s to-220 (isol) s0606dh s4006l s to-220 (isol) s0606mh s6006l s to-220 (isol) s0606nh s8006l s to-220 (isol) s0607bh s2006l s to-220 (isol) s0607dh s4006l s to-220 (isol) s0607mh s6006l s to-220 (isol) s0610bh s2006l s to-220 (isol) s0610dh s4006l s to-220 (isol) s0610mh s6006l s to-220 (isol) s0610nh s8006l s to-220 (isol) s0617bh s2006l s to-220 (isol) s0617dh s4006l s to-220 (isol) s0617mh s6006l s to-220 (isol) s0617nh s8006l s to-220 (isol) s0802bh s2008ls2 s to-220 (isol) s0802dh s4008ls2 s to-220 (isol) s0802mh s6008ls2 s to-220 (isol) s0805bh s2006r s to-220 (n.isol) s0805dh s4006r s to-220 (n.isol) s0805mh s6008r s to-220 (n.isol) s0806bh s2008r s to-220 (n.isol) s0806dh s4008r s to-220 (n.isol) s0806mh s6008r s to-220 (n.isol) s0806nh s8008r s to-220 (n.isol) s0807bh s2008r s to-220 (n.isol) s0807dh s4008r s to-220 (n.isol) s0807mh s6008r s to-220 (n.isol) s0807nh s8008r s to-220 (n.isol) s0810bh s2008r s to-220 (n.isol) s0810dh s4008r s to-220 (n.isol) s0810mh s6008r s to-220 (n.isol) s0810nh s8008r s to-220 (n.isol) s0817bh s2008r s to-220 (n.isol) s0817dh s4008r s to-220 (n.isol) s0817mh s6008r s to-220 (n.isol) s0817nh s8008r s to-220 (n.isol) s1005bh s2010r s to-220 (n.isol) s1005dh s4010r s to-220 (n.isol) s1005mh s6010r s to-220 (n.isol) s1006bh s2010r s to-220 (n.isol) s1006dh s4010r s to-220 (n.isol) s1006mh s6010r s to-220 (n.isol) s1006nh s8010r s to-220 (n.isol) s1007bh s2010r s to-220 (n.isol) s1007dh s4010r s to-220 (n.isol) s1007mh s6010r s to-220 (n.isol) s1010bh s2010r s to-220 (n.isol) s1010dh s4010r s to-220 (n.isol) s1010mh s6010r s to-220 (n.isol) s1010nh s8010r s to-220 (n.isol) s1017bh s2010r s to-220 (n.isol) s1017dh s4010r s to-220 (n.isol) s1017mh s6010r s to-220 (n.isol) s1017nh s8010r s to-220 (n.isol) s106a1 t106b1 d to-202 (n.isol) s106b1 t106b1 d to-202 (n.isol) s106c1 t106d1 d to-202 (n.isol) s106d1 t106d1 d to-202 (n.isol) s106e1 t106m1 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package s106f1 t106b1 d to-202 (n.isol) s106m1 t106m1 d to-202 (n.isol) s106y1 t106b1 d to-202 (n.isol) s107a1 t107b1 d to-202 (n.isol) s107b1 t107b1 d to-202 (n.isol) s107c1 t107d1 d to-202 (n.isol) s107d1 t107d1 d to-202 (n.isol) s107e1 t107m1 d to-202 (n.isol) s107f1 t107b1 d to-202 (n.isol) s107m1 t107m1 d to-202 (n.isol) s107q1 t107b1 d to-202 (n.isol) s107y1 t107b1 d to-202 (n.isol) s1205bh s2012r s to-220 (n.isol) s1205dh s4012r s to-220 (n.isol) s1205mh s6012r s to-220 (n.isol) s1206bh s2012r s to-220 (n.isol) s1206dh s4012r s to-220 (n.isol) s1206mh s6012r s to-220 (n.isol) s1206nh s8012r s to-220 (n.isol) s1207bh s2012r s to-220 (n.isol) s1207dh s4012r s to-220 (n.isol) s1207mh s6012r s to-220 (n.isol) s1210bh s2012r s to-220 (n.isol) s1210dh s4012r s to-220 (n.isol) s1210mh s6012r s to-220 (n.isol) s1210nh s8012r s to-220 (n.isol) s1217bh s2012r s to-220 (n.isol) s1217dh s4012r s to-220 (n.isol) s1217mh s6012r s to-220 (n.isol) s1217nh s8012r s to-220 (n.isol) s1610bh s2016r s to-220 (n.isol) s1610dh s4016r s to-220 (n.isol) s1610mh s6016r s to-220 (n.isol) s1610nh s8016r s to-220 (n.isol) s1612bh s2016r s to-220 (n.isol) s1612dh s4016r s to-220 (n.isol) s1612mh s6016r s to-220 (n.isol) s1612nh s8016r s to-220 (n.isol) s1616bh s2016r s to-220 (n.isol) s1616dh s4016r s to-220 (n.isol) s1616mh s6016r s to-220 (n.isol) s1616nh s8016r s to-220 (n.isol) s1a ec103b d to-92 (isol) s1b ec103b d to-92 (isol) s1d ec103d d to-92 (isol) s1m ec103m d to-92 (isol) s1y ec103b s to-92 (isol) s1yy ec103b d to-92 (isol) s2060a s2006ls2 s to-220 (isol) s2060b s2006ls2 s to-220 (isol) s2060c s4006ls2 s to-220 (isol) s2060d s4006ls2 s to-220 (isol) s2060e s6006ls2 s to-220 (isol) s2060f s2006ls2 s to-220 (isol) s2060m s6006ls2 s to-220 (isol) s2060y s2006ls2 s to-220 (isol) s2061a s2006ls3 s to-220 (isol) s2061b s2006ls3 s to-220 (isol) s2061c s4006ls3 s to-220 (isol) s2061d s4006ls3 s to-220 (isol) s2061e s6006ls3 s to-220 (isol) s2061f s2006ls3 s to-220 (isol) s2061q s2006ls3 s to-220 (isol) s2061y s2006ls3 s to-220 (isol) s2062a s2006ls3 s to-220 (isol) s2062b s2006ls3 s to-220 (isol) s2062c s4006ls3 s to-220 (isol) s2062d s4006ls3 s to-220 (isol) s2062e s6006ls3 s to-220 (isol) s2062f s2006ls3 s to-220 (isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-18 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog s2062m s6006ls3 s to-220 (isol) s2062q s2006ls3 s to-220 (isol) s2062y s2006ls3 s to-220 (isol) s2512bh s2025r s to-220 (n.isol) s2512bk s2035j s to-218 (isol) s2512dh s4025r s to-220 (n.isol) s2512dk s4035j s to-218 (isol) s2512mh s6025r s to-220 (n.isol) s2512mk s6035j s to-218 (isol) s2512nh s8025r s to-220 (n.isol) s2512nk s8035j s to-218 (isol) s2514bh s2025r s to-220 (n.isol) s2514bk s2035j s to-218 (isol) s2514dh s4025r s to-220 (n.isol) s2514dk s4035j s to-218 (isol) s2514mh s6025r s to-220 (n.isol) s2514mk s6035j s to-218 (isol) s2514nh s8025r s to-220 (n.isol) s2514nk s8035j s to-218 (isol) s2516bh s2025r s to-220 (n.isol) s2516dh s4025r s to-220 (n.isol) s2516mh s6025r s to-220 (n.isol) s2516nh s8025r s to-220 (n.isol) s2600b s2006l s to-220 (isol) s2600d s4006l s to-220 (isol) s2600m s6006l s to-220 (isol) s2800a s2010r d to-220 (n.isol) s2800b s2010r d to-220 (n.isol) s2800c s4010r s to-220 (n.isol) s2800d s4010r d to-220 (n.isol) s2800e s6010r s to-220 (n.isol) s2800f s2010r d to-220 (n.isol) s2800m s6010r d to-220 (n.isol) s2800n s8010r d to-220 (n.isol) s3014nh s8040r s to-220 (n.isol) s3016nh s8040r s to-220 (n.isol) s4012bh s2040r s to-220 (n.isol) s4012bk s2035j s to-218 (isol) s4012dh s4040r s to-220 (n.isol) s4012dk s4035j s to-218 (isol) s4012mh s6040r s to-220 (n.isol) s4012mk s6035j s to-218 (isol) s4012nh s8040r s to-220 (n.isol) s4012nk s8035j s to-218 (isol) s4014bh s2040r s to-220 (n.isol) s4014bk s2035j s to-218 (isol) s4014dh s4040r s to-220 (n.isol) s4014dk s4035j s to-218 (isol) s4014mh s6040r s to-220 (n.isol) s4014mk s6035j s to-218 (isol) s4014nh s8040r s to-220 (n.isol) s4014nk s8065j s to-218 (isol) s4016bh s2040r s to-220 (n.isol) s4016dh s4040r s to-220 (n.isol) s4016mh s6040r s to-220 (n.isol) s4016nh s8040r s to-220 (n.isol) s4060a s2010ls2 s to-220 (isol) s4060b s2010ls2 s to-220 (isol) s4060c s4010ls2 s to-220 (isol) s4060d s4010ls2 s to-220 (isol) s4060f s2010ls2 s to-220 (isol) s4060u s2010ls2 s to-220 (isol) s5800b s2008r s to-220 (n.isol) s5800c s4008r s to-220 (n.isol) s5800d s4008r s to-220 (n.isol) s5800e s6008r s to-220 (n.isol) s5800m s6008r s to-220 (n.isol) sc129b q2025r5 d to-220 (n.isol) sc129d q4025r5 d to-220 (n.isol) sc129e q6025r5 d to-220 (n.isol) part number teccor device direct or suggested replacement teccor package sc129m q6025r5 d to-220 (n.isol) sc136a q2004f41 s to-202 (n.isol) sc136b q2004f41 s to-202 (n.isol) sc136c q4004f41 s to-202 (n.isol) sc136d q4004f41 s to-202 (n.isol) sc136e q5004f41 s to-202 (n.isol) sc136m q6004f41 s to-202 (n.isol) sc140b q2006l4 d to-220 (isol) sc140d q4006l4 d to-220 (isol) sc140e q6006l4 d to-220 (isol) sc140m q6006l5 d to-220 (isol) sc141a q2006r4 s to-220 (n.isol) sc141b q2006r4 d to-220 (n.isol) sc141c q4006r4 s to-220 (n.isol) sc141d q4006r4 d to-220 (n.isol) sc141e q6006r4 d to-220 (n.isol) sc141m q6006r5 d to-220 (n.isol) sc141n q8006r5 d to-220 (n.isol) sc142b q2008l4 d to-220 (isol) sc142d q4008l4 d to-220 (isol) sc142e q6008l4 d to-220 (isol) sc142m q6008l5 d to-220 (isol) sc143b q2008r4 d to-220 (n.isol) sc143d q4008r4 d to-220 (n.isol) sc143e q6008r4 d to-220 (n.isol) sc143m q6008r5 d to-220 (n.isol) sc146b q2010r5 d to-220 (n.isol) sc146d q4010r5 d to-220 (n.isol) sc146e q6010r5 d to-220 (n.isol) sc146m q6010r5 d to-220 (n.isol) sc146n q8010r5 d to-220 (n.isol) sc147b q2010l5 d to-220 (isol) sc147d q4010l5 d to-220 (isol) sc147e q6010l5 d to-220 (isol) sc147m q6010l5 d to-220 (isol) sc148b q2010l5 d to-220 (isol) sc148d q4010l5 d to-220 (isol) sc148e q6010l5 d to-220 (isol) sc148m q6010l5 d to-220 (isol) sc149b q2015r5 d to-220 (n.isol) sc149d q4015r5 d to-220 (n.isol) sc149e q6015r5 d to-220 (n.isol) sc149m q6015r5 d to-220 (n.isol) sc150b q2015l5 d to-220 (isol) sc150d q4015l5 d to-220 (isol) sc150e q6015l5 d to-220 (isol) sc150m q6015l5 d to-220 (isol) sc151b q2015r5 d to-220 (n.isol) sc151d q4015r5 d to-220 (n.isol) sc151e q6015r5 d to-220 (n.isol) sc151m q6015r5 d to-220 (n.isol) sc160b q6025p5 s fastpak (isol) sc160d q6025p5 s fastpak (isol) sc160e q6025p5 s fastpak (isol) sc160m q6025p5 s fastpak (isol) sc92a q201e3 d to-92 (isol) sc92b q201e3 d to-92 (isol) sc92d q401e3 d to-92 (isol) sc92f q201e3 d to-92 (isol) sf0r1a42 ec103b s to-92 (isol) sf0r1b42 ec103b s to-92 (isol) sf0r1d42 ec103b s to-92 (isol) sf0r1g42 ec103d s to-92 (isol) sf0r3b42 ec103b s to-92 (isol) sf0r3d42 ec103b s to-92 (isol) sf0r3g42 ec103d s to-92 (isol) sf0r3j42 ec103m s to-92 (isol) sf0r5b43 ec103b s to-92 (isol) sf0r5d43 ec103b s to-92 (isol) sf0r5g43 ec103d s to-92 (isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-19 http://www.teccor.com thyristor product catalog +1 972-580-7777 sf0r5h43 ec103m s to-92 (isol) sf0r5j43 ec103m s to-92 (isol) sf10d41a s2016r s to-220 (n.isol) sf10g41a s4016r s to-220 (n.isol) sf10j41a s6016r s to-220 (n.isol) sf1b12 tr22-4 s to-39/to-92 (isol) sf1d12 tr22-4 s to-39/to-92 (isol) sf1g12 tr22-6 s to-39/to-92 (isol) sf3b41 s2006f1 s to-202 (n.isol) sf3b42 t106b1 s to-202 (n.isol) sf3d41 s2006f1 s to-202 (n.isol) sf3d42 t106b1 s to-202 (n.isol) sf3d42c t106b1 s to-202 (n.isol) sf3g41 s4006f1 s to-202 (n.isol) sf3g42 t106d1 s to-202 (n.isol) sf3g42c t106d1 s to-202 (n.isol) sf3h42lc2 t106m2 s to-202 (n.isol) sf3j41 s6006f1 s to-202 (n.isol) sf3j42 t106m1 s to-202 (n.isol) sf5b41 s2008r s to-202 (n.isol) sf5b42 s2008fs21 s to-202 (n.isol) sf5d41 s2008r s to-202 (n.isol) sf5d41a s2012r s to-202 (n.isol) sf5d42 s2008fs21 s to-202 (n.isol) sf5g41 s4008r s to-202 (n.isol) sf5g41a s6012r s to-202 (n.isol) sf5g42 s4008fs21 s to-202 (n.isol) sf5j41 s6008r s to-202 (n.isol) sf5j41a s6012r s to-202 (n.isol) sf5j42 s6008fs21 s to-202 (n.isol) sf8b41 s2012r s to-220 (n.isol) sf8d41 s2012r s to-220 (n.isol) sf8d41a s2012r s to-220 (n.isol) sf8g41 s4012r s to-220 (n.isol) sf8g41a s4012r s to-220 (n.isol) sf8j41 s6012r s to-220 (n.isol) sf8j41a s6012r s to-220 (n.isol) sm0r5b42 q2x8e3 s to-92 (isol) sm0r5d42 q2x8e3 s to-92 (isol) sm0r5g42 q4x8e3 s to-92 (isol) sm12d41 q2012rh5 s to-220 (n.isol) sm12g41 q4012rh5 s to-220 (n.isol) sm12j41 q6012rh5 s to-220 (n.isol) sm16dz41 q2025p5 s fastpak (isol) sm16g45 q4016rh4 s to-220 (n.isol) sm16g45a q4016rh3 s to-220 (n.isol) sm16gz41 q4025p5 s fastpak (isol) sm16gz47 q4016lh4 s to-220 (isol) sm16gz47a q4016lh3 s to-220 (isol) sm16j45 q6016rh4 s to-220 (n.isol) sm16j45a q6016rh3 s to-220 (n.isol) sm16jz41 q6025p5 s fastpak (isol) sm16jz47 q6016lh4 s to-220 (isol) sm16jz47a q6016lh3 s to-220 (isol) sm1d43 l201e6 s to-92 (isol) sm1g43 l401e6 s to-92 (isol) sm25dz41 q2025p5 s fastpak (isol) sm25gz41 q4025p5 s fastpak (isol) sm25jz41 q6025p5 s fastpak (isol) sm2b41 q2004f31 s to-202 (n.isol) sm2d41 q2004f31 s to-202 (n.isol) sm2g41 q4004f31 s to-202 (n.isol) sm3b41 q2004f41 s to-202 (n.isol) sm3d41 q2004f41 s to-202 (n.isol) sm3g41 q4004f41 s to-202 (n.isol) sm3g45 q4004l3 d to-220 (isol) sm3gz46 q4004l3 s to-220 (isol) sm3j41 q6004f41 s to-202 (n.isol) sm3j45 q6004l3 d to-220 (isol) sm3jz46 q6004l3 s to-220 (isol) part number teccor device direct or suggested replacement teccor package sm6d45 q2006r4 s to-220 (n.isol) sm6d45a q2006r4 s to-220 (n.isol) sm6dz46 q2006l4 s to-220 (isol) sm6dz46a q2006l4 s to-220 (isol) sm6g45 q4006r4 s to-220 (n.isol) sm6g45a q4006r4 s to-220 (n.isol) sm6gz46 q4006l4 s to-220 (isol) sm6gz46a q4006l4 s to-220 (isol) sm6gz47 q4006l4 s to-220 (isol) sm6gz47a q4006l4 s to-220 (isol) sm6j45 q6006r4 s to-220 (n.isol) sm6j45a q6006r4 s to-220 (n.isol) sm6jz46 q6006l4 s to-220 (isol) sm6jz46a q6006l4 s to-220 (isol) sm6jz47 q6006l4 s to-220 (isol) sm6jz47a q6006l4 s to-220 (isol) sm8d41 q2008r4 d to-220 (n.isol) sm8d45 q2010r4 s to-220 (n.isol) sm8d45a l2008l8 s to-220 (n.isol) sm8dz46 q2010l4 s to-220 (isol) sm8dz46a l2008l8 s to-220 (isol) sm8g41 q4008r4 d to-220 (n.isol) sm8g45 q4010r4 s to-220 (n.isol) sm8g45a l4008l8 s to-220 (n.isol) sm8gz46 q4010l4 s to-220 (isol) sm8gz46a l4008l8 s to-220 (isol) sm8gz47 q4008lh4 s to-220 (isol) sm8gz47a q4008lh4 s to-220 (isol) sm8j41 q6008r5 d to-220 (n.isol) sm8j45 q6010r4 s to-220 (n.isol) sm8j45a l6008l8 s to-220 (n.isol) sm8jz46 q6010l4 s to-220 (isol) sm8jz46a l6008l8 s to-220 (isol) sm8jz47 q6008lh4 s to-220 (isol) sm8jz47a q6008lh4 s to-220 (isol) st2 ht32 d do-35 (isol) t0505mh l6006l5 s to-220 (isol) t0509mh l6006l6 s to-220 (isol) t0510dh l4006l8 s to-220 (isol) t0510mh l6006l8 s to-220 (isol) t0605dh l4006l5 s to-220 (isol) t0605mh l6006l5 s to-220 (isol) t0609dh l4006l6 s to-220 (isol) t0609mh l6006l6 s to-220 (isol) t0612bh q2004r4 d to-220 (n.isol) t0612dh q4006r4 d to-220 (n.isol) t0612mh q6006r5 d to-220 (n.isol) t0805dh l4008l6 s to-220 (isol) t0805mh l6008l6 s to-220 (isol) t0809dh l4008l8 s to-220 (isol) t0809mh l6008l8 s to-220 (isol) t0810dh q4008r4 s to-220 (n.isol) t0810mh q6008r5 s to-220 (n.isol) t0810nh q8008r5 s to-220 (n.isol) t0810sh q8008r5 s to-220 (n.isol) t0812dh q4008r4 s to-220 (n.isol) t0812mh q6008r5 s to-220 (n.isol) t0812nh q8008r5 s to-220 (n.isol) t0812sh q8008r5 s to-220 (n.isol) t1010bh q2010r5 s to-220 (n.isol) t1010bj q2010l5 d to-220 (isol) t1010dh q4010r5 s to-220 (n.isol) t1010dj q4010l5 d to-220 (isol) t1010mh q6010r5 s to-220 (n.isol) t1010mj q6010l5 d to-220 (isol) t1010nh q8010r5 s to-220 (n.isol) t1010nj q8010l5 d to-220 (isol) t1012bh q2010r5 d to-220 (n.isol) t1012bj q2010l5 d to-220 (isol) t1012dh q4010r5 d to-220 (n.isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-20 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog t1012dj q4010l5 d to-220 (isol) t1012mh q6010r5 d to-220 (n.isol) t1012mj q6010l5 d to-220 (isol) t1012nh q8010r5 s to-220 (n.isol) t1012nj q8010l5 s to-220 (isol) t1013bh q2010r5 d to-220 (n.isol) t1013bj q2010l5 d to-220 (isol) t1013dh q4010r5 d to-220 (n.isol) t1013dj q4010l5 d to-220 (isol) t1013mh q6010r5 d to-220 (n.isol) t1013mj q6010l5 d to-220 (isol) t1013nh q8010r5 d to-220 (n.isol) t1013nj q8010l5 d to-220 (isol) t106a1sc l2004f31 d to-202 (n.isol) t106a1sd l2004f51 d to-202 (n.isol) t106a1sg l2004f61 d to-202 (n.isol) t106a1sh l2004f81 d to-202 (n.isol) t106a1sha q2004f41 d to-202 (n.isol) t106a1ss l2004f31 d to-202 (n.isol) t106a2ss l2004f32 d to-202 (n.isol) t106b1sc l2004f31 d to-202 (n.isol) t106b1sd l2004f51 d to-202 (n.isol) t106b1sg l2004f61 d to-202 (n.isol) t106b1sga q2004f31 d to-202 (n.isol) t106b1sh l2004f81 d to-202 (n.isol) t106b1sha q2004f41 d to-202 (n.isol) t106b1ss l2004f31 d to-202 (n.isol) t106b2sd l2004f52 d to-202 (n.isol) t106b2sg l2004f62 d to-202 (n.isol) t106b2sga q2004f32 d to-202 (n.isol) t106b2sh l2004f82 d to-202 (n.isol) t106b2sha q2004f42 d to-202 (n.isol) t106b2ss l2004f32 d to-202 (n.isol) t106c1sc l4004f31 d to-202 (n.isol) t106c1sd l4004f51 d to-202 (n.isol) t106c1sg l4004f61 d to-202 (n.isol) t106c1sga q4004f31 d to-202 (n.isol) t106c1sh l4004f81 d to-202 (n.isol) t106c1sha q4004f41 d to-202 (n.isol) t106c1ss l4004f31 d to-202 (n.isol) t106c2sd l4004f52 d to-202 (n.isol) t106c2sg l4004f62 d to-202 (n.isol) t106c2sga q4004f32 d to-202 (n.isol) t106c2sh l4004f82 d to-202 (n.isol) t106c2sha q4004f42 d to-202 (n.isol) t106c2ss l4004f32 d to-202 (n.isol) t106d1sc l4004f31 d to-202 (n.isol) t106d1sd l4004f51 d to-202 (n.isol) t106d1sg l4004f61 d to-202 (n.isol) t106d1sga q4004f31 d to-202 (n.isol) t106d1sh l4004f81 d to-202 (n.isol) t106d1sha q4004f41 d to-202 (n.isol) t106d1ss l4004f31 d to-202 (n.isol) t106d2sd l4004f52 d to-202 (n.isol) t106d2sg l4004f62 d to-202 (n.isol) t106d2sga q4004f32 d to-202 (n.isol) t106d2sh l4004f82 d to-202 (n.isol) t106d2sha q4004f42 d to-202 (n.isol) t106d2ss l4004f32 d to-202 (n.isol) t106e1sc l6004f31 d to-202 (n.isol) t106e1sd l6004f51 d to-202 (n.isol) t106e1sg l6004f61 d to-202 (n.isol) t106e1sga q6004f31 d to-202 (n.isol) t106e1sh l6004f81 d to-202 (n.isol) t106e1sha q6004f41 d to-202 (n.isol) t106e1ss l6004f31 d to-202 (n.isol) t106e2sd l6004f52 d to-202 (n.isol) t106e2sg l6004f62 d to-202 (n.isol) t106e2sga q6004f32 d to-202 (n.isol) t106e2sh l6004f82 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package t106e2sha q6004f42 d to-202 (n.isol) t106e2ss l4004f32 d to-202 (n.isol) t106f1sc l2004f31 d to-202 (n.isol) t106f1sd l2004f51 d to-202 (n.isol) t106f1sg l2004f61 d to-202 (n.isol) t106f1sga q2004f31 d to-202 (n.isol) t106f1sh l2004f81 d to-202 (n.isol) t106f1sha q2004f41 d to-202 (n.isol) t106f1ss l2004f31 d to-202 (n.isol) t106f2sc l2004f32 d to-202 (n.isol) t106f2sd l2004f52 d to-202 (n.isol) t106f2sg l2004f62 d to-202 (n.isol) t106f2sga q2004f32 d to-202 (n.isol) t106f2sh l2004f82 d to-202 (n.isol) t106f2sha q2004f42 d to-202 (n.isol) t106f2ss l2004f32 d to-202 (n.isol) t106m1sd l6004f51 d to-202 (n.isol) t106m1sg l6004f61 d to-202 (n.isol) t106m1sga q6004f31 d to-202 (n.isol) t106m1sh l6004f81 d to-202 (n.isol) t106m1sha q6004f41 d to-202 (n.isol) t106m1ss l6004f31 d to-202 (n.isol) t106m2sd l6004f52 d to-202 (n.isol) t106m2sg l6004f62 d to-202 (n.isol) t106m2sga q6004f32 d to-202 (n.isol) t106m2sh l6004f82 d to-202 (n.isol) t106m2sha q6004f42 d to-202 (n.isol) t106m2ss l6004f32 d to-202 (n.isol) t1210bh q2015r5 s to-220 (n.isol) t1210dh q4015r5 s to-220 (n.isol) t1210mh q6015r5 s to-220 (n.isol) t1210nh q8015r5 s to-220 (n.isol) t1212bh q2015r5 d to-220 (n.isol) t1212bj q4015l5 d to-220 (isol) t1212dh q4015r5 d to-220 (n.isol) t1212dj q4015l5 d to-220 (isol) t1212mh q6015r5 d to-220 (n.isol) t1212mj q6015l5 d to-220 (isol) t1212nh q8015r5 d to-220 (n.isol) t1212nj q8015l5 d to-220 (isol) t1213bh q2015r5 d to-220 (n.isol) t1213bj q4015l5 d to-220 (isol) t1213dh q4015r5 d to-220 (n.isol) t1213dj q4015l5 d to-220 (isol) t1213mh q6015r5 d to-220 (n.isol) t1213mj q6015l5 d to-220 (isol) t1213nh q8015r5 d to-220 (n.isol) t1213nj q8015l5 d to-220 (isol) t1235-600g q6012nh5 s to-263 (smt) t1235-800g q8012nh5 s to-263 (smt) t1512bj q2015l5 d to-220 (isol) t1512dj q4015l5 d to-220 (isol) t1512mj q6015l5 d to-220 (isol) t1512nj q8015l5 d to-220 (isol) t1513bj q2015l5 d to-220 (isol) t1513dj q4015l5 d to-220 (isol) t1513mj q6015l5 d to-220 (isol) t1513nj q8015l5 d to-220 (isol) t1612bh q2015r5 d to-220 (n.isol) t1612dh q4015r5 d to-220 (n.isol) t1612mh q6015r5 d to-220 (n.isol) t1612nh q8015r5 d to-220 (n.isol) t1612nj q8015l5 d to-220 (isol) t1613bh q2015r5 d to-220 (n.isol) t1613dh q4015r5 d to-220 (n.isol) t1613mh q6015r5 d to-220 (n.isol) t1613nh q8015r s to-220 (n.isol) t1635-600g q6016nh4 d to-263 (smt) t1635-800g q8016nh4 d to-263 (smt) t2300a l2004f321 s to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-21 http://www.teccor.com thyristor product catalog +1 972-580-7777 t2300b l2004f321 s to-202 (n.isol) t2300d l4004f321 s to-202 (n.isol) t2300f l2004f321 s to-202 (n.isol) t2300pa l2004f31 s to-202 (n.isol) t2300pb l2004f31 s to-202 (n.isol) t2300pc l4004f31 s to-202 (n.isol) t2300pd l4004f31 s to-202 (n.isol) t2300pe l6004f31 s to-202 (n.isol) t2300pf l2004f31 s to-202 (n.isol) t2300pm l6004f31 s to-202 (n.isol) t2301a l2004f321 s to-202 (n.isol) t2301b l2004f321 s to-202 (n.isol) t2301d l4004f321 s to-202 (n.isol) t2301f l2004f321 s to-202 (n.isol) t2301pa l2004f31 s to-202 (n.isol) t2301pb l2004f31 s to-202 (n.isol) t2301pc l4004f31 s to-202 (n.isol) t2301pd l4004f31 s to-202 (n.isol) t2301pe l6004f31 s to-202 (n.isol) t2301pf l2004f31 s to-202 (n.isol) t2301pm l6004f31 s to-202 (n.isol) t2302a l2004f621 s to-202 (n.isol) t2302b l2004f621 s to-202 (n.isol) t2302d l4004f621 s to-202 (n.isol) t2302f l2004f621 s to-202 (n.isol) t2302pa l2004f61 s to-202 (n.isol) t2302pb l2004f61 s to-202 (n.isol) t2302pc l4004f61 s to-202 (n.isol) t2302pd l4004f61 s to-202 (n.isol) t2302pe l6004f61 s to-202 (n.isol) t2302pf l2004f61 s to-202 (n.isol) t2302pm l6004f61 s to-202 (n.isol) t2303f q2004f421 s to-202 (n.isol) t2306a q2004f421 s to-202 (n.isol) t2306b q2004f421 s to-202 (n.isol) t2306d q4004f421 s to-202 (n.isol) t2310a l2004f321 s to-202 (n.isol) t2310b l2004f321 s to-202 (n.isol) t2310d l4004f321 s to-202 (n.isol) t2310f l2004f321 s to-202 (n.isol) t2311a l2004f321 s to-202 (n.isol) t2311b l2004f321 s to-202 (n.isol) t2311d l4004f321 s to-202 (n.isol) t2311f l2004f321 s to-202 (n.isol) t2312a l2004f621 s to-202 (n.isol) t2312b l2004f621 s to-202 (n.isol) t2312d l4004f621 s to-202 (n.isol) t2312f l2004f621 s to-202 (n.isol) t2313a q2004f421 s to-202 (n.isol) t2313b q2004f421 s to-202 (n.isol) t2313d q4004f421 s to-202 (n.isol) t2313f q2004f421 s to-202 (n.isol) t2316a q2004f421 s to-202 (n.isol) t2316b q2004f421 s to-202 (n.isol) t2316d q4004f421 s to-202 (n.isol) t2320a l2004f31 d to-202 (n.isol) t2320b l2004f31 d to-202 (n.isol) t2320c l4004f31 d to-202 (n.isol) t2320d l4004f31 d to-202 (n.isol) t2320e l6004f31 d to-202 (n.isol) t2320f l2004f31 d to-202 (n.isol) t2320m l6004f31 d to-202 (n.isol) t2322a l2004f61 d to-202 (n.isol) t2322b l2004f61 d to-202 (n.isol) t2322c l4004f61 d to-202 (n.isol) t2322d l4004f61 d to-202 (n.isol) t2322e l6004f61 d to-202 (n.isol) t2322f l2004f61 d to-202 (n.isol) t2322m l6004f61 d to-202 (n.isol) t2323a l2004f81 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package t2323b l2004f81 d to-202 (n.isol) t2323c l4004f81 d to-202 (n.isol) t2323d l4004f81 d to-202 (n.isol) t2323e l6004f81 d to-202 (n.isol) t2323f l2004f81 d to-202 (n.isol) t2323m l6004f81 d to-202 (n.isol) t2327a l2004f51 d to-202 (n.isol) t2327b l2004f51 d to-202 (n.isol) t2327c l4004f51 d to-202 (n.isol) t2327d l4004f51 d to-202 (n.isol) t2327e l6004f51 d to-202 (n.isol) t2327f l2004f51 d to-202 (n.isol) t2327m l6004f51 d to-202 (n.isol) t2500a q2006r4 d to-220 (n.isol) t2500afp q2006l4 d to-220 (isol) t2500b q2006r4 d to-220 (n.isol) t2500bfp q2006l4 d to-220 (isol) t2500c q4006r4 d to-220 (n.isol) t2500cfp q4006l4 d to-220 (isol) t2500d q4006r4 d to-220 (n.isol) t2500dfp q4006l4 d to-220 (isol) t2500e q6006r4 d to-220 (n.isol) t2500efp q6006l4 d to-220 (isol) t2500m q6006r5 d to-220 (n.isol) t2500mfp q6006l5 d to-220 (isol) t2500n q8006r5 d to-220 (n.isol) t2500nfp q8006l5 d to-220 (isol) t2500s q8006r5 d to-220 (n.isol) t2500sfp q8006l5 d to-220 (isol) t2506b q2006r4 d to-220 (n.isol) t2506d q4006r4 d to-220 (n.isol) t2512bh q2025r5 s to-220 (n.isol) t2512bk q6025p5 s fastpak (isol) t2512dh q4025r5 s to-220 (n.isol) t2512dk q6025p5 s fastpak (isol) t2512mh q6025r5 s to-220 (n.isol) t2512mk q6025p5 s fastpak (isol) t2512nh q8025r5 s to-220 (n.isol) t2512nk q8025p5 s fastpak (isol) t2513bh q2025r5 s to-220 (n.isol) t2513bk q6025p5 s fastpak (isol) t2513dh q4025r5 s to-220 (n.isol) t2513dk q6025p5 s fastpak (isol) t2513mh q6025r5 s to-220 (n.isol) t2513mk q6025p5 s fastpak (isol) t2513nh q8025r5 s to-220 (n.isol) t2513nk q8025p5 s fastpak (isol) t2535-600g q6025nh6 s to-263 (smt) t2535-800g q8025nh6 s to-263 (smt) t2700b q2006r4 s to-220 (n.isol) t2700d q4006r4 s to-220 (n.isol) t2800a q2008r4 s to-220 (n.isol) t2800b q2008r4 s to-220 (n.isol) t2800c q4008r4 s to-220 (n.isol) t2800d q4008r4 s to-220 (n.isol) t2800e q6008r4 s to-220 (n.isol) t2800m q6008r5 s to-220 (n.isol) t2801a q2006r4 d to-220 (n.isol) t2801b q2006r4 d to-220 (n.isol) t2801c q4006r4 d to-220 (n.isol) t2801d q4006r4 d to-220 (n.isol) t2801e q6006r4 d to-220 (n.isol) t2801m q6006r5 d to-220 (n.isol) t2801n q8006r5 d to-220 (n.isol) t2801s q8006r5 d to-220 (n.isol) t2802a q2008r4 s to-220 (n.isol) t2802b q2008r4 s to-220 (n.isol) t2802c q4008r4 s to-220 (n.isol) t2802d q4008r4 s to-220 (n.isol) t2802e q6008r4 s to-220 (n.isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-22 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog t2802m q6008r5 s to-220 (n.isol) t2806b q2008r4 d to-220 (n.isol) t2806d q4008r4 d to-220 (n.isol) t2806m q6008r5 s to-220 (n.isol) t2850a q2008l4 d to-220 (isol) t2850b q2008l4 d to-220 (isol) t2850d q4008l4 d to-220 (isol) t2850e q6008l4 d to-220 (isol) t2850f q2008l4 d to-220 (isol) t2856b q2008l4 d to-220 (isol) t2856d q4008l4 d to-220 (isol) t4012dks q6035p5 s fastpak (isol) t4012mks q6035p5 s fastpak (isol) t4012nks q8035p5 s fastpak (isol) t4012sks q8035p5 s fastpak (isol) t4013dks q6035p5 s fastpak (isol) t4013mks q6035p5 s fastpak (isol) t4013nks q8035p5 s fastpak (isol) t4013sks q8035p5 s fastpak (isol) t405-400t l4004l6 s to-220 (isol) t405-400w l4004l6 d to-220 (isol) t405-600b l6004d6 s to-252 (smt) t405-600h l6004v6 s to-251 (n.isol) t405-600t l6004l6 s to-220 (isol) t405-600w l6004l6 d to-220 (isol) t410-400t l4004l8 s to-220 (isol) t410-400w l4004l8 d to-220 (isol) t410-600b l6006dh3 s to-252 (smt) t410-600h l6006vh3 s to-251 (n.isol) t410-600t l6004l8 s to-220 (isol) t410-600w l6004l8 d to-220 (isol) t435-400t q4006rh4 d to-220 (n.isol) t435-400w q4006lh4 d to-220 (isol) t435-600b q6006dh4 s to-252 (smt) t435-600h q6006vh4 s to-251 (n.isol) t435-600t q6006rh4 d to-220 (n.isol) t435-600w q6006lh4 d to-220 (isol) t435-700t q8006rh4 d to-220 (n.isol) t435-700w q8006lh4 d to-220 (isol) t435-800t q8006rh4 d to-220 (n.isol) t435-800w q8006lh4 d to-220 (isol) t6000b q2015r5 d to-220 (n.isol) t6000d q4015r5 d to-220 (n.isol) t6000m q6015r5 d to-220 (n.isol) t6001b q2015r5 d to-220 (n.isol) t6001d q4015r5 d to-220 (n.isol) t6001m q6015r5 d to-220 (n.isol) t6006b q2015r5 s to-220 (n.isol) t6006d q4015r5 s to-220 (n.isol) t6006m q6015r5 s to-220 (n.isol) t620-400w q4006lh4 s to-220 (isol) t620-600w q6006lh4 s to-220 (isol) t620-700w q8006lh4 s to-220 (isol) t630-400w q4006lh4 s to-220 (isol) t630-600w q6006lh4 s to-220 (isol) t630-700w q8006lh4 s to-220 (isol) t810-400b q4008dh3 d to-252 (smt) t810-600b q6008dh3 d to-252 (smt) t820-400w q4008lh4 s to-220 (isol) t820-600w q6008lh4 s to-220 (isol) t820-700w q8008lh4 s to-220 (isol) t830-400w q4008lh4 s to-220 (isol) t830-600w q6008lh4 s to-220 (isol) t830-700w q8008lh4 s to-220 (isol) t835-600b q6008dh4 d to-252 (smt) t835-600g q6008nh4 d to-263 (smt) t850-600g q6010nh5 d to-263 (smt) tic106d t106d1 s to-220 (n.isol) tic106m t106m1 s to-220 (n.isol) tic108d t107d1 s to-220 (n.isol) part number teccor device direct or suggested replacement teccor package tic108m t107m1 s to-220 (n.isol) tic116d s4008r d to-220 (n.isol) tic116m s6008r d to-220 (n.isol) tic116n s8008r d to-220 (n.isol) tic116s s8008r d to-220 (n.isol) tic126d s4012r d to-220 (n.isol) tic126m s6012r d to-220 (n.isol) tic126n s8012r d to-220 (n.isol) tic126s s8012r d to-220 (n.isol) tic201d l4004f61 s to-220 (n.isol) tic201m l6004f61 s to-220 (n.isol) tic206d l4004f61 s to-220 (n.isol) tic206m l6004f61 s to-220 (n.isol) tic216d l4006f61 s to-220 (n.isol) tic216m l6006f61 s to-220 (n.isol) tic225d l4008f61 s to-220 (n.isol) tic225m l6008f61 s to-220 (n.isol) tic226d q4008r4 d to-220 (n.isol) tic226m q6008r5 d to-220 (n.isol) tic226n q8008r5 d to-220 (n.isol) tic226s q8008r5 d to-220 (n.isol) tic236d q4015r5 d to-220 (n.isol) tic236m q6015r5 d to-220 (n.isol) tic236n q8015r5 d to-220 (n.isol) tic236s q8015r5 d to-220 (n.isol) tic246d q4015r5 s to-220 (n.isol) tic246m q6015r5 s to-220 (n.isol) tic246n q8015r5 s to-220 (n.isol) tic246s q8015r5 s to-220 (n.isol) tic256d q4025r5 s to-220 (n.isol) tic256d q4025r5 s to-220 (n.isol) tic256m q6025r5 s to-220 (n.isol) tic256n q8025r5 s to-220 (n.isol) tic256s q7025r5 s to-220 (n.isol) ticp106d tcr22-4 s to-92 ticp106m tcr22-8 s to-92 tl1003 s2006f2 s to-202 (n.isol) ? tl1006 s2006f2 s to-202 (n.isol) tl106-05 t106b2 d to-202 (n.isol) tl106-1 t106b2 d to-202 (n.isol) tl106-2 t106b2 d to-202 (n.isol) tl106-4 t106d2 d to-202 (n.isol) tl106-6 t106m2 d to-202 (n.isol) tl107-05 t107b2 d to-202 (n.isol) tl107-1 t107b2 d to-202 (n.isol) tl107-2 t107b2 d to-202 (n.isol) tl107-4 t107d2 d to-202 (n.isol) tl107-6 t107m2 d to-202 (n.isol) tl2003 s2006f2 s to-202 (n.isol) tl2006 s2006f2 s to-202 (n.isol) tl4003 s4006f2 s to-202 (n.isol) tl4006 s4006f2 s to-202 (n.isol) tl6003 s6006f2 s to-202 (n.isol) tl6006 s6006f2 s to-202 (n.isol) tlc111a l2004f62 d to-202 (n.isol) tlc111b q2004f42 d to-202 (n.isol) tlc111d l2004f52 d to-202 (n.isol) tlc111s l2004f62 d to-202 (n.isol) tlc111t l2004f52 d to-202 (n.isol) tlc113b q2004f42 d to-202 (n.isol) tlc1165 l2004f62 d to-202 (n.isol) tlc116a l2004f62 d to-202 (n.isol) tlc116b q2004f42 d to-202 (n.isol) tlc116d l2004f52 d to-202 (n.isol) tlc116t l2004f52 d to-202 (n.isol) tlc221a l4004f62 d to-202 (n.isol) tlc221b q4004f42 d to-202 (n.isol) tlc221d l4004f52 d to-202 (n.isol) tlc221s l4004f62 d to-202 (n.isol) tlc221t l4004f52 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-23 http://www.teccor.com thyristor product catalog +1 972-580-7777 tlc223a l4004f62 d to-202 (n.isol) tlc223b q4004f42 d to-202 (n.isol) tlc223d l4004f52 d to-202 (n.isol) tlc226a l4004f62 d to-202 (n.isol) tlc226b q4004f42 d to-202 (n.isol) tlc226d l4004f52 d to-202 (n.isol) tlc226s l4004f62 d to-202 (n.isol) tlc226t l4004f52 d to-202 (n.isol) tlc331a l6004f62 d to-202 (n.isol) tlc331b q6004f42 d to-202 (n.isol) tlc331d l6004f52 d to-202 (n.isol) tlc331s l6004f62 d to-202 (n.isol) tlc331t l6004f52 d to-202 (n.isol) tlc333a l6004f62 d to-202 (n.isol) tlc333b q6004f42 d to-202 (n.isol) tlc333d l6004f52 d to-202 (n.isol) tlc336a l6004f62 d to-202 (n.isol) tlc336b q6004f42 d to-202 (n.isol) tlc336d l6004f52 d to-202 (n.isol) tlc336s l6004f62 d to-202 (n.isol) tlc336t l6004f52 d to-202 (n.isol) tlc386b q7004f42 d to-202 (n.isol) tls106-05 t106b2 d to-202 (n.isol) tls106-1 t106b2 d to-202 (n.isol) tls106-2 t106b2 d to-202 (n.isol) tls106-4 t106d2 d to-202 (n.isol) tls106-6 t106m2 d to-202 (n.isol) tls107-05 t107b2 d to-202 (n.isol) tls107-1 t107b2 d to-202 (n.isol) tls107-2 t107b2 d to-202 (n.isol) tls107-4 t107d2 d to-202 (n.isol) tls107-6 t107m2 d to-202 (n.isol) tn1215-600b s6012d s to-252 (smt) tn1215-600h s6012v s to-251 (n.isol) tn1215-800b s8012d s to-252 (smt) tn1215-800h s8012v s to-251 (n.isol) tn1625-1000g sk016n s to-263 (smt) tn1625-600g s6016n s to-263 (smt) tn1625-800g s8016n s to-263 (smt) tn815-600b s6008d d to-252 (smt) tn815-600h s6008v d to-251 (n.isol) tn815-800b s8008d d to-252 (smt) tn815-800h s8008v d to-251 (n.isol) to1013bj q2010l5 d to-220 (isol) to1013dj q4010l5 d to-220 (isol) to1013mj q6010l5 d to-220 (isol) to1013nj q8010l5 d to-220 (isol) to409bj l2004l6 d to-220 (isol) to409dj l4004l6 d to-220 (isol) to409mj l6004l6 d to-220 (isol) to410bj l2004l8 d to-220 (isol) to410dj l4004l8 d to-220 (isol) to410mj l6004l8 d to-220 (isol) to505bh l2006l5 s to-220 (isol) to505dh l4006l5 s to-220 (isol) to509bh l2006l6 s to-220 (isol) to509dh l2006l6 s to-220 (isol) to510bh l2006l8 s to-220 (isol) to512bh q2006r4 d to-220 (n.isol) to512dh q4006r4 d to-220 (n.isol) to512mh q6006r5 s to-220 (n.isol) to605bh l2006l5 s to-220 (isol) to605dh l4006l5 s to-220 (isol) to605mh l6006l5 s to-220 (isol) to609bh l2006l6 s to-220 (isol) to609bj l2006l6 d to-220 (isol) to609dh l4006l6 s to-220 (isol) to609dj l4006l6 d to-220 (isol) to609mh l6006l6 s to-220 (isol) to609mj l6006l6 d to-220 (isol) part number teccor device direct or suggested replacement teccor package to610bh l2006l8 s to-220 (isol) to610bj l2006l8 d to-220 (isol) to610dh l4006l8 s to-220 (isol) to610dj l4006l8 d to-220 (isol) to610mh l6006l8 s to-220 (isol) to610mj l6006l8 d to-220 (isol) to612bj q2006l4 s to-220 (isol) to612dj q4006l4 s to-220 (isol) to612mj q6006l5 s to-220 (isol) to805bh l2008l6 s to-220 (isol) to805dh l4008l6 s to-220 (isol) to805mh l6008l6 s to-220 (isol) to809bh l2008l6 s to-220 (isol) to809dh l4008l6 s to-220 (isol) to809mh l6008l6 s to-220 (isol) to810bh l2008l8 s to-220 (isol) to810bj l2008l8 d to-220 (isol) to810dh l4008l8 s to-220 (isol) to810dj l4008l8 d to-220 (isol) to810mh l6008l8 s to-220 (isol) to810mj l6008l8 d to-220 (isol) to812bh q2008r4 s to-220 (n.isol) to812bj q2008l4 s to-220 (isol) to812dh q4008r4 s to-220 (n.isol) to812dj q4008l4 s to-220 (isol) to812mh q6008r5 s to-220 (n.isol) to812mj q6008l5 s to-220 (isol) to812nh q8008l5 s to-220 (isol) to813bj q2008l4 s to-220 (isol) to813dj q4008l4 s to-220 (isol) to813mj q6008l5 s to-220 (isol) to813nj q8008l5 s to-220 (isol) tpdv125 q2025l6 s to-220 (isol) tpdv140 q2040k7 d to-218 (isol) tpdv225 q2025l6 s to-220 (isol) tpdv240 q2040k7 d to-218 (isol) tpdv425 q4025l6 s to-220 (isol) tpdv-440 q4040j7 d to-218 (isol) tpdv625 q6025l6 s to-220 (isol) tpdv-640 q6040k7 d to-218 (isol) tpdv825 q8025l6 s to-220 (isol) tpdv-840 q8040k7 d to-218 (isol) ts420-400t t106d1 s to-202 (n.isol) ts420-600b s6004ds2 s to-252 (smt) ts420-600h s6004vs2 s to-251 (n.isol) ts420-600t t106m1 s to-202 (n.isol) ts820-400t s4008fs21 s to-202 (n.isol) ts820-600b s6008ds2 s to-252 (smt) ts820-600h s6008vs2 s to-251 (n.isol) ts820-600t s6008fs21 s to-202 (n.isol) txdv-212 q2015l6 d to-220 (isol) txdv-412 q4015l6 d to-220 (isol) txdv612 q6015l6 d to-220 (isol) txdv812 q8015l6 d to-220 (isol) txn0510 s2010l d to-220 (isol) txn0512 s2015l s to-220 (isol) txn056 s2006l d to-220 (isol) txn058 s2008l d to-220 (isol) txn058g s2008l d to-220 (isol) txn106 s2006l d to-220 (isol) txn108 s2008l s to-220 (isol) txn108g s2008l d to-220 (isol) txn110 s2010l d to-220 (isol) txn112 s2015l s to-220 (isol) txn204 s2006l s to-220 (isol) txn206 s2006l d to-220 (isol) txn208 s2008l d to-220 (isol) txn208g s2008l d to-220 (isol) txn210 s2010l d to-220 (isol) txn212 s2015l s to-220 (isol) part number teccor device direct or suggested replacement teccor package
cross reference guide appendix http://www.teccor.com a-24 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog txn404 s4006l s to-220 (isol) txn406 s4006l d to-220 (isol) txn408 s4008l d to-220 (isol) txn408g s4008l d to-220 (isol) txn410 s4010l d to-220 (isol) txn412 s4015l s to-220 (isol) txn604 s6006l s to-220 (isol) txn606 s6006l d to-220 (isol) txn608 s6008l d to-220 (isol) txn608g s6008l d to-220 (isol) txn610 s6010l d to-220 (isol) txn612 s6015l s to-220 (isol) txn812 s8015l s to-220 (isol) tyn0510 s2010r d to-220 (isol) tyn0512 s2012r d to-220 (isol) tyn0516 s2016r d to-220 (isol) tyn054 s2006f1 s to-202 (n.isol) tyn056 s2006f1 s to-202 (n.isol) tyn058 s2008r d to-220 (n.isol) tyn058g s2008r s to-220 (n.isol) tyn058k s2008r s to-220 (n.isol) tyn104 s2006f1 s to-202 (n.isol) tyn106 s2006f1 s to-202 (n.isol) tyn108 s2008r d to-220 (n.isol) tyn108g s2008r s to-220 (n.isol) tyn110 s2010r d to-220 (n.isol) tyn112 s2012r d to-220 (n.isol) tyn116 s2016r d to-220 (n.isol) tyn204 s2006f1 s to-202 (n.isol) tyn206 s2006f1 s to-202 (n.isol) tyn208 s2008r d to-220 (n.isol) tyn208g s2008r s to-220 (n.isol) tyn208k s2008r s to-220 (n.isol) tyn210 s2010r d to-220 (n.isol) tyn212 s2012r d to-220 (n.isol) tyn216 s2016r d to-220 (n.isol) tyn404 s4006f1 s to-202 (n.isol) tyn406 s4006f1 s to-202 (n.isol) tyn408 s4008r d to-220 (n.isol) tyn408g s4008r s to-220 (n.isol) tyn408k s4008r s to-220 (n.isol) tyn410 s4010r d to-220 (n.isol) tyn412 s4012r s to-220 (n.isol) tyn416 s4016r d to-220 (n.isol) tyn604 s6006f1 s to-202 (n.isol) tyn606 s6006f1 s to-202 (n.isol) tyn608 s6008r d to-220 (n.isol) tyn608g s6008r s to-220 (n.isol) tyn608k s6008r s to-220 (n.isol) tyn610 s6010r d to-220 (n.isol) tyn612 s6012r d to-220 (n.isol) tyn616 s6016r d to-220 (n.isol) tyn682 s2025r d to-220 (n.isol) tyn683 s2025r d to-220 (n.isol) tyn685 s2025r d to-220 (n.isol) tyn688 s4025r d to-220 (n.isol) tyn690 s6025r d to-220 (n.isol) tyn808 s8008r d to-220 (n.isol) tyn808g s8008r s to-220 (n.isol) tyn808k s8008r s to-220 (n.isol) tyn810 s8010r s to-220 (n.isol) tyn812 s8012r d to-220 (n.isol) tyn816 s8016r d to-220 (n.isol) tys1006-05 s2010ls2 s to-220 (isol) tys1006-1 s2010ls2 s to-220 (isol) tys1006-2 s2010ls2 s to-220 (isol) tys1006-4 s4010ls2 s to-220 (isol) tys1007-05 s2010ls3 s to-220 (isol) tys1007-1 s2010ls2 s to-220 (isol) tys1007-2 s2010ls2 s to-220 (isol) part number teccor device direct or suggested replacement teccor package tys1007-4 s4010ls2 s to-220 (isol) tys406-05 t106b1 s to-202 (n.isol) tys406-1 t106b1 s to-202 (n.isol) tys406-2 t106b1 s to-202 (n.isol) tys406-4 t106d1 s to-202 (n.isol) tys406-6 t106m1 s to-202 (n.isol) tys407-05 t107b1 s to-202 (n.isol) tys407-1 t107b1 s to-202 (n.isol) tys407-2 t107b1 s to-202 (n.isol) tys407-4 t107d1 s to-202 (n.isol) tys407-6 t107m1 s to-202 (n.isol) tys606-05 s2006ls2 d to-220 (isol) tys606-1 s2006ls2 d to-220 (isol) tys606-2 s2006ls2 d to-220 (isol) tys606-4 s4006ls2 d to-220 (isol) tys606-6 s6006ls2 s to-220 (isol) tys607-05 s2006ls3 d to-220 (isol) tys607-1 s2006ls3 d to-220 (isol) tys607-2 s2006ls3 d to-220 (isol) tys607-4 s4006ls3 d to-220 (isol) tys607-6 s6006ls3 s to-220 (isol) tys806-05 s2008ls2 d to-220 (isol) tys806-1 s2008ls2 d to-220 (isol) tys806-2 s2008ls2 d to-220 (isol) tys806-4 s4008ls2 d to-220 (isol) tys806-6 s6008ls2 s to-220 (isol) tys807-05 s2008ls3 d to-220 (isol) tys807-1 s2008ls3 d to-220 (isol) tys807-2 s2008ls3 d to-220 (isol) tys807-4 s4008ls3 d to-220 (isol) tys807-6 s6008ls3 s to-220 (isol) x0101ba ec103b1 s to-92 (isol) x0101da ec103d1 s to-92 (isol) x0101ma ec103m1 s to-92 (isol) x0102ba ec103b s to-92 (isol) x0102da ec103d s to-92 (isol) x0102ma ec103m s to-92 (isol) x0103ba ec103b s to-92 (isol) x0103da ec103d s to-92 (isol) x0103ma ec103m s to-92 (isol) x0104ba ec103b2 d to-92 (isol) x0104da ec103d2 d to-92 (isol) x0104ma ec103m2 d to-92 (isol) x0105ba ec103b2 s to-92 (isol) x0105da ec103d2 s to-92 (isol) x0105ma ec103m2 s to-92 (isol) x0106ba ec103b s to-92 (isol) x0106da ec103d s to-92 (isol) x0106ma ec103m s to-92 (isol) x0110ba ec103b1 s to-92 (isol) x0110da ec103d1 s to-92 (isol) x0110ma ec103m1 s to-92 (isol) x0202ba tcr22-4 d to-92 (isol) x0202da tcr22-6 d to-92 (isol) x0202ma tcr22-8 d to-92 (isol) x0203ba tcr22-4 s to-92 (isol) x0203da tcr22-6 s to-92 (isol) x0203ma tcr22-8 s to-92 (isol) x0204ba tcr22-4 s to-92 (isol) x0204da tcr22-6 s to-92 (isol) x0204ma tcr22-8 s to-92 (isol) x0205ba ec103b2 s to-92 (isol) x0205da ec103d2 s to-92 (isol) x0205ma ec103m2 s to-92 (isol) x0206ba tcr22-4 s to-92 (isol) x0206da tcr22-6 s to-92 (isol) x0402be t106b1 d to-202 (n.isol) x0402bf t106b2 d to-202 (n.isol) x0402de t106d1 d to-202 (n.isol) x0402df t106d2 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
appendix cross reference guide ?2002 teccor electronics a-25 http://www.teccor.com thyristor product catalog +1 972-580-7777 x0402dg t106d1 s to-202 (n.isol) x0402me t106m1 d to-202 (n.isol) x0402mf t106m2 d to-202 (n.isol) x0403be t106b1 s to-202 (n.isol) x0403bf t106b2 s to-202 (n.isol) x0403de t106d1 s to-202 (n.isol) x0403df t106d2 s to-202 (n.isol) x0403me t106m1 s to-202 (n.isol) x0403mf t106m2 s to-202 (n.isol) x0405be t106b1 s to-202 (n.isol) x0405bf t106b2 s to-202 (n.isol) x0405de t106d1 s to-202 (n.isol) x0405df t106d2 s to-202 (n.isol) x0405me t106m1 s to-202 (n.isol) x0405mf t106m2 s to-202 (n.isol) z00607da l4x8e5 s to-92 (isol) z00607ma l6x8e5 s to-92 (isol) z0102ba l201e3 d to-92 (isol) z0102da l401e3 d to-92 (isol) z0102ma l601e3 d to-92 (isol) z0103dn l4n3 s sot223/compak z0103mn l6n3 s sot223/compak z0105ba l201e5 d to-92 (isol) z0105da l401e5 d to-92 (isol) z0105ma l601e5 d to-92 (isol) z0107dn l4n5 s sot223/compak z0107mn l6n5 s sot223/compak z0109ba l201e6 d to-92 (isol) z0109da l401e6 d to-92 (isol) z0109ma l601e6 d to-92 (isol) z0110da l401e8 d to-92 (isol) z0110ma l601e8 d to-92 (isol) z0302bg l2004f321 s to-202 (n.isol) z0302dg l4004f321 s to-202 (n.isol) z0302mg l6004l3 s to-220 (isol) z0305bg l2004f521 s to-202 (n.isol) z0305dg l4004f521 s to-202 (n.isol) z0309bg l2004f621 s to-202 (n.isol) z0309dg l4004f621 s to-202 (n.isol) z0310bg l2004f821 s to-202 (n.isol) z0310dg l4004f821 s to-202 (n.isol) z0310mg l6004l8 s to-220 (isol) z0405be l2004f51 d to-202 (n.isol) z0405bf l2004f52 d to-202 (n.isol) z0405de l4004f51 d to-202 (n.isol) z0405df l4004f52 d to-202 (n.isol) z0405me l6004f51 d to-202 (n.isol) z0405mf l6004f52 d to-202 (n.isol) z0409be l2004f61 d to-202 (n.isol) z0409bf l2004f62 d to-202 (n.isol) z0409de l4004f61 d to-202 (n.isol) z0409df l4004f62 d to-202 (n.isol) z0409me l6004f61 d to-202 (n.isol) z0409mf l6004f62 d to-202 (n.isol) z0410be l2004f81 d to-202 (n.isol) z0410be l2004f81 d to-202 (n.isol) z0410bf l2004f82 d to-202 (n.isol) z0410bf l2004f82 d to-202 (n.isol) z0410de l4004f81 d to-202 (n.isol) z0410de l4004f81 d to-202 (n.isol) z0410df l4004f82 d to-202 (n.isol) z0410me l6004f81 d to-202 (n.isol) z0410mf l6004f82 d to-202 (n.isol) part number teccor device direct or suggested replacement teccor package
notes
?2002 teccor electronics a-27 http://www.teccor.com thyristor product catalog +1 972-580-7777 part number index
part number index teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. http://www.teccor.com a-28 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog 2n5064 e5-2 2n6565 e5-2 d2015l e7-2 d2020l e7-2 d2025l e7-2 d4015l e7-2 d4020l e7-2 d4025l e7-2 d6015l e7-2 d6020l e7-2 d6025l e7-2 d8015l e7-2 d8020l e7-2 d8025l e7-2 dk015l e7-2 dk020l e7-2 dk025l e7-2 ec103b e5-2 ec103b1 e5-2 ec103b2 e5-2 ec103b3 e5-2 ec103d e5-2 ec103d1 e5-2 ec103d2 e5-2 ec103d3 e5-2 ec103m e5-2 ec103m1 e5-2 ec103m2 e5-2 ec103m3 e5-2 ht-32 e8-2 ht-32a e8-2 ht-32b e8-2 ht-34b e8-2 ht-35 e8-2 ht-36a e8-2 ht-36b e8-2 ht-40 e8-2 ht-5761 e8-2 ht-5761a e8-2 ht-5762 e8-2 k0900e70 e9-2 k0900g e9-2 k0900s e9-2 k1050e70 e9-2 k1050g e9-2 k1050s e9-2 k1100e70 e9-2 k1100g e9-2 k1100s e9-2 k1200e70 e9-2 k1200g e9-2 k1200s e9-2 k1300e70 e9-2 k1300g e9-2 k1300s e9-2 k1400e70 e9-2 k1400g e9-2 k1400s e9-2 k1500e70 e9-2 k1500g e9-2 k1500s e9-2 k2000e70 e9-2 k2000f1 e9-2 k2000g e9-2 k2000s e9-2 k2200e70 e9-2 k2200f1 e9-2 k2200g e9-2 k2200s e9-2 k2400e70 e9-2 k2400f1 e9-2 k2400g e9-2 k2400s e9-2 k2500e70 e9-2 k2500f1 e9-2 k2500g e9-2 k2500s e9-2 k3000f1 e9-2 l2004d3 e1-2 l2004d5 e1-2 l2004d6 e1-2 l2004d8 e1-2 l2004f31 e1-2 l2004f51 e1-2 l2004f61 e1-2 l2004f81 e1-2 l2004l3 e1-2 l2004l5 e1-2 l2004l6 e1-2 l2004l8 e1-2 l2004v3 e1-2 l2004v5 e1-2 l2004v6 e1-2 l2004v8 e1-2 l2006d5 e1-4 l2006d6 e1-4 l2006d8 e1-4 l2006l5 e1-4 l2006l6 e1-4 l2006l8 e1-4 l2006v5 e1-4 l2006v6 e1-4 l2006v8 e1-4 l2008d6 e1-4 l2008d8 e1-4 l2008l6 e1-4 l2008l8 e1-4 l2008v6 e1-4 l2008v8 e1-4 l201e3 e1-2 l201e5 e1-2 l201e6 e1-2 l201e8 e1-2 l2n3 e1-2 l2n5 e1-2 l2x3 e1-2 l2x5 e1-2 l2x8e3 e1-2 l2x8e5 e1-2 l2x8e6 e1-2 l2x8e8 e1-2 l4004d3 e1-2 l4004d5 e1-2 l4004d6 e1-2 l4004d8 e1-2 l4004f31 e1-2 l4004f51 e1-2 l4004f61 e1-2 l4004f81 e1-2 l4004l3 e1-2 l4004l5 e1-2 l4004l6 e1-2 l4004l8 e1-2 l4004v3 e1-2 l4004v5 e1-2 l4004v6 e1-2 l4004v8 e1-2 l4006d5 e1-4 l4006d6 e1-4 l4006d8 e1-4 l4006l5 e1-4 l4006l6 e1-4 l4006l8 e1-4 l4006v5 e1-4 l4006v6 e1-4 l4006v8 e1-4 l4008d6 e1-4 l4008d8 e1-4 l4008l6 e1-4 l4008l8 e1-4 l4008v6 e1-4 l4008v8 e1-4 l401e3 e1-2 l401e5 e1-2 l401e6 e1-2 l401e8 e1-2 l4n3 e1-2 l4n5 e1-2 l4x3 e1-2 l4x5 e1-2 l4x8e3 e1-2 l4x8e5 e1-2 l4x8e6 e1-2 l4x8e8 e1-2 l6004d3 e1-2 l6004d5 e1-2 l6004d6 e1-2 l6004d8 e1-2 l6004f31 e1-2 l6004f51 e1-2 l6004f61 e1-2 l6004f81 e1-2 l6004l3 e1-2 l6004l5 e1-2 l6004l6 e1-2 l6004l8 e1-2 l6004v3 e1-2 l6004v5 e1-2 l6004v6 e1-2 l6004v8 e1-2 l6006d5 e1-4 l6006d6 e1-4 l6006d8 e1-4 l6006l5 e1-4 l6006l6 e1-4 l6006l8 e1-4 l6006v5 e1-4 l6006v6 e1-4 l6006v8 e1-4 l6008d6 e1-4 l6008d8 e1-4 l6008l6 e1-4 l6008l8 e1-4 l6008v6 e1-4 l6008v8 e1-4 l601e3 e1-2 l601e5 e1-2 l601e6 e1-2 l601e8 e1-2 l6n3 e1-2 l6n5 e1-2 l6x3 e1-2 l6x5 e1-2 l6x8e3 e1-2 l6x8e5 e1-2 l6x8e6 e1-2 l6x8e8 e1-2 q2004d3 e2-2 q2004d4 e2-2 q2004f31 e2-2 q2004f41 e2-2 q2004l3 e2-2 q2004l4 e2-2 q2004lt e3-2 q2004v3 e2-2 q2004v4 e2-2 q2006dh3 e4-2 q2006dh4 e4-2 q2006f41 e2-2 q2006l4 e2-2 q2006lh4 e4-2 q2006lt e3-2 q2006n4 e2-2 q2006nh4 e4-2 q2006r4 e2-2 q2006rh4 e4-2 q2006vh3 e4-2 q2006vh4 e4-2 q2008dh3 e4-2 q2008dh4 e4-2
part number index ?2002 teccor electronics a-29 http://www.teccor.com thyristor product catalog +1 972-580-7777 teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. q2008f41 e2-2 q2008l4 e2-2 q2008lh4 e4-2 q2008lt e3-2 q2008n4 e2-2 q2008nh4 e4-2 q2008r4 e2-2 q2008rh4 e4-2 q2008vh3 e4-2 q2008vh4 e4-2 q2010f51 e2-4 q2010l4 e2-4 q2010l5 e2-4 q2010lh5 e4-2 q2010lt e3-2 q2010n4 e2-4 q2010n5 e2-4 q2010nh5 e4-2 q2010r4 e2-4 q2010r5 e2-4 q2010rh5 e4-2 q2012lh5 e4-2 q2012nh5 e4-2 q2012rh5 e4-2 q2015l5 e2-4 q2015lt e3-2 q2015n5 e2-4 q2015r5 e2-4 q2016lh3 e4-4 q2016lh4 e4-4 q2016lh6 e4-4 q2016rh3 e4-4 q2016rh4 e4-4 q2016rh6 e4-4 q201e3 e2-2 q201e4 e2-2 q2025j6 e4-4 q2025k6 e4-4 q2025l6 e4-4 q2025n5 e2-4 q2025r5 e2-4 q2025r6 e4-4 q2030lh5 e4-4 q2035nh5 e4-4 q2035rh5 e4-4 q2040j7 e4-4 q2040k7 e4-4 q2n3 e2-2 q2n4 e2-2 q2x3 e2-2 q2x4 e2-2 q2x8e3 e2-2 q2x8e4 e2-2 q4004d3 e2-2 q4004d4 e2-2 q4004f31 e2-2 q4004f41 e2-2 q4004l3 e2-2 q4004l4 e2-2 q4004lt e3-2 q4004v3 e2-2 q4004v4 e2-2 q4006dh3 e4-2 q4006dh4 e4-2 q4006f41 e2-2 q4006l4 e2-2 q4006lh4 e4-2 q4006lt e3-2 q4006lth e3-2 q4006n4 e2-2 q4006nh4 e4-2 q4006r4 e2-2 q4006rh4 e4-2 q4006vh3 e4-2 q4006vh4 e4-2 q4008dh3 e4-2 q4008dh4 e4-2 q4008f41 e2-2 q4008l4 e2-2 q4008lh4 e4-2 q4008lt e3-2 q4008lth e3-2 q4008n4 e2-2 q4008nh4 e4-2 q4008r4 e2-2 q4008rh4 e4-2 q4008vh3 e4-2 q4008vh4 e4-2 q4010f51 e2-4 q4010l4 e2-4 q4010l5 e2-4 q4010lh5 e4-2 q4010lt e3-2 q4010lth e3-2 q4010n4 e2-4 q4010n5 e2-4 q4010nh5 e4-2 q4010r4 e2-4 q4010r5 e2-4 q4010rh5 e4-2 q4012lh5 e4-2 q4012nh5 e4-2 q4012rh5 e4-2 q4015l5 e2-4 q4015lt e3-2 q4015lth e3-2 q4015n5 e2-4 q4015r5 e2-4 q4016lh3 e4-4 q4016lh4 e4-4 q4016lh6 e4-4 q4016rh3 e4-4 q4016rh4 e4-4 q4016rh6 e4-4 q401e3 e2-2 q401e4 e2-2 q4025j6 e4-4 q4025k6 e4-4 q4025l6 e4-4 q4025n5 e2-4 q4025r5 e2-4 q4025r6 e4-4 q4030lh5 e4-4 q4035nh5 e4-4 q4035rh5 e4-4 q4040j7 e4-4 q4040k7 e4-4 q4n3 e2-2 q4n4 e2-2 q4x3 e2-2 q4x4 e2-2 q4x8e3 e2-2 q4x8e4 e2-2 q6004d3 e2-2 q6004d4 e2-2 q6004f31 e2-2 q6004f41 e2-2 q6004l3 e2-2 q6004l4 e2-2 q6004lt e3-2 q6004v3 e2-2 q6004v4 e2-2 q6006dh3 e4-2 q6006dh4 e4-2 q6006f51 e2-2 q6006l5 e2-2 q6006lh4 e4-2 q6006lt e3-2 q6006lth e3-2 q6006n5 e2-2 q6006nh4 e4-2 q6006r5 e2-2 q6006rh4 e4-2 q6006vh3 e4-2 q6006vh4 e4-2 q6008dh3 e4-2 q6008dh4 e4-2 q6008f51 e2-2 q6008l5 e2-2 q6008lh4 e4-2 q6008lt e3-2 q6008lth e3-2 q6008n5 e2-2 q6008nh4 e4-2 q6008r5 e2-2 q6008rh4 e4-2 q6008vh3 e4-2 q6008vh4 e4-2 q6010f51 e2-4 q6010l4 e2-4 q6010l5 e2-4 q6010lh5 e4-2 q6010lt e3-2 q6010lth e3-2 q6010n4 e2-4 q6010n5 e2-4 q6010nh5 e4-2 q6010r4 e2-4 q6010r5 e2-4 q6010rh5 e4-2 q6012lh5 e4-2 q6012nh5 e4-2 q6012rh5 e4-2 q6015l5 e2-4 q6015lt e3-2 q6015lth e3-2 q6015n5 e2-4 q6015r5 e2-4 q6016lh3 e4-4 q6016lh4 e4-4 q6016lh6 e4-4 q6016rh3 e4-4 q6016rh4 e4-4 q6016rh6 e4-4 q601e3 e2-2 q601e4 e2-2 q6025j6 e4-4 q6025k6 e4-4 q6025l6 e4-4 q6025n5 e2-4 q6025p5 e2-4 q6025r5 e2-4 q6025r6 e4-4 q6030lh5 e4-4 q6035nh5 e4-4 q6035p5 e2-4 q6035rh5 e4-4 q6040j7 e4-4 q6040k7 e4-4 q6n3 e2-2 q6n4 e2-2 q6x3 e2-2 q6x4 e2-2 q6x8e3 e2-2 q6x8e4 e2-2 q8004d4 e2-2 q8004l4 e2-2 q8004v4 e2-2 q8006dh3 e4-2 q8006dh4 e4-2 q8006l5 e2-2 q8006lh4 e4-2 q8006n5 e2-2 q8006nh4 e4-2 q8006r5 e2-2 q8006rh4 e4-2 q8006vh3 e4-2 q8006vh4 e4-2 q8008dh3 e4-2 q8008dh4 e4-2
part number index teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. http://www.teccor.com a-30 ?2002 teccor electronics +1 972-580-7777 thyristor product catalog q8008l5 e2-2 q8008lh4 e4-2 q8008n5 e2-2 q8008nh4 e4-2 q8008r5 e2-2 q8008rh4 e4-2 q8008vh3 e4-2 q8008vh4 e4-2 q8010l4 e2-4 q8010l5 e2-4 q8010lh5 e4-2 q8010n4 e2-4 q8010n5 e2-4 q8010nh5 e4-2 q8010r4 e2-4 q8010r5 e2-4 q8010rh5 e4-2 q8012lh5 e4-2 q8012nh5 e4-2 q8012rh5 e4-2 q8015l5 e2-4 q8015n5 e2-4 q8015r5 e2-4 q8016lh3 e4-4 q8016lh4 e4-4 q8016lh6 e4-4 q8016rh3 e4-4 q8016rh4 e4-4 q8016rh6 e4-4 q8025j6 e4-4 q8025k6 e4-4 q8025l6 e4-4 q8025n5 e2-4 q8025p5 e2-4 q8025r5 e2-4 q8025r6 e4-4 q8035p5 e2-4 q8040j7 e4-4 q8040k7 e4-4 qk004d4 e2-2 qk004l4 e2-2 qk004v4 e2-2 qk006dh3 e4-2 qk006dh4 e4-2 qk006l5 e2-2 qk006lh4 e4-2 qk006n5 e2-2 qk006nh4 e4-2 qk006r5 e2-2 qk006rh4 e4-2 qk006vh3 e4-2 qk006vh4 e4-2 qk008dh3 e4-2 qk008dh4 e4-2 qk008l5 e2-2 qk008lh4 e4-2 qk008n5 e2-2 qk008nh4 e4-2 qk008r5 e2-2 qk008rh4 e4-2 qk008vh3 e4-2 qk008vh4 e4-2 qk010l4 e2-4 qk010l5 e2-4 qk010lh5 e4-2 qk010n4 e2-4 qk010n5 e2-4 qk010nh5 e4-2 qk010r4 e2-4 qk010r5 e2-4 qk010rh5 e4-2 qk012lh5 e4-2 qk012nh5 e4-2 qk012rh5 e4-2 qk015l5 e2-4 qk015n5 e2-4 qk015r5 e2-4 qk016lh3 e4-4 qk016lh4 e4-4 qk016lh6 e4-4 qk016nh3 e4-4 qk016nh4 e4-4 qk016nh6 e4-4 qk016rh3 e4-4 qk016rh4 e4-4 qk016rh6 e4-4 qk025k6 e4-4 qk025l6 e4-4 qk025n5 e2-4 qk025n6 e4-4 qk025r5 e2-4 qk025r6 e4-4 qk040k7 e4-4 s2004ds1 e5-2 s2004ds2 e5-2 s2004vs1 e5-2 s2004vs2 e5-2 s2006d e6-2 s2006ds2 e5-4 s2006ds3 e5-4 s2006f1 e6-2 s2006fs21 e5-4 s2006fs31 e5-4 s2006l e6-2 s2006ls2 e5-4 s2006ls3 e5-4 s2006v e6-2 s2006vs2 e5-4 s2006vs3 e5-4 s2008d e6-2 s2008ds2 e5-4 s2008ds3 e5-4 s2008f1 e6-2 s2008fs21 e5-4 s2008fs31 e5-4 s2008l e6-2 s2008ls2 e5-4 s2008ls3 e5-4 s2008r e6-2 s2008v e6-2 s2008vs2 e5-4 s2008vs3 e5-4 s2010d e6-2 s2010ds2 e5-4 s2010ds3 e5-4 s2010f1 e6-2 s2010fs21 e5-4 s2010fs31 e5-4 s2010l e6-2 s2010ls2 e5-4 s2010ls3 e5-4 s2010r e6-2 s2010v e6-2 s2010vs2 e5-4 s2010vs3 e5-4 s2012d e6-2 s2012r e6-2 s2012v e6-2 s2015l e6-4 s2016n e6-4 s2016r e6-4 s201e e6-2 s2020l e6-4 s2025l e6-4 s2025n e6-4 s2025r e6-4 s2035j e6-4 s2035k e6-4 s2040n e6-4 s2040r e6-4 s2055m e6-4 s2055n e6-4 s2055r e6-4 s2055w e6-4 s2065j e6-4 s2065k e6-4 s2070w e6-4 s2n1 e6-2 s2s e5-2 s2s1 e5-2 s2s2 e5-2 s2s3 e5-2 s4004ds1 e5-2 s4004ds2 e5-2 s4004vs1 e5-2 s4004vs2 e5-2 s4006d e6-2 s4006ds2 e5-4 s4006ds3 e5-4 s4006f1 e6-2 s4006fs21 e5-4 s4006fs31 e5-4 s4006l e6-2 s4006ls2 e5-4 s4006ls3 e5-4 s4006v e6-2 s4006vs2 e5-4 s4006vs3 e5-4 s4008d e6-2 s4008ds2 e5-4 s4008ds3 e5-4 s4008f1 e6-2 s4008fs21 e5-4 s4008fs31 e5-4 s4008l e6-2 s4008ls2 e5-4 s4008ls3 e5-4 s4008r e6-2 s4008v e6-2 s4008vs2 e5-4 s4008vs3 e5-4 s4010d e6-2 s4010ds2 e5-4 s4010ds3 e5-4 s4010f1 e6-2 s4010fs21 e5-4 s4010fs31 e5-4 s4010l e6-2 s4010ls2 e5-4 s4010ls3 e5-4 s4010r e6-2 s4010v e6-2 s4010vs2 e5-4 s4010vs3 e5-4 s4012d e6-2 s4012r e6-2 s4012v e6-2 s4015l e6-4 s4016n e6-4 s4016r e6-4 s401e e6-2 s4020l e6-4 s4025l e6-4 s4025n e6-4 s4025r e6-4 s4035j e6-4 s4035k e6-4 s4040n e6-4 s4040r e6-4 s4055m e6-4 s4055n e6-4 s4055r e6-4 s4055w e6-4 s4065j e6-4 s4065k e6-4 s4070w e6-4 s4n1 e6-2 s4s e5-2 s4s1 e5-2 s4s2 e5-2
part number index ?2002 teccor electronics a-31 http://www.teccor.com thyristor product catalog +1 972-580-7777 teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. teccor page part no. no. s4s3 e5-2 s6004ds1 e5-2 s6004ds2 e5-2 s6004vs1 e5-2 s6004vs2 e5-2 s6006d e6-2 s6006ds2 e5-4 s6006ds3 e5-4 s6006f1 e6-2 s6006fs21 e5-4 s6006fs31 e5-4 s6006l e6-2 s6006ls2 e5-4 s6006ls3 e5-4 s6006v e6-2 s6006vs2 e5-4 s6006vs3 e5-4 s6008d e6-2 s6008ds2 e5-4 s6008ds3 e5-4 s6008f1 e6-2 s6008fs21 e5-4 s6008fs31 e5-4 s6008l e6-2 s6008ls2 e5-4 s6008ls3 e5-4 s6008r e6-2 s6008v e6-2 s6008vs2 e5-4 s6008vs3 e5-4 s6010d e6-2 s6010ds2 e5-4 s6010ds3 e5-4 s6010f1 e6-2 s6010fs21 e5-4 s6010fs31 e5-4 s6010l e6-2 s6010ls2 e5-4 s6010ls3 e5-4 s6010r e6-2 s6010v e6-2 s6010vs2 e5-4 s6010vs3 e5-4 s6012d e6-2 s6012r e6-2 s6012v e6-2 s6015l e6-4 s6016n e6-4 s6016r e6-4 s601e e6-2 s6020l e6-4 s6025l e6-4 s6025n e6-4 s6025r e6-4 s6035j e6-4 s6035k e6-4 s6040n e6-4 s6040r e6-4 s6055m e6-4 s6055n e6-4 s6055r e6-4 s6055w e6-4 s6065j e6-4 s6065k e6-4 s6070w e6-4 s6n1 e6-2 s6s e5-2 s6s1 e5-2 s6s2 e5-2 s6s3 e5-2 s8006d e6-2 s8006l e6-2 s8006v e6-2 s8008d e6-2 s8008l e6-2 s8008r e6-2 s8008v e6-2 s8010d e6-2 s8010l e6-2 s8010r e6-2 s8010v e6-2 s8012d e6-2 s8012r e6-2 s8012v e6-2 s8015l e6-4 s8016n e6-4 s8016r e6-4 s8020l e6-4 s8025l e6-4 s8025n e6-4 s8025r e6-4 s8035j e6-4 s8035k e6-4 s8040n e6-4 s8040r e6-4 s8055m e6-4 s8055n e6-4 s8055r e6-4 s8055w e6-4 s8065j e6-4 s8065k e6-4 s8070w e6-4 sk006d e6-2 sk006l e6-2 sk006v e6-2 sk008d e6-2 sk008l e6-2 sk008r e6-2 sk008v e6-2 sk010d e6-2 sk010l e6-2 sk010r e6-2 sk010v e6-2 sk012d e6-2 sk012r e6-2 sk012v e6-2 sk015l e6-4 sk016n e6-4 sk016r e6-4 sk020l e6-4 sk025l e6-4 sk025n e6-4 sk025r e6-4 sk035k e6-4 sk040n e6-4 sk040r e6-4 sk055m e6-4 sk055n e6-4 sk055r e6-4 sk065k e6-4 st-32 e8-2 st-32b e8-2 st-34b e8-2 st-35 e8-2 st-36a e8-2 st-36b e8-2 st-40 e8-2 t106b1 e5-2 t106d1 e5-2 t106m1 e5-2 t107b1 e5-2 t107d1 e5-2 t107m1 e5-2 tcr22-4 e5-2 tcr22-6 e5-2 tcr22-8 e5-2

▲Up To Search▲

Price & Availability of BT136S-600E

	To Download BT136S-600E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .